ABB ATS022 User manual

Automatic transfer switch ATS022
Installation and operating instructions
1SDH000760R0002

3
1SDH000760R0002, L4106
Installation and operating instructions, ATS022Contents
Contents
1. Introduction ....................................................................................................................... 4
1.1 Use of symbols .............................................................................................................................4
1.2 Standards .....................................................................................................................................4
1.3 Safety notes..................................................................................................................................5
1.4 Explanations of abbreviations and terms .....................................................................................6
2. Product overview .............................................................................................................. 7
2.1 Typical applications ......................................................................................................................7
2.2 Functions of automatic transfer switch ATS022........................................................................... 8
3. Description ..................................................................................................................... 10
3.1 ATS outputs ................................................................................................................................10
3.1.1 Opening/closing command to circuit breakers, DO1...DO4 .......................................................10
3.1.2 Gen-Set start/stop, DO5.............................................................................................................10
3.1.3 Alarm signaling, DO6 ..................................................................................................................10
3.1.4 Protection device alarm signaling, DO9 .....................................................................................10
3.1.5 Auto/Manual signaling, DO10.....................................................................................................10
3.1.6 Disconnection Secondary Loads, DO11 ....................................................................................10
3.2 ATS inputs .................................................................................................................................. 10
3.2.1 CBs status Input, DI1, DI2 ..........................................................................................................10
3.2.2 CB Withdrawn ............................................................................................................................11
3.2.3 CB Trip, DI4, DI5 .........................................................................................................................11
3.2.4 Gen-Set Alarm, DI8..................................................................................................................... 11
3.2.5 Forced switching to the emergency supply line, DI9..................................................................11
3.2.6 Switching logic enable/disabled, DI3 .........................................................................................11
3.2.7 The command to startup the generator, DI10.............................................................................11
3.2.8 Third CB status input, DI11 ........................................................................................................11
3.2.9 Voltage sensors input .................................................................................................................12
3.2.10 Measurements ............................................................................................................................12
3.3 Application scenarios .................................................................................................................12
3.3.1 Two transformer incoming lines..................................................................................................13
3.3.2 Transformer on normal line and generator on emergency line ................................................... 15
3.3.3 Special scenarios........................................................................................................................16
4. Operating......................................................................................................................... 17
4.1 Automatic transfer switch ATS022 in Manual Mode...................................................................17
4.2 Automatic transfer switch ATS022 in Automatic Mode ..............................................................19
4.3 TEST sequence...........................................................................................................................20
5. Installation ...................................................................................................................... 21
5.1 Automatic transfer switch ATS022, door mounting....................................................................21
5.2 Automatic transfer switch ATS022, DIN-rail mounting ...............................................................22
6. Connecting ...................................................................................................................... 23
6.1 Power circuit of the automatic transfer switch ATS022..............................................................23
6.2 Control circuit .............................................................................................................................23
6.2.1 Control circuit of the automatic transfer switch ATS022 ............................................................24
7. Technical data ................................................................................................................. 26
7.1 Automatic transfer switch ATS022, power circuits.....................................................................26
8. Using automatic transfer switch ATS022 ..................................................................... 27
8.1 Interface......................................................................................................................................27
8.2 Configuration ..............................................................................................................................27
8.2.1 Keypad........................................................................................................................................27
8.2.2 LEDs ...........................................................................................................................................28
8.2.3 Display ........................................................................................................................................29
8.2.4 Communication via Modbus....................................................................................................... 37
9. Technical data of the automatic transfer switch ........................................................ 39
10. Troubleshooting .............................................................................................................. 40
10.1 Alarms in ATS022........................................................................................................................40

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
4
1. Introduction
Hazardous voltage: warns about a situation where a hazardous voltage may cause
physical injury to a person or damage to equipment.
General warning: warns about a situation where something other than electrical
equipment may cause physical injury to a person or damage to equipment.
Caution: provides important information or warns about a situation that may have
a detrimental effect on equipment.
Information: provides important information about the equipment.
1. Introduction
This manual describes the installation and the basic operation of the automatic transfer switch ATS022
used with circuit breakers.
1.1 Use of symbols
1.2 Standards
The ATS022 are compliant with the following standards:
European Directive 73/23 “LVD – Low Voltage Directive”
EN-IEC 50178 electronic equipment for use in power installations
EN-IEC 62103 electronic equipment for use in power installations
EN-IEC 60947-5-1 low voltage switchgear and control gear: control circuit devices and switching
elements
Electromagnetic compatibility EN 50081-2, EN 50082-2
Environmental conditions IEC 68-2-1, IEC 68-2-2, and IEC 68-2-3
EN-IEC 61000-4-2: Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques
Section 2: Electrostatic discharge immunity test Basic EMC Publication (IEC 1000-4-2 [8KV air,
4KV cont])
EN-IEC 61000-4-3, Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques Section 3: Radiated, radio-frequency, electromagnetic field immunity test
(IEC 1000-4-3 [level 3])
EN-IEC 61000-4-4, Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques Section 4: Electrical fast transient/burst immunity test Basic EMC Publication
(IEC 1000-4-4 [level 2/3])
EN-IEC 61000-4-5, Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques Section 5: Surge immunity test (IEC 1000-4-5 [level 1/2])
EN-IEC 61000-4-6: Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques (IEC 1000-4-6 [level 3])

