ABB Relion 611 Series Installation and operation manual

—
RELION® PROTECTION AND CONTROL
611 series
Engineering Manual

Document ID: 1MRS241255
Issued: 2019-04-10
Revision: B
Product version: 2.0
© Copyright 2019 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third party,
nor used for any unauthorized purpose.
The software or hardware described in this document is furnished under a license and
may be used, copied, or disclosed only in accordance with the terms of such license.
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
www.abb.com/relion

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or
product description and are not to be deemed as a statement of guaranteed properties.
All persons responsible for applying the equipment addressed in this manual must
satisfy themselves that each intended application is suitable and acceptable, including
that any applicable safety or other operational requirements are complied with. In
particular, any risks in applications where a system failure and/or product failure
would create a risk for harm to property or persons (including but not limited to
personal injuries or death) shall be the sole responsibility of the person or entity
applying the equipment, and those so responsible are hereby requested to ensure that
all measures are taken to exclude or mitigate such risks.
This product has been designed to be connected and communicate data and
information via a network interface which should be connected to a secure network.
It is the sole responsibility of the person or entity responsible for network
administration to ensure a secure connection to the network and to take the necessary
measures (such as, but not limited to, installation of firewalls, application of
authentication measures, encryption of data, installation of anti virus programs, etc.)
to protect the product and the network, its system and interface included, against any
kind of security breaches, unauthorized access, interference, intrusion, leakage and/or
theft of data or information. ABB is not liable for any such damages and/or losses.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested to
notify the manufacturer. Other than under explicit contractual commitments, in no
event shall ABB be responsible or liable for any loss or damage resulting from the use
of this manual or the application of the equipment.

Conformity
This product complies with the directive of the Council of the European Communities
on the approximation of the laws of the Member States relating to electromagnetic
compatibility (EMC Directive 2014/30/EU) and concerning electrical equipment for
use within specified voltage limits (Low-voltage directive 2014/35/EU). This
conformity is the result of tests conducted by ABB in accordance with the product
standard EN 60255-26 for the EMC directive, and with the product standards EN
60255-1 and EN 60255-27 for the low voltage directive. The product is designed in
accordance with the international standards of the IEC 60255 series.

Safety information
Dangerous voltages can occur on the connectors, even though the
auxiliary voltage has been disconnected.
Non-observance can result in death, personal injury or substantial
property damage.
Only a competent electrician is allowed to carry out the electrical
installation.
National and local electrical safety regulations must always be
followed.
The frame of the protection relay has to be carefully earthed.
When the plug-in unit has been detached from the case, do not touch
the inside of the case. The relay case internals may contain high
voltage potential and touching these may cause personal injury.
The protection relay contains components which are sensitive to
electrostatic discharge. Unnecessary touching of electronic
components must therefore be avoided.
Whenever changes are made in the protection relay, measures should
be taken to avoid inadvertent tripping.

Table of contents
Section 1 Introduction.......................................................................5
This manual........................................................................................ 5
Intended audience.............................................................................. 5
Product documentation.......................................................................6
Product documentation set............................................................6
Document revision history............................................................. 6
Related documentation..................................................................7
Symbols and conventions...................................................................7
Symbols.........................................................................................7
Document conventions.................................................................. 7
Functions, codes and symbols...................................................... 8
Section 2 Relay engineering process.............................................13
Monitoring and control system structure...........................................14
Standard configuration concept........................................................15
Workflow...........................................................................................16
Section 3 PCM600 tool...................................................................19
Connectivity packages......................................................................20
PCM600 and relay connectivity package version.............................20
Installing connectivity packages.................................................. 21
Installing connectivity packages by using the connectivity
package installer.................................................................... 21
Installing connectivity packages by using Update Manager...21
Activating connectivity packages.................................................22
PCM600 projects.............................................................................. 22
Technical key....................................................................................23
IEC 61850 naming conventions to identify an IED...................... 24
Setting the technical key..............................................................26
Communication between PCM600 and the protection relay............ 28
Setting up IP addresses.............................................................. 29
IED Update....................................................................................... 29
Prerequisites for local and remote updates................................. 30
Updating firmware or language................................................... 30
Section 4 Setting up a project........................................................ 33
Creating a new project......................................................................33
Building the plant structure............................................................... 34
Inserting an IED................................................................................35
Inserting an IED in online mode.................................................. 36
Table of contents
611 series 1
Engineering Manual

