Aaeon PICO-BT01 User manual

PICO-ITX Board PICO-BT01
PICO-BT01
Intel® AtomTM SoC
Intel® I211 Ethernet
1 USB3.0, 2 USB2.0, 2 COM
4-bit Digital I/O
1 mSATA/ MiniCard (Full-size)
1 MiniCard (Half-size)
BIO Connector for Daughterboard
PICO-BT01 Rev. A Manual 1st Ed.
January 23, 2015

PICO-ITX Board PICO-BT01
Copyright Notice
This document is copyrighted, 2015. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, or for
any infringements upon the rights of third parties that may result
from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, AAEON assumes no liabilities resulting from errors or
omissions in this document, or from the use of the information
contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.
i

PICO-ITX Board PICO-BT01
Acknowledgments
All other products’ name or trademarks are properties of their
respective owners.
AMI is a trademark of American Megatrends Inc.
AMD®is trademark of Advanced Micro Devices.
Microsoft Windows®is a registered trademark of Microsoft
Corp.
ITE is a trademark of Integrated Technology Express, Inc.
IBM, PC/AT, PS/2, and VGA are trademarks of International
Business Machines Corporation.
SoundBlaster is a trademark of Creative Labs, Inc.
Please be notified that all other products’ name or trademarks
not be mentioned above are properties of their respective
owners.
ii

PICO-ITX Board PICO-BT01
Packing List
Before you begin installing your card, please make sure that
the following materials have been shipped:
1 Heat Spreader
1 COMs + line-out cable
1 DVD-ROM for Manual (in PDF Format) and
Drivers
1 PICO-BT01
If any of these items should be missing or damaged, please
contact your distributor or sales representative immediately.
iii

PICO-ITX Board PICO-BT01
Contents
Chapter 1 General Information
1.1 Introduction................................................................ 1-2
1.2 Features .................................................................... 1-3
1.3 Specifications ............................................................ 1-4
Chapter 2 Quick Installation Guide
2.1 Safety Precautions ..................................................2-2
2.2 Location of Connectors and Jumpers ...................... 2-3
2.3 Mechanical Drawing ................................................2-5
2.4 Heat Spreader Installation....................................... 2-12
2.5 List of Jumpers ......................................................2-12
2.6 List of Connectors ...................................................2-15
2.7 Setting Jumpers .....................................................2-17
2.8 Clear CMOS Jumper (JP1 1,3,5) ............................ 2-18
2.9 Auto Power Button Enable/Disable Selection
(JP1 2,4,6)..................................................................... 2-18
2.10 LVDS Port Operating Voltage Selection (JP3)......2-18
2.11 LVDS Port Backlight Inverter Voltage Selection
(JP4 1,3,5)..................................................................... 2-18
2.12 LVDS Backlight Lightness Control Mode Selection
(JP4 2,4,6)..................................................................... 2-19
2.13 Battery (CN1) ........................................................ 2-20
2.14 DDR3L SO-DIMM Slot (CN2)................................2-20
2.15 VGA Port (CN3)..................................................... 2-20
iv

PICO-ITX Board PICO-BT01
2.16 DP Port (CN4).......................................................2-21
2.17 LVDS Port Inverter / Backlight Connector (CN5)..2-22
2.18 LAN (RJ-45) Port (CN7)........................................2-23
2.19 Digital IO Port (CN8) ............................................. 2-24
2.20 MiniCard Slot (Full Size)/mSATA (By BIOS)
(CN9)............................................................................. 2-24
2.21 USB Ports 0 and 1 (CN10).................................... 2-27
2.22 USB 2.0 Port 3 (CN11)..........................................2-29
2.23 +5V Output for SATA HDD (CN14).......................2-29
2.24 SATA Port (CN15).................................................2-30
2.25 LPC Port (CN18)...................................................2-30
2.26 Front Panel (CN19)...............................................2-31
2.27 External +12V Input (CN20)..................................2-32
2.28 Buzzer Connector (CN21).....................................2-32
2.29 BIO Connector (CN22)..........................................2-32
2.30 MiniCard Slot (Half-Mini Card) (CN24).................. 2-34
2.31 LVDS Port (CN25).................................................2-37
2.32 COM Port 1/2 & Line Out Connector (CN27)........2-38
2.33 Electrical Specifications for I/O Port...................... 2-41
Chapter 3 AMI BIOS Setup
3.1 System Test and Initialization. ..................................3-2
3.2 AMI BIOS Setup........................................................ 3-3
Chapter 4 Driver Installation
4.1 Installation……………………………………………..4-3
v

PICO-ITX Board PICO-BT01
Appendix A Programming The Watchdog Timer
A.1 Watchdog Timer Registers ....................................A-2
A.2 Watchdog Sample Program...................................A-3
Appendix B I/O Information
B.1 I/O Address Map....................................................B-2
B.2 Memory Address Map............................................B-3
B.3 IRQ Mapping Chart................................................B-4
Appendix C Mating Connector
C.1 List of Mating Connectors and Cables.................. C-2
vi

