ABB FMT200-ECO2 User manual

—
ABB MEASUREMENT & AN
ALYTICS | OPERATING INSTRUCTION | OI/FMT200-ECO2-EN REV. H
Sensyflow FMT200
-ECO2
Thermal mass flowmeter
—
ABB Measurement & Analytics
For your local ABB contact, visit:
www.abb.com/contacts
For more product information, visit:
www.abb.com/flow
For air, integral mount design
Measurement made easy
OI/FMT200
-ECO2-EN Rev. H 08.2020
—
Sensyflow FMT200
-ECO2
Introduction
The Sensyflow FMT200
-ECO2 is a very compact
and highly dynamic mass flowmeter for air.
The Sensyflow FMT200
-ECO2 enables direct mass
or standard volume flow measurement in
pneumatic applications, for
example for the
control of painting robots or in press
urized air
systems.
Additional Information
Additional documentation on
Sensyflow FMT200-
ECO2
is available for download free of charge at
www.abb.com/
flow.
Alternatively simply scan this
code:
—
We reserve the right to make technical changes or
modify the contents of this document
without prior
notice. With regard to purchase orders, the agreed particulars shall prevail.
ABB does not accept any
responsibility whatsoever for potential errors or possible lack of
information in this document.
We reserve all rights in t
his document and in the subject matter and illustrations contained
therein.
Any reproduction, disclosure to third parties or utilization of its contents – in whole
or in parts
– is forbidden without prior written consent of ABB.
© ABB 2020 3KXF421004R4201

2 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
Table of contents
1Safety.......................................................................... 3
General information and instructions.................................. 3
Warnings.................................................................................... 3
Intended use .............................................................................4
Improper use.............................................................................4
Notes on data safety ...............................................................4
Warranty provisions.................................................................4
Manufacturer’s address ..........................................................4
Service address.........................................................................4
2Design and function ..................................................5
Overview ....................................................................................5
Device description ...................................................................6
3Product identification .............................................. 7
Name plate ................................................................................ 7
4Transport and storage.............................................. 7
Inspection.................................................................................. 7
Transport................................................................................... 7
Storing the device .................................................................... 7
Ambient conditions ............................................................ 7
Returning devices..................................................................... 7
5Installation .................................................................8
Safety instructions...................................................................8
Installation conditions ............................................................8
Mounting position...............................................................8
Inlet sections........................................................................8
Ambient conditions .................................................................9
Storage temperature range ..............................................9
Ambient temperature.........................................................9
IP rating.................................................................................9
Process conditions ..................................................................9
Measured medium temperature ......................................9
Measuring medium pressure ............................................9
Influences...................................................................................9
Installing the sensor ................................................................9
Install the sensor: ................................................................9
Electrical connections ...........................................................10
Terminal layout ..................................................................10
Electrical data for inputs and outputs ..........................10
Parameterize........................................................................... 11
6Commissioning ........................................................12
Checks prior to commissioning ...........................................12
Switching on the power supply............................................12
Inspection after power-up of the power supply ..........12
Status LED on the transmitter ........................................12
Install the parameterization program ................................13
Start the parameterization program ..................................13
Parameter overview .............................................................. 14
Parameter descriptions.........................................................15
Saving the parameterization ...........................................15
Menu bar..............................................................................15
‘Current Device Data’ Registration Tab (Start screen)17
‘Analog output’ Registration Tab................................... 20
‘Digital output’ Registration Tab ................................... 22
7Operation................................................................. 24
Safety instructions ................................................................ 24
8Diagnosis / Troubleshooting ................................ 24
General..................................................................................... 24
Status LED on the transmitter ....................................... 24
9Maintenance / Repair ..............................................25
General..................................................................................... 25
Cleaning................................................................................... 25
Returning devices .................................................................. 25
10 Dismounting and disposal..................................... 26
Dismounting........................................................................... 26
Disposal ................................................................................... 26
11 Accessories...............................................................27
Sensor ...................................................................................... 27
Small flange connections ..................................................... 28
Screwed connections and adapter..................................... 29
12 Specification ........................................................... 30
13 Additional documents............................................ 30
14 Appendix ...................................................................31
Return form..............................................................................31