Inserting an IED in offline mode.................................................. 44
Inserting an IED from the template directory............................... 46
Inserting an IED by importing a .pcmi file.................................... 48
Setting the IED IP address in a project.............................................49
COM600S project............................................................................. 51
Selecting communication port for configuration...........................51
Importing a 611 series protection relay in a COM600S project... 52
Using the Web HMI.......................................................................... 55
Managing IED users......................................................................... 55
PCM600 project's IEC 61850 version identification..........................58
Section 5 Protection and control engineering................................ 59
Parameter Setting tool......................................................................59
Configuration parameter..............................................................59
Setting parameter........................................................................ 59
Setting group............................................................................... 59
Parameter import and export.......................................................60
Parameter organization............................................................... 60
Signal Matrix.....................................................................................60
Fault Record tool.............................................................................. 61
Opening and closing Fault Record tool....................................... 61
Fault Record tool interface.......................................................... 63
IED Compare....................................................................................64
Starting IED Compare................................................................. 64
IED Compare tool interface......................................................... 65
Protection and control blocking examples........................................ 66
Section 6 LHMI engineering...........................................................67
HMI event filtering.............................................................................67
Starting HMI event filtering.......................................................... 68
Setting visibility of HMI events.....................................................68
Searching events.........................................................................68
Saving event filter configuration.................................................. 69
Section 7 IEC 61850 communication engineering......................... 71
IEC 61850 protocol references and pre-conditions.......................... 71
IEC 61850 interface..........................................................................71
IEC 61850 interface in the protection relay................................. 74
GOOSE data exchange..........................................................74
Function view for IEC 61850 in PCM600.....................................75
Station configuration description file types.................................. 76
IEC 61850 engineering process....................................................... 76
Exporting SCL files from PCM600...............................................77
Exporting SCD files................................................................ 77
Table of contents
2611 series
Engineering Manual

Exporting ICD or CID files...................................................... 79
Engineering vertical and horizontal communication.................... 80
Importing SCL files to PCM600................................................... 82
Importing SCD files................................................................ 83
Importing ICD or CID files...................................................... 84
Writing communication configuration to the IED..........................85
IEC 61850 version change while writing configuration to the
IED...............................................................................................86
Section 8 Configuration migration.................................................. 87
Configuration migration workflow..................................................... 87
Preconditions for configuration migration......................................... 88
Backup creation................................................................................88
Migrating the IED configuration........................................................ 88
Reengineering the migrated configuration........................................91
Reengineering in the Parameter Setting tool...............................91
Reengineering in the IEC 61850 Configuration tool.................... 91
Reengineering in the Communication Management tool.............91
Checking and updating Modbus points ................................. 91
Section 9 Glossary......................................................................... 93
Table of contents
611 series 3
Engineering Manual

4

Section 1 Introduction
1.1 This manual
1.2 Intended audience
This manual addresses system and project engineers involved in the engineering
process of a project, and installation and commissioning personnel, who use technical
data during engineering, installation and commissioning, and in normal service.
The system engineer must have a thorough knowledge of the application, protection
and control equipment and the configured functional logic in the relays. The
installation and commissioning personnel must have a basic knowledge of handling
electronic equipment.
1MRS241255 B Section 1
Introduction
611 series 5
Engineering Manual

1.3 Product documentation
1.3.1 Product documentation set
Planning & purchase Engineering Installation Commissioning Operation Maintenance Decommissioning, deinstallation & disposal
Quick start guide
Quick installation guide
Brochure
Product guide
Operation manual
Installation manual
Connection diagram
Engineering manual
Technical manual
Application manual
Communication protocol manual
IEC 61850 engineering guide
Point list manual
Cyber security deployment guideline
GUID-0777AFDA-CADF-4AA9-946E-F6A856BDF75E V1 EN
Figure 1: The intended use of manuals in different lifecycles
Product series- and product-specific manuals can be downloaded
from the ABB Web site http://www.abb.com/relion.
1.3.2 Document revision history
Document revision/date Product series version History
A/2016-02-22 2.0 First release
B/2019-04-10 2.0 Content updated
Download the latest documents from the ABB Web site
http://www.abb.com/substationautomation.
Section 1 1MRS241255 B
Introduction
6611 series
Engineering Manual

