4IPNET EAP700 User manual

EAP
7
00
V1.
1
0

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
i
Copyright Notice
The contents of this publication may not be reproduced in any part or as a whole,
stored, transcribed in an information retrieval system, translated into any language,
or transmitted in any form or by any means, mechanical, magnetic, electronic,
optical, photocopying, manual, or otherwise, without the prior written permission
of 4IPNET, INC.
Disclaimer
4IPNET, INC. does not assume any liability arising out the application or use of any
products, or software described herein. Neither does it convey any license under its
parent rights not the parent rights of others. 4IPNET further reserves the right to ma e
changes in any products described herein without notice. The publication is subject to
change without notice.
Trademarks
4IPNET (4ipnet) is a registered trademar of 4IPNET, INC. Other trademar s mentioned in
this publication are used for identification purposes only and may be properties of their
respective owners.

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
© 2010 4IPNET, INC.
- 1 -
Preface Package Contents
The 4ipnet EAP700 Wall Jack Access Point is
an in-the-wall Wi-Fi IEEE 802.11b/g AP,
designed to blend with any office, home
interior architecture or furnishings effortlessly.
EAP700 is an easy-to-install and
cost-effective solution for most of indoor
wireless deployments, including hotel rooms,
apartments, offices, classrooms, libraries,
private homes, public kiosks, etc. When
working under one of 4ipnet Controllers, the
combined network turns into an intelligent
building solution, a managed internet service,
or a Wi-Fi hotspot network of various scales.
This Quick Installation Guide provides
instructions for getting started with EAP700.
1.
EAP700 x 1
2. Quick Installation Guide (QIG) x 1
3. CD-ROM x 1
4. LED Sticker x 2
It is recommended to keep the
original packing material for possible
future shipment when repair or
maintenance is required. Any returned
product should be packed in its
original packaging to prevent damage
during delivery.
Optional accessories to be purchased
separately:
1. AC-DC Adaptor
2. U-shaped Wall & Ceiling Mounting
kit

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
© 2010 4IPNET, INC.
- 2 -
System Overview
Front Panel
①
①①
①. WES Button
 Press for 3 seconds to initiate Master AP’s WDS connection.
 Press and release immediately to initiate Slave AP’s WDS connection.
②
②②
②. RESET Button
 Pressing the button more than 3 seconds will reset the system to default settings.
③
③③
③. LAN Port
 The LAN port is for connection with wired network.
LED status indication:
④
④④
④. LAN LED
 OFF indicates no connection; ON indicates connection; BLINKING indicates
transmitting data.
⑤
⑤⑤
⑤. WLAN LED
 Green LED ON indicates system ready.
⑥
⑥⑥
⑥. Power LED
 Green LED On indicates power on; OFF indicates power off.

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
© 2010 4IPNET, INC.
- 3 -
In-Wall Panel
①
①①
①. POWER SOCKET
 Attach the power adapter here.
②
②②
②. PoE (LAN) Port
 The LAN port is for connection with wired networks or PoE Switch.

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
© 2010 4IPNET, INC.
- 4 -
Hardware Installation
Please follow the steps mentioned below to install the hardware of EAP700:
Before the installation, assemble the following parts accordingly for later in-wall placement.
①
①①
①. Unpack the package and remove the cover and the frame.
②
②②
②. Lock the screw correctly to the frame.

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
© 2010 4IPNET, INC.
- 5 -
③
③③
③. Slide the frame from the two sides to the front until locked to the fixed point.
④
④④
④. Cover it with faceplate and push the frame to the end.

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
© 2010 4IPNET, INC.
- 6 -
⑤
⑤⑤
⑤. Optional U-shaped mounting kit: Slide the frame from the two sides to the front until
locked to the fixed point, and adjust the angel of set to the wall.

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
© 2010 4IPNET, INC.
- 7 -
Installation Steps:
1. Place the EAP700 at proper location.
The best location for EAP700 is usually at the center of your wireless network.
2. Connect EAP700 to your network device.
Connect one end of the Ethernet cable to the LAN port of EAP700 and the other end of the
cable to a switch, a router or a hub. EAP700 is then connected to your existing wired LAN
network.
3. There are two ways to supply power over to EAP700.
(1) Connect the power adapter to the EAP700 power socket.
(2) EAP700 PoE (LAN) port is capable of transmitting DC currents via its PoE (LAN) port.
Connect an IEEE 802.3af-compliant PSE device, e.g. a PoE-switch, to the PoE (LAN)
port of EAP700 with the Ethernet cable.
Now, the Hardware Installation is completed.

Quick Installation Guide
Quick Installation GuideQuick Installation Guide
Quick Installation Guide
EAP700 Enterprise Access Point ENGLISH
© 2010 4IPNET, INC.
- 8 -
Getting Started
4ipnet EAP700 supports web-based configuration. Upon the completion of hardware installation,
EAP700 can be configured through a PC by using its web browser such as Mozilla Firefox 2.0 or
Internet Explorer version 6.0 and the above.
The default values of LAN IP address and subnet mask of EAP700 are:
IP Address:192.168.1.1
Subnet Mask: 255.255.255.0
•To access the web management interface, connect the administrator PC to the LAN port of
EAP700 via an Ethernet cable. Then, set a static IP address on the same subnet mask as
EAP700 in TCP/IP of your PC, such as the following example (Please note that the IP
address used shall not be duplicated with the IP address of other devices within the same
network.). In the Local Area Connection Properties, selecting the Internet Protocol (TCP/IP)
Properties, use the following IP address as the default setting:
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
•Launch the web browser on your PC by entering the IP address of EAP700
(http://192.168.1.1) at the address field, and then press Enter. The following Administrator
Login Page will then appear. Enter “admin” for both the Username and Password fields,
and then click Login to log in.
Username:“admin”
Password:“admin”