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 3
1Safety
General information and instructions
These instructions are an important part of the product and
must be retained for future reference.
Installation, commissioning, and maintenance of the product
may only be performed by trained specialist personnel who have
been authorized by the plant operator accordingly. The specialist
personnel must have read and understood the manual and must
comply with its instructions.
For additional information or if specific problems occur that are
not discussed in these instructions, contact the manufacturer.
The content of these instructions is neither part of nor an
amendment to any previous or existing agreement, promise or
legal relationship.
Modifications and repairs to the product may only be performed
if expressly permitted by these instructions.
Information and symbols on the product must be observed.
These may not be removed and must be fully legible at all times.
The operating company must strictly observe the applicable
national regulations relating to the installation, function testing,
repair and maintenance of electrical products.
Warnings
The warnings in these instructions are structured as follows:
DANGER
The signal word ‘DANGER’ indicates an imminent danger.
Failure to observe this information will result in death or
severe injury.
WARNING
The signal word ‘WARNING’ indicates an imminent danger.
Failure to observe this information may result in death or
severe injury.
CAUTION
The signal word ‘CAUTION’ indicates an imminent danger.
Failure to observe this information may result in minor or
moderate injury.
NOTICE
The signal word ‘NOTICE’ indicates possible material damage.
Note
‘Note’ indicates useful or important information about the
product.

4 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
… 1 Safety
Intended use
Mass flow measurement of gases and gas mixtures in closed
pipelines.
The device has been designed for use exclusively within the
technical limit values indicated on the identification plate and in
the data sheets.
Improper use
The following are considered to be instances of especially
improper use of the device:
• Operation as a flexible compensating adapter in piping,
for example for compensating pipe offsets, pipe
vibrations, pipe expansions, etc.
• For use as a climbing aid, for example for mounting
purposes.
• For use as a bracket for external loads, for example as a
support for piping, etc.
• Material application, for example by painting over the
housing, name plate or welding/soldering on parts.
• Material removal, for example by spot drilling the
housing.
Notes on data safety
This product is designed to be connected to and to
communicate information and data via a network interface.
It is operator’s sole responsibility to provide and continuously
ensure a secure connection between the product and your
network or any other network (as the case may be).
Operator shall establish and maintain any appropriate measures
(such as but not limited to the installation of firewalls,
application of authentication measures, encryption of data,
installation of anti-virus programs, etc.) to protect the product,
the network, its system and the interface against any kind of
security breaches, unauthorized access, interference, intrusion,
leakage and / or theft of data or information.
ABB Automation Products GmbH and its affiliates are not liable
for damages and / or losses related to such security breaches,
any unauthorized access, interference, intrusion, leakage and /
or theft of data or information.
Warranty provisions
Using the device in a manner that does not fall within the scope
of its intended use, disregarding this manual, using
underqualified personnel, or making unauthorized alterations
releases the manufacturer from liability for any resulting
damage. This renders the manufacturer's warranty null and void.
Manufacturer’s address
ABB Automation Products GmbH
Measurement & Analytics
Schillerstr. 72
32425 Minden
Germany
Tel: [phone]
Fax: [phone]
Service address
Customer service center
Tel: [phone]
Email: automation.servi[email protected]bb.com

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 5
2Design and function
Overview
Figure 1: Sensor with different screw-in adapter (examples)
Design
Integral mount design
Model
Sensyflow FMT200-ECO2
Measuring media
Air
Measuring accuracy*
Measuring error < ±3 % of measured value, repeatability < ±0.5 % of measured value
Permissible measuring medium temperature Tmedium
−
25 to 50 °C (−13 to 122 °F)
Permissible operating
pressure
Standard: 10 × 102 kPa (10 bar abs.)
High-pressure version: 16 × 102 kPa (16 bar abs.)
Process connections
Small flange adapter ISO
-KF flange; screwed connection G ⅜ in, G ¾ in, G ½ in, G 1 in;
Legris hose adapter, Transair adapter
Wetted materials
Aluminum, Hostadur, tinned Cu, glass
Power supply
24
V DC, ±10 %
IP rating
in accordance with EN 60529: IP 65
Communication
serial, V24
/ RS232C
Outputs in serial production
Analog outputs
0 to 5 V DC, 0 to 10 V DC, 0/4 to 20 mA, min. / max. alarm
Digital output
Yes
Pulse / frequency output
Yes
Approvals and certificates
Available on abb.com/flow or on request
* The stated measuring accuracy only applies under the calibration conditions in the stated measuring range.