1.3.3 Related documentation
Product series- and product-specific manuals can be downloaded from the ABB Web
site http://www.abb.com/substationautomation.
1.4 Symbols and conventions
1.4.1 Symbols
The caution icon indicates important information or warning related
to the concept discussed in the text. It might indicate the presence of
a hazard which could result in corruption of software or damage to
equipment or property.
The information icon alerts the reader of important facts and
conditions.
The tip icon indicates advice on, for example, how to design your
project or how to use a certain function.
Although warning hazards are related to personal injury, it is necessary to understand
that under certain operational conditions, operation of damaged equipment may result
in degraded process performance leading to personal injury or death. Therefore,
comply fully with all warning and caution notices.
1.4.2 Document conventions
A particular convention may not be used in this manual.
• Abbreviations and acronyms are spelled out in the glossary. The glossary also
contains definitions of important terms.
• Push button navigation in the LHMI menu structure is presented by using the
push button icons.
To navigate between the options, use and .
• Menu paths are presented in bold.
Select Main menu/Settings.
• LHMI messages are shown in Courier font.
To save the changes in nonvolatile memory, select Yes and press .
• Parameter names are shown in italics.
The function can be enabled and disabled with the Operation setting.
• Parameter values are indicated with quotation marks.
The corresponding parameter values are "On" and "Off".
• Input/output messages and monitored data names are shown in Courier font.
1MRS241255 B Section 1
Introduction
611 series 7
Engineering Manual

When the function starts, the START output is set to TRUE.
• This document assumes that the parameter setting visibility is "Advanced".
1.4.3 Functions, codes and symbols
All available functions are listed in the table. All of them may not be applicable to all
products.
Table 1: Functions included in the relays
Function IEC 61850 IEC 60617 IEC-ANSI
Protection
Three-phase non-directional
overcurrent protection, low stage,
instance 1
PHLPTOC1 3I> (1) 51P-1 (1)
Three-phase non-directional
overcurrent protection, high stage,
instance 1
PHHPTOC1 3I>> (1) 51P-2 (1)
Three-phase non-directional
overcurrent protection, high stage,
instance 2
PHHPTOC2 3I>> (2) 51P-2 (2)
Three-phase non-directional
overcurrent protection, instantaneous
stage, instance 1
PHIPTOC1 3I>>> (1) 50P/51P (1)
Non-directional earth-fault protection,
low stage, instance 1 EFLPTOC1 Io> (1) 51N-1 (1)
Non-directional earth-fault protection,
low stage, instance 2 EFLPTOC2 Io> (2) 51N-1 (2)
Non-directional earth-fault protection,
high stage, instance 1 EFHPTOC1 Io>> (1) 51N-2 (1)
Non-directional earth-fault protection,
instantaneous stage EFIPTOC1 Io>>> 50N/51N
Three-phase directional overcurrent
protection, low stage, instance 1 DPHLPDOC1 3I> -> (1) 67-1(1)
Three-phase directional overcurrent
protection, low stage, instance 2 DPHLPDOC2 3I> -> (2) 67-1(2)
Three-phase directional overcurrent
protection, high stage, instance 1 DPHHPDOC1 3I>> -> (1) 67-2(1)
Directional earth-fault protection, low
stage, instance 1 DEFLPDEF1 Io> -> (1) 67N-1 (1)
Directional earth-fault protection, low
stage, instance 2 DEFLPDEF2 Io> -> (2) 67N-1 (2)
Directional earth-fault protection, high
stage DEFHPDEF1 Io>> -> 67N-2
Transient/intermittent earth-fault
protection INTRPTEF1 Io> -> IEF 67NIEF
Non-directional (cross-country) earth
fault protection, using calculated Io EFHPTOC1 Io>> (1) 51N-2 (1)
Negative-sequence overcurrent
protection, instance 1 NSPTOC1 I2> (1) 46 (1)
Table continues on next page
Section 1 1MRS241255 B
Introduction
8611 series
Engineering Manual

