ABB PM5630 User manual

DOC. N° 1SDH002203A1002
E-kit
User Manual

ABB | E-kit
2 | © 2022 ABB | - 1SDH002203A1002

3 | © 2022 ABB | - 1SDH002203A1002
1 - General information ............................................................... 5
Intended recipients...............................................................5
Purpose of the manual ........................................................5
Cyber security disclaimer ....................................................5
Rules for secure use.............................................................5
How to retrieve your credentials...........................................5
2 - Overview of E-kit..................................................................... 6
How E-kit functions..............................................................6
Templates supported by E-kit...............................................7
Available models ..................................................................7
Structure of E-kit..................................................................7
Access to the web interface .................................................7
SD card functions.................................................................7
3 - Power supply........................................................................... 8
Introduction..........................................................................8
Alerts ..................................................................................8
Description of terminal box ..................................................8
4 - RS-485 serial communication interface (COM1 port) ........... 9
Description of terminal box ..................................................9
Connection ports .................................................................9
Connection among devices................................................10
Maximum distance and ......................................................10
Type of cable required........................................................11
Termination resistor ...........................................................11
Pull-up and pull-down resistors..........................................11
Communication parameters ...............................................13
Baud Rate Disclaimer.........................................................13
5 - Ethernet communication interface (ports ETH1 and ETH2) 13
Introduction........................................................................13
Description of terminal box ................................................13
Type of cable required........................................................13
Maximum distance .............................................................13
Setting of static..................................................................14
Setting of static IP address with DHCP ..............................15
Configuration of .................................................................15
6 - Commissioning of E-kit ........................................................ 17
Power-up ...........................................................................17
Firmware upgrade .............................................................17
7 - E-kit user interface .............................................................. 18
User level ...........................................................................18
Usage session ...................................................................18
Access to the web interface ...............................................18
Homepage .........................................................................18
8 - Web interface configuration ................................................. 19
Access as Admin user........................................................19
Save changes.....................................................................19
Copy configuration.............................................................20
Configuration of a device ...................................................20
Model management ..........................................................23
9 - Use of the Web interface ...................................................... 27
Access as Guest user.........................................................27
Available information and actions.......................................27
10 - Integration with Ekip Connect 3 ........................................ 28
E-kit with Ekip Connect 3...................................................28
Requirements.....................................................................28
Procedure .........................................................................28
11 - Technical specifications ..................................................... 30
Dimensions ........................................................................30
Contents

ABB | E-kit
4 | © 2022 ABB | - 1SDH002203A1002

5 | © 2022 ABB | - 1SDH002203A1002
ABB | E-kit
General information
1 - General information
Intended recipients
of this document
This document is intended for system integrators.
A system integrator is an experienced person who is perfectly familiar with how to physically and functionally
connect different systems (hardware devices and/or software applications) and who works in compliance
with the laws in force.
Purpose of the manual
The purpose of this manual is to guide the user step by step through the E-kit commissioning operations.
The manual includes general information, with details on cyber security, a brief description of the product,
instructions on how to connect the hardware, instructions on how to configure and use E-kit.
Cyber security disclaimer
E-kit is designed to be connected and to communicate information and data via a network interface, which
must be connected to a secure network.
Solely the user is responsible for continuously providing and guaranteeing a secure connection between
the E-kit product and the network and establishing and maintaining appropriate measures (for example:
installation of firewalls, application of authentication measures, data encryption, installation of antivirus
programs, etc.). The user must protect the E-kit product, the network, his/her system and his/her interfaces
from all types of security breach, unauthorized access, interference, intrusion, loss and/or theft of data or
information. ABB and its affiliates are not liable for damages and/or losses related to such security breaches,
unauthorized accesses, interference, intrusion, loss and/or theft of data or information.
The ports used by E-kit are outlined in the table below
Protocol Port
ABB netConfig UDP 24576
Online access with driver 3S UDP BlkDrvUdp (with scan) UDP 1740
Online access with driver 3S TCP/IP BlkDrvTcp (no scan) TCP 11740
Modbus TCP Server TCP 502
Web Server TCP 80/443
FTP Server TCP 21
Rules for secure use
The Modbus protocol does not provide encryption, authentication or integrity checking of the transmitted
data.
In addition, the web server uses an http protocol that transmits data in cleartext and which could therefore
be liable to interception by unauthorized persons. For these reasons, communication via E-kit and the control
system is not totally secure.
To protect E-kit and make sure that it functions as expected, it must be connected to a reliable network, that
is, with restricted access and monitored. In addition, access to E-kit must be limited to persons authorized
to make changes to the configuration.
If communication between E-kit and a device is interrupted, the web interface of E-kit activates an alarm to
warn of the fault.
How to retrieve your credentials
If you lose of forget the password, send an e-mail to [e-mail] to reset and
choose a new password.