5
1SDH000760R0002, L4106
Installation and operating instructions, ATS022
1. Introduction
Even if the unit seems to be in stand by status, switch it OFF before operating on
circuit breakers. It may happen that the unit would operate the circuit breakers without
warning.
EN-IEC 61000-4-8: Electromagnetic compatibility (EMC) - Part 4: Testing and measurement
techniques (IEC 1000-4-8 [level 5])
EN-IEC 50093, Electromagnetic compatibility (EMC) - Part 4: Testing and measurement techniques
Section 11: Voltage dips, short interruptions and voltage variations immunity test (IEC1000-4-11,
[100ms/5s] B, C criterion)
CISPR11 (30MHz...1GHz): Emission (Generic Standard, Industrial) – Radiated
CISPR11 (0.15MHz…30MHz): Emission (Generic Standard, Industrial) – Conducted
CISPR/CEI 1000-6-3: Part 6: Generic standards – Section 3: Emission standard for residential,
commercial and light-industrial environments
IEC 60068-2-2: Environmental testing. Part 2: Tests. Test B: Dry heat
IEC 60068-2-6: Environmental testing. Part 2: Tests. Test Fc: vibration (sinusoidal)
IEC 60068-2-27: Environmental testing. Part 2: Tests. Test Ea and guidance: shock
IEC 60068-2-30: Environmental testing. Part 2: Tests. Test Db and guidance: Damp heat, cyclic
IEC 60068-2-1: Environmental testing. Part 2: Tests. Test A: cold (-20 °C ± 3 °C, 16 hours)
1.3 Safety notes
If there are doubts about safety use, the unit must put out of service.
The automatic transfer switch ATS022 must be prevented from operating the circuit breaker before
accessing the circuit breakers
performing maintenance on circuit breakers or any electrical circuits powered by them
performing any other operations where opening/closing the circuit breakers could be dangerous
During maintenance, it is advisable to lock the circuit breaker mechanically to the open position
Safe use is not possible if:
1. The unit has been damaged during transport
2. The unit shows visible signs of damage
3. The unit does not work
4. The unit has been stored for a long period

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
6
1.4 Explanations of abbreviations and terms
ATS: The control unit of automatic transfer switching equipment, in this document called
the automatic transfer switch
ATS022: The automatic transfer switch, high version with communication and display
Bus tie: Circuit breaker connecting two section of electrical plant
CB: Circuit Breaker
Emergency line: Power supply line, the secondary line used in emergency cases
Modbus RTU: Bus communication protocol
Normal line: Power supply line, the primary line normally used
Test sequence: A sequence to test the functionality of the ATS and the connected circuit breakers
TS: Switching delay, time after which ATS022 sends an opening command to the
protection device on the normal line
TCE: Close emergency delay, time after which ATS022 sends a closing command to the
protection device on the emergency line
TBS: Back switching delay, time after which ATS022 sends an opening command to the
protection device on the emergency line
TCN: Close normal delay, time after which ATS022 sends an closing command to the
protection device on the normal line
TGOFF: Generator stop delay, time after which the ATS022 sends stopping command to the
generator.
1. Introduction

7
1SDH000760R0002, L4106
Installation and operating instructions, ATS022
KA00428
G
KA00427
2. Product overview
2. Product overview
The transfer switch concept is applied to any installations requiring switching from the main power circuit
to another to ensure the supply of loads.
2.1 Typical applications
A. Network line – GenSet line
In case of loss of the main’s network the ATS022 device manages the switching to the emergency line
equipped with a GenSet system
Figure 2.2 Network line a - Network line b
Automatic transfer switch type ATS022 is designed for single- and three-phase distribution systems in
diverse applications. ATS022 will control the switching between two power supplies. The ATS022 unit
measures the voltage level of the normal line and controls the two main protection devices of the two
monitored lines in order to guarantee the continuity of the power supply.
Figure 2.1 Network line - GenSet line
B. Network line a – Network line b
In case of loss of the main’s network the ATS022 device manages the switching to a second line used as
an emergency source.