PICO-ITX Board PICO-BT01
General
Information
Chapter
1
Chapter 1 General Information 1- 1

PICO-ITX Board PICO-BT01
1.1 Introduction
The PICO-BT01 is the embedded board with PICO-ITX form
factor AAEON developed. It supports Intel®’s Atom™
E3845/E3825 SoC Up to 1.91 GHz. Moreover, the Intel®
Atom™ E3845/E3825 SoC offers a high performance
computing platform with low power consumption. This new
product supports DDR3L SODIMM at speeds of 1066/1333
MHz, up to 8 GB.
One half size MiniCard and one mSATA/MiniCard interfaces
provide ample storages. With one Gigabit Ethernet, two COM
ports, and both USB3.0 and USB2.0 ports, the PICO-BT01
meets the requirements of today’s demanding applications.
Display requirements are met with an abundance of interfaces
such as VGA, DP and LVDS. The PICO-BT01 supports
18/24-bit LVDS with PWM function.
With all of its integrated features, the PICO-BT01 strikes a
balance of performance and price. This versatile product targets
Industrial Automation, Entertainment, Networking, KIOSK/POS,
Transportation, Banking, Healthcare and Digital Signage
applications that require high performance and high reliability.
Chapter 1 General Information 1-2

PICO-ITX Board PICO-BT01
1.2 Features
Intel® Atom™ E3845/E3825 SoC Up to 1.91 GHz
204-pin SODIMM DDR3L 1066/1333MHz up to 8GB
10/100/1000M Intel® I211 Ethernet
CRT, 18/24-bit LVDS, DP
VGA/DP co-lay Support
HD Audio for Line out
mSATA/MiniCard (Full-Size) Slot x 1, MiniCard (Half-size)
x 1
USB3.0 x 1, USB 2.0 x 2, COM x 2, 4-bit Digital I/O
BIO Connector for Daughter Board
Chapter 1 General Information 1-3

PICO-ITX Board PICO-BT01
1.3 Specifications
System

From Factor
PICO-ITX

Processor
Intel® Atom™ E3845/E3825 SoC
Up to 1.91 GHz

System Memory
204-pin SODIMM DDR3
1066/1333 MHz, up to 8 GB

Chipset
Intel Atom™ SoC

I/O Chipset
Fintek F81801

Ethernet
Intel® I211 x 1

BIOS
AMI BIOS-32 Mb ROM

Wake On LAN
Yes

Watchdog Timer
1-255 steps by software program

H/W Status
Monitoring
Monitoring system temperature,
voltage status

Expansion Interface
mSATA/ Mini Card (Full-size) x 1
(select with BIOS)
1 x MiniCard (Half-size)

Battery
Lithium Battery

Power Requirement
DC 12V, AT/ATX (Default)
Board Size 3.94" x 2.76" (100mm x 72mm)

Gross Weight
0.44 lbs (200g)

Operating
Temperature
32°F~140°F (0°C~60°C)

Storage Temperature
-40°F~176°F (-40°C~80°C)
Chapter 1 General Information 1-4

PICO-ITX Board PICO-BT01

Operating Humidity
0% ~ 90% relative humidity,
non-condensing
Display: Supports CRT/TFT LCD/DP

Chipset
Intel Atom™ SoC

Resolution
Up to 1440 x 900 (18/24-bit) @ 60
Hz for LVDS (select with BIOS or
jumper);
Up to 2048 x 1152 @ 60 Hz for
CRT
Up to 2560 x 1400 @ 60Hz for DP

LCD Interface
18/24-bit LVDS with PWM function
I/O: Fintek F81801U-I
Storage SATA2 x 1

Serial Port
RS-232 x 1
RS-232/422/485 x 1

USB
USB3.0 x 1
USB2.0 x 2

Digital I/O
4-bit Programmable (2-in/ 2-out)

Audio
HD Audio Codec (Realtek
ALC892)
Chapter 1 General Information 1-5

PICO-ITX Board
P I C O - B T 0 1
Chapter 2 Quick Installation Guide 2-1
Quick
Installation
Guide
Chapter
2

PICO-ITX Board
P I C O - B T 0 1
Chapter 2 Quick Installation Guide 2-2
2.1 Safety Precautions
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis

PICO-ITX Board
P I C O - B T 0 1
Chapter 2 Quick Installation Guide 2-3
2.2 Location of Connectors and Jumpers
Component Side
Component Side
Component Side

PICO-ITX Board
P I C O - B T 0 1
Chapter 2 Quick Installation Guide 2-4
Solder Side
Solder Side

PICO-ITX Board
P I C O - B T 0 1
Chapter 2 Quick Installation Guide 2-5
2.3 Mechanical Drawing
Component Side
Component Side
Component Side

PICO-ITX Board
P I C O - B T 0 1
Chapter 2 Quick Installation Guide 2-6
Solder Side
Solder Side

PICO-ITX Board
P I C O - B T 0 1
Chapter 2 Quick Installation Guide 2-7
Heat Spreader

PICO-ITX Board
P I C O - B T 0 1
Chapter 2 Quick Installation Guide 2-8
A
A
A
A
B
BB
B