6 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
… 2 Design and function
Device description
1
Process adapter connection
2
Status LED
3
Electric coupler connector
Figure 2: Device design
The Sensyflow FMT200-ECO2 is a compact, highly dynamic
measuring system for mass flow or standard volume flow
measurement of air.
The flowmeter sensor has been designed in the form of an easy-
to-install meter tube which accommodates the sensor unit and
the evaluation electronics. It directly provides a linearized output
signal, and is calibrated and immediately ready for use.
A standard RS 232 interface allows you to change over between
the individual output signals (current, voltage, frequency, pulse
and alarm) and parameterize the device.
Thanks to its flexible connection concept, the measuring system
can be installed in piping or hoses of different types and sizes. A
variety of connection adapters are available for this purpose.
A standard power supply unit can be used to supply power to the
Sensyflow FMT200-ECO2.
Physics of measurement
Thermal flow metering procedures use different ways to
evaluate the flow dependent cooling of a heated resistor as
measuring signal.
In a hotfilm anemometer with temperature difference control,
the heated platinum resistor is maintained at a constant
overtemperature in relation to an unheated platinum sensor
inside the gas flow. The heating power required for maintaining
the overtemperature depends directly on the flow rate and the
material properties of the gas. Given a known (and constant) gas
composition, the mass flow can be determined by electronically
evaluating the heater current /mass flow curve without
additional pressure and temperature compensation. Together
with the standard density of the gas this results directly in the
standard volume flow. Considering the high measuring range
dynamics up to 1:100, an accuracy smaller than 1 % of the
measuring value is achieved.
1
Gas temperature measurement
resistor (RMG)
2
Heating resistor (RH)
q
mGas mass current
I
HHeating actual value
Figure 3: Analog measuring principle
The gas flows past two temperature-sensitive resistors, RHand
RMG, which are part of an electric bridge circuit. Due to the
chosen resistance ratio RH< RMG, RHis heated by the current IH.
RMG adopts the same temperature as the gas. The current IHis
preset by the electronic control circuit to produce a constant
temperature difference between the heated resistor RHand the
temperature of the gas.
The electric power generated in resistor RHexactly compensates
its loss of heat to the gas flow. As this loss of heat is dependent
on the number of particles which collide with the surface of
resistor RH, IHrepresents a measure of the mass flow rate.

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 7
3Product identification
Name plate
Note
The name plates displayed are examples. The device
identification plates affixed to the device can differ from this
representation.
1
Type designation
2
Manufacturer
3
CE marking
4
‘Read operating instruction’
symbol
5
Year of manufacture
6
Measuring medium pressure
7
Measuring medium temperature
8
IP rating
9
Power supply
0
Firmware version
k
Serial number
l
Production number
Figure 4: Name plate (example)
4Transport and storage
Inspection
Check the devices immediately after unpacking for possible
damage that may have occurred from improper transport.
Details of any damage that has occurred in transit must be
recorded on the transport documents.
All claims for damages must be submitted to the shipper
without delay and before installation.
Transport
If the original packaging material is no longer available, wrap the
device in bubble wrap or corrugated cardboard and place it in a
box of sufficient size lined with a shock-absorbing material (e.g.,
foam rubber). The thickness of the padding should be
appropriate for the device weight and type of shipment. The box
must be labeled as “fragile”.
For overseas shipment, always add a desiccant (e.g., silica gel)
and hermetically seal the device plus desiccant in a layer of
polythene that is 0.2 mm thick. Use an amount of desiccant that
is appropriate for the packing volume and the expected
transport time (at least for three months). You should also line
the box with a layer of union paper.
Storing the device
Bear the following points in mind when storing devices:
• Store the device in its original packaging in a dry and
dust-free location.
• Observe the permitted ambient conditions for transport
and storage.
• Avoid storing the device in direct sunlight.
• In principle, the devices may be stored for an unlimited
period. However, the warranty conditions stipulated in
the order confirmation of the supplier apply.
Ambient conditions
Refer to Ambient conditions on page 9.
Returning devices
For the return of devices, follow the instructions in Returning
devices on page 25.

