ABB Relion 611 Series User manual

—
RELION® PROTECTION AND CONTROL
611 series
Technical Manual

Document ID: 1MRS757454
Issued: 2019-04-10
Revision: D
Product version: 2.0
© Copyright 2019 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third party,
nor used for any unauthorized purpose.
The software or hardware described in this document is furnished under a license and
may be used, copied, or disclosed only in accordance with the terms of such license.
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
www.abb.com/relion

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or
product description and are not to be deemed as a statement of guaranteed properties.
All persons responsible for applying the equipment addressed in this manual must
satisfy themselves that each intended application is suitable and acceptable, including
that any applicable safety or other operational requirements are complied with. In
particular, any risks in applications where a system failure and/or product failure
would create a risk for harm to property or persons (including but not limited to
personal injuries or death) shall be the sole responsibility of the person or entity
applying the equipment, and those so responsible are hereby requested to ensure that
all measures are taken to exclude or mitigate such risks.
This product has been designed to be connected and communicate data and
information via a network interface which should be connected to a secure network.
It is the sole responsibility of the person or entity responsible for network
administration to ensure a secure connection to the network and to take the necessary
measures (such as, but not limited to, installation of firewalls, application of
authentication measures, encryption of data, installation of anti virus programs, etc.)
to protect the product and the network, its system and interface included, against any
kind of security breaches, unauthorized access, interference, intrusion, leakage and/or
theft of data or information. ABB is not liable for any such damages and/or losses.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested to
notify the manufacturer. Other than under explicit contractual commitments, in no
event shall ABB be responsible or liable for any loss or damage resulting from the use
of this manual or the application of the equipment.

Conformity
This product complies with the directive of the Council of the European Communities
on the approximation of the laws of the Member States relating to electromagnetic
compatibility (EMC Directive 2014/30/EU) and concerning electrical equipment for
use within specified voltage limits (Low-voltage directive 2014/35/EU). This
conformity is the result of tests conducted by ABB in accordance with the product
standard EN 60255-26 for the EMC directive, and with the product standards EN
60255-1 and EN 60255-27 for the low voltage directive. The product is designed in
accordance with the international standards of the IEC 60255 series.

Table of contents
Section 1 Introduction.....................................................................17
This manual...................................................................................... 17
Intended audience............................................................................ 17
Product documentation.....................................................................18
Product documentation set..........................................................18
Document revision history........................................................... 18
Related documentation................................................................19
Symbols and conventions.................................................................19
Symbols.......................................................................................19
Document conventions................................................................ 19
Functions, codes and symbols.................................................... 20
Section 2 611 series overview........................................................25
Overview...........................................................................................25
Product series version history..................................................... 26
PCM600 and relay connectivity package version........................26
Local HMI......................................................................................... 27
Display.........................................................................................27
LEDs............................................................................................28
Keypad........................................................................................ 28
Web HMI...........................................................................................29
Command buttons....................................................................... 30
Authorization.....................................................................................31
Audit trail......................................................................................32
Communication.................................................................................34
Self-healing Ethernet ring............................................................ 35
Ethernet redundancy................................................................... 36
Secure communication................................................................ 38
Section 3 Basic functions............................................................... 39
General parameters..........................................................................39
Self-supervision................................................................................ 45
Internal faults............................................................................... 45
Warnings..................................................................................... 47
LED indication control.......................................................................49
Function block............................................................................. 49
Functionality................................................................................ 49
Programmable LEDs........................................................................ 49
Function block............................................................................. 49
Functionality................................................................................ 50
Table of contents
611 series 1
Technical Manual