Function IEC 61850 IEC 60617 IEC-ANSI
Negative-sequence overcurrent
protection, instance 2 NSPTOC2 I2> (2) 46 (2)
Negative-sequence overcurrent
protection for machines, instance 1 MNSPTOC1 I2>M (1) 46M (1)
Negative-sequence overcurrent
protection for machines, instance 2 MNSPTOC2 I2>M (2) 46M (2)
Phase discontinuity protection PDNSPTOC1 I2/I1> 46PD
Residual overvoltage protection,
instance 1 ROVPTOV1 Uo> (1) 59G (1)
Residual overvoltage protection,
instance 2 ROVPTOV2 Uo> (2) 59G (2)
Residual overvoltage protection,
instance 3 ROVPTOV3 Uo> (3) 59G (3)
Three-phase undervoltage protection,
instance 1 PHPTUV1 3U< (1) 27(1)
Three-phase undervoltage protection,
instance 2 PHPTUV2 3U< (2) 27(2)
Three-phase undervoltage protection,
instance 3 PHPTUV3 3U< (3) 27(3)
Three-phase overvoltage protection,
instance 1 PHPTOV1 3U> (1) 59(1)
Three-phase overvoltage protection,
instance 2 PHPTOV2 3U> (2) 59(2)
Three-phase overvoltage protection,
instance 3 PHPTOV3 3U> (3) 59(3)
Positive-sequence undervoltage
protection, instance 1 PSPTUV1 U1< (1) 47U+(1)
Positive-sequence undervoltage
protection, instance 2 PSPTUV2 U1< (2) 47U+(2)
Negative-sequence overvoltage
protection, instance 1 NSPTOV1 U2> (1) 47O-(1)
Negative-sequence overvoltage
protection, instance 2 NSPTOV2 U2> (2) 47O-(2)
Frequency protection, instance 1 FRPFRQ1 f>/f<,df/dt (1) 81(1)
Frequency protection, instance 2 FRPFRQ2 f>/f<,df/dt (2) 81(2)
Three-phase thermal protection for
feeders, cables and distribution
transformers
T1PTTR1 3Ith>F 49F
Loss of load supervision LOFLPTUC1 3I< 37
Motor load jam protection JAMPTOC1 Ist> 51LR
Motor start-up supervision STTPMSU1 Is2t n< 49,66,48,51LR
Phase reversal protection PREVPTOC1 I2>> 46R
Thermal overload protection for
motors MPTTR1 3Ith>M 49M
Circuit breaker failure protection CCBRBRF1 3I>/Io>BF 51BF/51NBF
Three-phase inrush detector INRPHAR1 3I2f> 68
Master trip, instance 1 TRPPTRC1 Master Trip (1) 94/86 (1)
Table continues on next page
1MRS241255 B Section 1
Introduction
611 series 9
Engineering Manual

Function IEC 61850 IEC 60617 IEC-ANSI
Master trip, instance 2 TRPPTRC2 Master Trip (2) 94/86 (2)
High-impedance differential
protection for phase A, instance 1 HIAPDIF1 dHi>(1) 87(1)
High-impedance differential
protection for phase B, instance 2 HIBPDIF1 dHi>(2) 87(2)
High-impedance differential
protection for phase C, instance 3 HICPDIF1 dHi>(3) 87(3)
Switch onto fault CBPSOF1 SOTF SOTF
Other
Input switch group ISWGAPC ISWGAPC ISWGAPC
Output switch group OSWGAPC OSWGAPC OSWGAPC
Selector SELGAPC SELGAPC SELGAPC
Minimum pulse timer (2 pcs) TPGAPC TP TP
Minimum pulse timer (2 pcs, second
resolution), instance 1 TPSGAPC TPS (1) TPS (1)
Move (8 pcs), instance 1 MVGAPC MV (1) MV (1)
Control
Circuit-breaker control CBXCBR1 I <-> O CB I <-> O CB
Emergency start-up ESMGAPC1 ESTART ESTART
Autoreclosing DARREC1 O -> I 79
Condition monitoring and supervision
Trip circuit supervision, instance 1 TCSSCBR1 TCS (1) TCM (1)
Trip circuit supervision, instance 2 TCSSCBR2 TCS (2) TCM (2)
Runtime counter for machines and
devices MDSOPT1 OPTS OPTM
Phase segregated CT supervision
function for phase A, instance 1 HZCCASPVC1 MCS 1I(1) MCS 1I(1)
Phase segregated CT supervision
function for phase B, instance 2 HZCCBSPVC1 MCS 1I(2) MCS 1I(2)
Phase segregated CT supervision
function for phase C, instance 3 HZCCCSPVC1 MCS 1I(3) MCS 1I(3)
Logging
Disturbance recorder RDRE1 DR (1) DFR(1)
Fault recorder FLTRFRC1 - FR
Measurement
Three-phase current measurement,
instance 11) CMMXU1 3I 3I
Sequence current measurement CSMSQI1 I1, I2, I0 I1, I2, I0
Residual current measurement,
instance 1 RESCMMXU1 Io In
Three-phase voltage measurement,
instance 1 VMMXU1 3U 3U
Three-phase voltage measurement,
instance 2 VMMXU2 3U(B) 3U(B)
Table continues on next page
Section 1 1MRS241255 B
Introduction
10 611 series
Engineering Manual

Function IEC 61850 IEC 60617 IEC-ANSI
Sequence voltage measurement,
instance 1 VSMSQI1 U1, U2, U0 U1, U2, U0
Residual voltage measurement RESVMMXU1 Uo Vn
Frequency measurement, instance 1 FMMXU1 f f
Three-phase power and energy
measurement, instance 1 PEMMXU1 P, E P, E
1) In REB611, CMMXU is used for measuring differential phase currents
1MRS241255 B Section 1
Introduction
611 series 11
Engineering Manual

12