8 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
5Installation
Safety instructions
WARNING
Risk of injury due to live parts.
Improper work on the electrical connections can result in
electric shock.
• Connect the device only with the power supply switched
off.
• Observe the applicable standards and regulations for the
electrical connection.
WARNING
Risk of injury due to process conditions.
The process conditions, for example high pressures and
temperatures, toxic and aggressive measuring media, can
give rise to hazards when working on the device.
• Before working on the device, make sure that the process
conditions do not pose any hazards.
• If necessary, wear suited personal protective equipment
when working on the device.
• Depressurize and empty the device / piping, allow to cool
and purge if necessary.
Installation conditions
Mounting position
Any mounting position can be selected.
Inlet sections
To prevent negative effects on measuring accuracy, the ISO-
KF flange DN 25, Transair, G ³⁄₄ in and G 1 should be provided
in the inlet sections when using the connections.
Straight undisturbed pipe sections must be provided as inlet
sections; they should have a length of approx. 10 × D on the
inlet side.
These inlet sections make sure that any disturbances of the
flow profile are eliminated before reaching the actual
measuring point at the sensor.
If maintaining the required inlet sections is not possible, a
flow conditioner can be retrofitted. However, the flow
conditioner causes a significantly increased pressure drop.
When using the G ½ in and G ⅜ in adapters, no additional
inlet sections are required, as flow straightener components
are implemented on the inlet side of the adapters. Note that
flow conditioners cause considerable pressure drop.
Installation of setting equipment
Components affecting the flow, e.g. valves or shut-off valves
should be installed on the outlet side, therefore downstream
of the measuring point.

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 9
Ambient conditions
Storage temperature range
−30 to 85 °C (−22 to 185 °F)
Ambient temperature
−25 to 50 °C (−13 to 122 °F)
IP rating
IP 65
Process conditions
Measuring medium
Air
Measuring ranges*
0 (1) to 100 kg / h or 0 (12) to 1250 Nl / min**
* Reference values are given for applications with air under atmospheric
conditions. The values in brackets indicate the low limit of the measuring
range for which the measured value accuracy indicated is specified.
** You can specify any unit, as long as it can be transformed into a mass or
standard volume flow. (notation also: l / min-qn).
Measured medium temperature
−25 to 50 °C (−13 to 122 °F)
Measuring medium pressure
Standard: 10 × 102 kPa (10 bar abs.)
High-pressure version: 16 × 102 kPa (16 bar abs.)
Influences
Temperature effect
< 0.1 % / K of measured value
Pressure effect
≤ 0.2 % / 100 kPa (/bar) of the measured value
Pressure drop
< 10 kPa (100 mbar) at full scale and using the small flange
adapter DN 25; decreasing
approx. quadratically at smaller flow rates.
Installing the sensor
Before installing the sensor, observe the following points:
• The ambient conditions at the installation site comply
with the requirements in Ambient conditions on page 9.
• The operating pressure complies with the requirements
in Measuring medium pressure on page 9
• For each measuring system a calibration certificate is
delivered which contains all the key information (such as
serial number, calibrated measuring range, order number,
outputs set in delivery status). It must be checked
whether this data complies with the requirements of the
measuring point.
Install the sensor:
1. Install the sensor with process adapters in the piping.
2. Create the electrical connections in accordance with the
information Electrical connections on page 10.
Note
The variable process adapters are fastened in the sensor with a
fine pitch thread. The connection can be cautiously loosened
using a SW 30 open-end wrench.
Before carefully reinserting the process adapters, the threads
should be cleaned and lightly lubricated. Make sure the O-ring is
seated properly.

10 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
… 5 Installation
Electrical connections
Terminal layout
Please use the supplied cable for the electrical connection of the
flowmeter sensor. It is connected to the sensor with the plug.
Use a 24 V DC power supply with safe isolation in accordance
with EN 61010 and IEC 950 with a maximum output power of
< 150 W only.
Note
The Sensyflow eco1 and Sensyflow FMT200-ECO2 measuring
systems are compatible. With use of the appropriate adapter
plug, the Sensyflow FMT200-ECO2 can be connected to existing
installations.
As the ‘interface’ and ‘digital output’ functionalities are not
available in Sensyflow eco1, they are not wired-on in the adapter
plug.
A
Sensor
B
Connection cable
Figure 5: Electrical connection
Coupler connector
Sub-D connector, series 712, 8-pin, IP 65
Pin
Color
Function / comments
1
White
Analog output, signal (+)
2
Brown
RS 232C TxD – transmi data
3
Green
Pulse / frequency output, signal (+)
4
Yellow
Power supply +24 V DC
5
Gray
Power supply GND
6
Pink
RS 232C RxD – receive data
7
Blue
Analog output, GND
8
Red
Pulse / frequency output + RS 232C, GND
Shield
—
Functional earth
Note
Insulate any unused wire ends.
Electrical data for inputs and outputs
Power supply
Integral mount design
Pin / color
4+ (yellow) / 5− (gray)
Operating voltage
24 V DC (±10 %)
Input Current
Peak < 1 A; operation < 0.6 A
Fuse
At least 2 A slow-blow
Power consumption
< 15 W
Analog output
Can be optionally configured as current output (0 (4) to 20 mA)
or voltage output (0 to 10 (5) V).
Current output
active*
Pin / color
1+ (white) / 7− (blue)
Output signal
0
(4) to 20 mA
Signal in the event of an
error
<
3.5 mA or > 22 mA
Load RB
<
500 Ω
Voltage output
Active
Pin / color
1+ (white) / 7− (blue)
Output signal
0 to 10 (5) V
Signal in the event of an
error
Min. or max.
Input Current
< 1 mA
* When selecting the current output 0 (4) to 20 mA, the analog output
supplies an active signal. The device delivers the current independently
without external power supply.