Signals.........................................................................................53
Settings........................................................................................53
Monitored data.............................................................................55
Time synchronization........................................................................55
Time master supervision GNRLLTMS.........................................55
Function block........................................................................ 55
Functionality........................................................................... 55
Signals....................................................................................57
Settings.................................................................................. 57
Parameter setting groups................................................................. 59
Function block............................................................................. 59
Functionality................................................................................ 59
Test mode.........................................................................................61
Functionality................................................................................ 61
Control mode............................................................................... 61
Authorization................................................................................62
LHMI indications.......................................................................... 62
Local/Remote control........................................................................62
Fault recorder FLTRFRC..................................................................63
Function block............................................................................. 63
Functionality ............................................................................... 63
Settings........................................................................................64
Monitored data.............................................................................65
Nonvolatile memory..........................................................................73
Binary input.......................................................................................73
Binary input filter time.................................................................. 73
Binary input inversion.................................................................. 74
Oscillation suppression................................................................75
Binary outputs...................................................................................75
Power output contacts ................................................................ 76
Dual single-pole power outputs PO1 and PO2.......................76
Double-pole power outputs PO3 and PO4 with trip circuit
supervision............................................................................. 77
Signal output contacts ................................................................ 77
Internal fault signal output IRF .............................................. 78
Signal outputs SO1 and SO2 in power supply module.......... 78
Signal outputs SO1, SO2 and SO3 in BIO0006..................... 79
GOOSE function blocks....................................................................79
GOOSERCV_BIN function block................................................. 80
Function block........................................................................ 80
Functionality........................................................................... 80
Signals....................................................................................80
GOOSERCV_MV function block..................................................80
Table of contents
2611 series
Technical Manual

Function block........................................................................ 80
Functionality........................................................................... 80
Signals....................................................................................81
Configurable logic blocks..................................................................81
Minimum pulse timer................................................................... 81
Minimum pulse timer TPGAPC.............................................. 81
Minimum pulse timer TPSGAPC............................................ 82
Move (8 pcs) MVGAPC............................................................... 84
Function block........................................................................ 84
Functionality........................................................................... 84
Signals....................................................................................84
Settings.................................................................................. 85
Factory settings restoration.............................................................. 85
ETHERNET channel supervision function blocks.............................85
Redundant Ethernet channel supervision RCHLCCH................. 85
Function block........................................................................ 85
Functionality........................................................................... 86
Signals....................................................................................86
Settings.................................................................................. 86
Monitored data....................................................................... 86
Ethernet channel supervision SCHLCCH....................................87
Function block........................................................................ 87
Functionality........................................................................... 87
Signals....................................................................................87
Settings.................................................................................. 88
Monitored data....................................................................... 88
Section 4 Protection functions........................................................89
Three-phase current protection........................................................ 89
Three-phase non-directional overcurrent protection PHxPTOC..89
Identification........................................................................... 89
Function block........................................................................ 89
Functionality........................................................................... 89
Operation principle................................................................. 90
Measurement modes..............................................................92
Timer characteristics.............................................................. 93
Application..............................................................................94
Signals..................................................................................100
Settings................................................................................ 102
Monitored data..................................................................... 104
Technical data...................................................................... 105
Technical revision history..................................................... 106
Three-phase directional overcurrent protection DPHxPDOC.... 107
Identification......................................................................... 107
Table of contents
611 series 3
Technical Manual

Function block...................................................................... 107
Functionality......................................................................... 107
Operation principle .............................................................. 107
Measurement modes............................................................112
Directional overcurrent characteristics ................................ 113
Application............................................................................121
Signals..................................................................................123
Settings................................................................................ 124
Monitored data..................................................................... 128
Technical data...................................................................... 129
Technical revision history..................................................... 130
Three-phase thermal protection for feeders, cables and
distribution transformers T1PTTR............................................. 130
Identification......................................................................... 130
Function block...................................................................... 131
Functionality......................................................................... 131
Operation principle............................................................... 131
Application............................................................................134
Signals..................................................................................135
Settings................................................................................ 135
Monitored data..................................................................... 136
Technical data...................................................................... 137
Technical revision history..................................................... 137
Motor load jam protection JAMPTOC........................................137
Identification......................................................................... 137
Function block...................................................................... 137
Functionality......................................................................... 137
Operation principle............................................................... 138
Application............................................................................139
Signals..................................................................................139
Settings................................................................................ 140
Monitored data..................................................................... 140
Technical data...................................................................... 140
Technical revision history..................................................... 141
Loss of load supervision LOFLPTUC........................................ 141
Identification......................................................................... 141
Function block...................................................................... 141
Functionality......................................................................... 141
Operation principle............................................................... 141
Application............................................................................142
Signals..................................................................................143
Settings................................................................................ 143
Monitored data..................................................................... 144
Table of contents
4611 series
Technical Manual