ABB SACE Tmax T5 1000V DC User manual

C
Doc. N.° 1SDH001351R0001 - L9714
SACE Tmax T5 1000V DC for Jumpers
B
A
G
HI
ABC D E F
57 150 162.5 114 210 102.5
G H I
625 120 300
Cubicle Dimensions [mm]
A
B
D
EC
A
METALLIC
FRAME
XX
Y
Y
F
UPPER SUPPLY
XX
Y
Y
A
A
METALLIC
FRAME
LOWER SUPPLY
B
D
E
C F
120
2 Nm
0 mm
For 4PS solution consider distances D, E, F symmetricaly with respect to X-X CB axis
Istruzioni di installazione Tmax T5 1000V DC per Jumpers
Installation instructions Tmax T5 1000V DC for Jumpers
Installationsanleitung Tmax T5 1000V DC für Jumpers
Instructions pour l'installation Tmax T5 1000V DC pour Jumpers
Instrucciones de instalación Tmax T5 1000V DC para Jumpers
Insulation distances for installation
in metallic cubicle [mm]

F
D
Tmax | ABB
G
If the device is equipped
with motor operator, MOE,
openings with current shall
be performed using SOR or
UVR.
E
(mm) CON MOSTRINA
WITH FLANGE
SENZA MOSTRINA
WITHOUT FLANGE
B 115 109
C 115 107
D 64.5 60.5
OFF ON
CLACK
TRIPPED
176
88
93
ø5.5 (M5)
C
B
D
= =
XX
Y
Y
23.25
Usare sempre connessioni isolate. Per configurazioni di cablaggio diverse da quelle di seguito rappresentate
eseguire prove di tipo specifiche sull'installazione e usare connessioni isolate
Always use insulated terminals connections. For different wiring configurations than those shown afterwards perform
specific type test on the installation and use insulated terminals connections
Bitte verwenden Sie ausschliesslich isolierte (Terminal-) Verbindungen. Für Konfigurationen mit anderer Verdrahtung
als unten stehend abgebildet, sind spezifische Stücknachweise auf der Installation auszuführen und isolierte
Anschlüsse zu benutzen.
Utiliser toujours des connexions isolées. Pour les configurations de câblage différentes de celle représentées ci-
dessous, effectuer des essais spécifiques de type sur l'installation et utiliser des connexions isolées
Usar siempre conexiones aisladas. Para configuraciones de cableado distintas a las que se representan a
continuación efectuar pruebas de tipo específicas en la instalación y usar conexiones aisladas
始终需要使用绝缘的端子连接. 对不同于后续所示的布线，需对安装进行指定的型式试验，并使用绝缘的端子连接

105
59.5
86.25
Tmax | ABB
I
2PS+2PS solution, Lower Supply
LOAD
F
74
205
= =
60
Example for 2P+2PS (Lower Supply)
H
Jumper examples
Example for 4PS (Lower Supply)
28 Nm
28 Nm
28 Nm
2PS+2PS
FCCu FCCuAl
240mm2300mm22x120mm22x240mm
2R
F
2x240mm2 240mm2
X
X
Y
Y
X
X
186
46.5 46.5 46.5
ø10.5
max 35
max 11
242
114
139
66
20

LOAD
* Terminals configurations must be symmetrical with respect to x-x CB axis when CB is supplied from the top
Tmax | ABB
K2PS+2PS solution, Upper Supply
2PS+2PS solution, Lower Supply - Terminals
R
X
X
162.5
Ø11
35
46.5
100
2PS+2PS
FCCu FCCuAl
240mm2300mm22x120mm22x240mm
2R
F
2x240mm2 240mm2
J
2
FCCu 2x240mm
46.5 46.5
X
X
162.5
21.5Ø2x
25
28
22.5
56.5
46.5
21.5Ø2x
28
32
30
70
2
FCCu 2x240mm
46.5 46.5 46.5
XX
162.5
46.5 46.5 46.5
2
FCCuAl 2x120mm
15.9Ø2x
22
25.4
22.5
56.5
25Nm
XX
162.5
24
46.5 46.5 46.5
X
X
162.5
27
24
2
FCCu 240mm
46.5 46.5 46.5
X
X
162.5
21.6Ø
23.6
2
FCCuAl 240mm 2 FCCuAl 300mm
46.5 46.5 46.5
X
X
162.5
24.5Ø
24
46.5 46.5

L
1
CLACK
2
www.abb.com
© Copyright 2011 ABB. All rights reserved.
MIN
最小值
(0,7)
MED
中间值
(0,85)
MAX
最大值
(1xIn)
224 272 320
280 340 280
350 425 500
In
TMA
I1
最小值
(In x 5)
MED
中间值
(In x 7,5)
MAX
最大值
(In x 10)
320 1600 2400 3200
400 2000 3000 4000
500 2500 3750 5000
MIN
In
TMA
I3 (*)
* Consider corrective factor of 1,2
320
400
500
For more information please contact:
ABB S.p.A.
ABB SACE Division
Via Pescaria, 35
24123 Bergamo - Italy
250A