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 11
Digital output
Can be configured as pulse / frequency outputs or binary
outputs.
Figure 6: Connection example
The digital output offers a 24 V HIGH signal or a 0 V LOW signal.
The output can be wired as active or passive.
Digital output (passive)
Pin / color
3+ (green)
/ 8- (red)
Umax
24 V DC
Imax
−
20 mA
fmax
2500 Hz
The output current must be limited to
-20 mA in LOW state to guarantee an
output voltage Ua
< 2.5 V.
Digital output (active)
Pin / color
3+ (green) / 8− (red)
Imax
1
mA
fmax
2500 Hz
The output current must be limited to 1
mA in HIGH state to guarantee an
output voltage Ua
> 15 V.
Communication
RS
232
Pin / color
TxD: 2 (brown)
/ RxD: 6 (pink) / GND: 8− (red)
Baud rate
9600 bits/sec.
Stop bits
1
Parity
None
Data bits
8
Parameterize
The Sensyflow FMT200-ECO2 can simultaneously operate one
analog output (current 0 / 4 to 20 mA or voltage 0 to 5 / 10 V),
one digital output (frequency, pulse, alarm) and a serial RS 232
interface.
Parameterization of the measuring system can also take place
via the serial interface. Using a PC or laptop, you can change the
output signal used or the adjust the settings of the measuring
ranges and signals.
The parameterization program is included in the standard scope
of delivery. A service and parameterization box is optionally
available for easier connection of the SensyFlow FMT200-ECO2
in the test field. That way, the various input and output variables
can be read out quickly and easily.
1
Power supply
2
Polarity reversal protection
3
Analog outputs
4
Digital output (pulse/freq)
5
Connector for Sensyflow FMT200
-
ECO2
6
Connector for PC, Laptop
Figure 7: Service and parameterization box

12 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
… 5 Installation
… Parameterize
The configuration box is available as an option. It is used to
simplify wiring for testing and configuration purposes. The
electric system is largely based around a star hub, which
distributes the signals from the 8-wire connection cable of the
device to the different input and output
contacts.
Power supply
The 24 V DC voltage is connected via a ‘5.5 mm external / 2 mm
internal’ jack plug. Polarity is irrelevant, as the configuration box
features protection against polarity reversal.
LED
The LED signals green when a power supply is connected.
Analog output
The analog signal can be tapped at these terminals. The analog
signal represents the current measured value. It can be a 0 (4) ...
20 mA current signal (I) or a 0 ... 5 (10) V voltage signal (U).
Digital output
The BNC female connector is used to tap the 24 V digital signal.
Depending on the parameterization, this can be a frequency
signal, counter pulse, or a logical min. / max.signal.
Connector for Sensyflow FMT200-ECO2
This female connector is used to connect the device via the
connection cable included in the scope of delivery of the
parameterization box.
Serial interface
This enables a PC or laptop COM x interface to be connected to
the parameterization box via a commercially available serial
cable.
The configuration program can be used to customize measuring
ranges and output signals in line with requirements.
6Commissioning
Checks prior to commissioning
The following points must be checked before commissioning the
device:
• Correct wiring in accordance with Electrical connections
on page 10.
• The ambient conditions must comply with the
requirements in Ambient conditions on page 9.
• The power supply must meet the requirements set out on
the name plate.
Switching on the power supply
1. Switch on the power supply.
• The status LED blinks red during the initialization phase
(approx. 30 s).
• After the initialization phase, the status LED lights up in a
continuous green color.
2. Perform parameterization of the flowmeter (see
Parameterize on page 11).
The flowmeter is now ready for operation.
Inspection after power-up of the power supply
The following points must be checked after commissioning the
device:
• Parameter configuration must correspond to the
operating conditions.
Status LED on the transmitter
The status LED on the transmitter indicates the operating
condition of the device and displays possible faults.
LED
Description
Continuous green light
The sensor is ready for operation.
Green flashing
The measuring range set has been up-scaled.
Continuous red light
Parameter or hardware fault on the sensor.
• Reestablish parameterization, see
Reestablish
the parameterization on page 15.
• Repairs required, contact ABB Service.
Red blinking
Initialization phase of the device.
(approx. 30 s after power-up of the power supply
or after parameter changes)
Red slowly blinking
Undervoltage.
Check the supply power
Red quickly blinking
EEPROM fault.
Repairs required, contact ABB Service.

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 13
Install the parameterization program
The parameterization program is located on the provided USB
stick.
The parameterization program must be installed on a PC /
laptop:
1. Insert the USB stick into the PC / laptop.
2. Open the USB stick in Explorer.
3. Launch the ‘SETUP.EXE’ file with administrator rights.
4. Follow the instructions in the installation program.
Change the preset installation directory as needed.
5. Select the desired language (German, English or French).
The language can be changed in the parameterization
program only.
Start the parameterization program
1. Connect the sensor to an open RS232 interface of the PC /
laptop using the D-Sub adapter. If no RS232 interface is
available, additionally use the USB-RS232 adapter.
2. Power-up the power supply of the sensor.
3. To launch the parameterization program, execute the
‘P_Compact_V100.exe’ file in the installation directory.
• The COM 1 interface is used by default. If another interface is
used, select it in the ‘Connection’ menu.
• Confirm the selected interface by pressing ‘OK’. If no
connection can be established, an error message will appear.
In this case, check the following points:
– Check the interface connection with the PC / laptop.
– Is the sensor ready for operation?
(Is the status LED on the sensor continuous green)
– Has the correct interface been selected.
• If the interface connection has been successfully established,
the starting screen of the parameterization program is
displayed (see ‘Current Device Data’ Registration Tab (Start
screen) on page 17).

14 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
… 6 Commissioning
Parameter overview
CURRENT DEVICE DATA
ANALOG OUTPUT
CURRENT
0 to 20 mA
4 to 20 mA
VOLTAGE
0 to 10 V
0 to 5V
DIGITAL OUTPUT
FREQUENCY OUTPUT
10 to 1000 Hz
1 to 100 Hz
PULSE OUTPUT VARIABLE 1 to 2500 Hz
SWITCH OUTPUT PULSE LENGTH
PULSE EVALUATION
TOTALIZER
MIN. LIMIT
MAX. LIMIT
SERVICE
(for manufacturer service only)

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 15
Parameter descriptions
NOTICE
Data loss
Data loss due to the shut-off of power supply during the
initialization phase (status LED blinks red) of the device.
• Do not switch off the power supply until the device is
ready for operation(status LED is continuous green).
Saving the parameterization
If any parameterization has been changed in the
parameterization program and transferred to the device through
the ‘Accept’ button, a save / initialization phase of the device
follows and the status LED blinks red.
• The supply voltage must not be switched off until the status
LED is continuous green once more.
The modified parameters will not be saved properly if this rule is
not obeyed.
After the repeated power-up of the device, a data inconsistency
will be detected during the initialization phase, the status LED
will switch to continuous red and the device will no longer
function correctly.
Reestablish the parameterization
Once the status LED is continuous red, communication with the
parameterization software can be resumed.
1. The parameterization data must be resaved by selecting the
‘Accept’ button.
• Wait until the symbol indicating that a program is running
disappears and the status indication for the ‘initialization
phase’ is terminated.
• The status LED is still continuous red at this stage.
2. Perform a hardware reset by powering down and powering
up the power supply.
• After the initialization phase, the status LED is
continuous green and the device is ready for operation.
Note
If operation readiness cannot be reestablished, contact ABB
Service.
Menu bar
Menu / parameter
Description
Configuration
Factory settings
Shows the parameters set at the factory
Savings
Saves the current parameter set to a data storage
medium.
Load
Loads a saved parameter set from a data storage
medium.
Delete
Deletes a saved parameter set from a data storage
medium.
Print
Prints the current parameter set to the configured
standard printer.
Select Language
Select the program language:
German, English, French
Select unit
Select the flow unit from a unit list.
Insert / delete unit
Create / delete a new unit.
Refer to
Add user-defined unit
on page 16.
Exit
Exits the parameterization program.
Connection
Connection
Select the serial interface for connection with the
sensor.
Data backup
Data backup
Save the changed data to the device

16 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
… 6 Commissioning
… Parameter descriptions
Add user-defined unit
Figure 8: ‘Add unit’ menu
A user-defined unit can be created here. The unit must have the
possibility of being presented as a multiple of kg/h.
Parameter
Description
Unit
Name of the unit (text field).
Factor
Enter the factor of the unit in kg/h. Decimal numbers
must be entered using a period rather than a comma.
Standard condition
Enter the standard state to which the unit makes
reference.
Example: 0 °C, 1013mbar
Gas type
Enter the gas type for the unit (text field).
Available units
Display the available units.
Cancel
Cancel the entry.
Savings
Save the new unit.
Delete unit
Delete units

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 17
… 6 Commissioning
… Parameter descriptions
‘Current Device Data’ Registration Tab (Start screen)
1
Menu bar
2
Registration Tab
3
Device identification
4
Current measured value
5
Standard condition parameter display (when selecting a volume unit)
6
Status bar
7
Sensor connection status
8
Analog output parameter display
9
Digital output parameter display (only if configured)
Figure 9: Parameterization program, ‘Current Device Data’ Registration Tab

18 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
… 6 Commissioning
… Parameter descriptions
Device detection
Display information on the connected sensor.
Parameter
Description
Production number
Unique serial number of the connected sensor, please
provide this number with any inquiry to ABB.
Version
Sensor firmware software version.
Measured value
Figure 10: ‘Measured value’ field
In the measured value area, the current measured value is
displayed in % as a bar graph.
If the digital output of the sensor is configured as a switch
output (see ‘Switch output’ option on page 23), the graph
displays the up-scale or down-scale of the set limit value:
• If the current measured value down-scales the set lower
limit, the bar has a blue color.
• If the current measured value up-scales the set upper
limit, the bar has a red color.
• If the current measured value is within the set limits, the
bar has a green color.
Standard condition
Figure 11: Standard condition field
When a volume unit is selected (e.g. Nm3/h), the unit always
makes reference to a defined standard condition.
In the standard condition field, the absolute pressure and
reference temperature for the selected volume unit is displayed.
When a mass flow unit is selected (e.g. kg/h) the field remains
empty.
Status bar
Display of information and help texts for the current action. In
addition, the current date and time are displayed.
Digital output
Display of the digital output configuration.
Frequency output option:
Figure 12: Frequency option
The current measured value is output as a frequency on the
digital output.
Parameter
Description
Frequency [min]
Frequency in Hz for ‘0’ flow.
Frequency [max]
Frequency in Hz for the set upper range value.

Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H 19
Impulse output option:
Figure 13: Impulse output
The current measured value is output in impulses/unit on the
digital output.
Parameter
Description
Value
Set flow rate per impulse.
Duration
Set impulse length.
Polarity
Set polarity (low/high) for the impulse.
Switch option:
Figure 14: Switch
The current measured value is monitored for fluctuation either
side of an adjustable limit value.
The polarity gives the condition of the signal within the set
limits.
Parameter
Description
Threshold min
Set lower limit value.
Threshold max
Set upper limit value.
Polarity
Set polarity (low/high).

20 Sensyflow FMT200-ECO2 THERMAL MASS FLOWMETER | OI/FMT200-ECO2-EN REV. H
… 6 Commissioning
… Parameter descriptions
‘Analog output’ Registration Tab
1
‘Configure’ area, selection of the parameters to be configured via check
box / .
2
Display of the currently set values
3
Display of the newly selected values
Figure 15: Parameterization program, ‘Analog Output’ Registration Tab
This tab is used to configure the analog output. For the sake of transparency, both the current and amended values are displayed at
the same time.
• The parameters to be changed should be selected using the check box and the values changed in the entry field.
• The changed values are saved to the sensor using the ‘Accept’ button.
The sensor is restarted and initialized (LED on the transmitter blinks red). No measured values are displayed during initialization.