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
8
Figure 2.3 Automatic transfer switch ATS022
ATS022:
Analysing the voltage, frequency and the phase balance. Includes the generator START / STOP command.
Communication via Modbus RTU.
DI/DO, Digital input / output, see control circuit diagrams.
An external 24...110 Vdc auxiliary power supply must be used for:
Ue 57.5...109 Vac in single phase functioning
16 Hz rated frequency application
Modbus RTU Communication
The ATS022 has two sensors to monitor two power lines; both sensors are able to work with single
phase or three-phase lines. The status of ATS022 can be monitored through the Modbus RTU
connection. The ATS022 has a graphic display where the user is able to check the settings and get all
the information about status of the ATS022.
2.2 Functions of automatic transfer switch ATS022
2. Product overview
Figure 2.4 ATS022 have the capability to monitor two three-phase power lines, both able to work
with single phase, too.
LINE 1 LINE 2
L1 L2 NL3
1
4
3
2LN1
L1
L2
N
L3
X11
L1 L2 NL3
X12
1
4
3
2
LN2
L1
L2
N
L3
KA00426
LINE 1 LINE 2
NL1
1
4
3
2
L1
N
X11
L1 N
X12
1
4
3
2
L1
N
KA00425
TEST
CB1 CB2
KA00344

9
1SDH000760R0002, L4106
Installation and operating instructions, ATS022
2. Product overview
The device has an external auxiliary power supply possibility for guarantying an uninterrupted power
supply for the protection devices in the case where they are not powered through the control circuit.
From the display, one can choose whether the N-line is connected or not.
Figure 2.6 The circuit diagram, when N-line is not connected.
Figure 2.5 An external 24...110 Vdc auxiliary power supply
LINE 1 LINE 2
L1 L2 L3
1
4
3
2LN1
L1
L2
L3
X11
L1 L2 L3
X12
1
4
3
2
LN2
L1
L2
L3
KA00468
1
2X41
AUX
LINE 1 LINE 2
L1 N
1
4
3
2LN1
L1
L2
N
L3
X11
L1 N
X12
1
4
3
2
LN2
L1
L2
N
L3
KA00467
1
2X41
AUX
LINE 1 LINE 2
L1 L2 NL3
1
4
3
2LN1
L1
L2
N
L3
X11
L1 L2 NL3
X12
1
4
3
2
LN2
L1
L2
N
L3
KA00466
1
2X41
AUX

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
10
3. Description
3.1 ATS outputs
3.1.1 Opening/closing command to circuit breakers, DO1...DO4
The output relays command the circuit breakers to open and close its releases. The configuration of the
output relays has been designed to allow the command of any type of motor operator through a direct
connection.
The device has been integrated with the automation logic to guaranty the highest-level safety for
commanding the circuit breakers.
To do that, the automation logic monitors the correct operation of the circuit breaker after a command
has been sent. If the feedback of the CB status is not received within 5 seconds of the sending of the
command, the device considers it as a failed command and operates as follows:
An alarm is generated: DO6 and DO9 activate.
Alarm LED switches on.
Alarm is set off by pushing the RESET key. After that the device is always in the Manual Mode to
prevent unwanted operation of the circuit breaker.
Exactly the same operations are performed for the protection device on the emergency line during the
back-switching sequence.
3.1.2 Gen-Set start/stop, DO5
Gen-Set start and stop is handled by a bistable relay. When the relay is active on DO5 Start X23:1, the
generator is started. When the relay is active on DO5 stop X23:3, the generator is stopped.
3.1.3 Alarm signaling, DO6
This contact is closed when the automatic transfer switch logic is active. If the contact is closed, it
means the logic is disabled and an alarm is generated.
3.1.4 Protection device alarm signaling, DO9
This contact is closed when opening or closing CB fails.
3.1.5 Auto/Manual signaling, DO10
This contact is closed when the operating mode is Manual.
3.1.6 Disconnection Secondary Loads, DO11
See page 32.
3.2 ATS inputs
3.2.1 CBs status Input, DI1, DI2
Two inputs are connected to the normal and emergency line circuit breakers auxiliary contacts
(CB open = open contact).
Please, check the rated voltages allowed for motor operators!
3. Description

11
1SDH000760R0002, L4106
Installation and operating instructions, ATS022
3.2.2 CB Withdrawn
In the case of withdrawable circuit breakers, the auxiliary contacts for the CB inserted are connected
to these inputs (withdrawn=open contact). In the case of a withdrawn circuit breaker, the transfer
switch logic is disabled (DO6 activated, Alarm LED is ON) and the unit goes in the Manual Mode (DO10
activated, Auto LED is OFF). When a CB is re-inserted, the logic is enabled (DO6 disactivated, Alarm LED
is OFF) and the ATS022 is in the Manual Mode (DO10 activated, Auto LED is OFF).
To set the ATS022 in the Automatic Mode the RESET key must be pushed (DO10 disactivated, Auto LED
is ON).
3.2.3 CB Trip, DI4, DI5
The signalling contacts for tripping the normal and emergency line circuit breakers are wired to these
inputs. In the case of CB tripping, the automation logic is disabled (DO6 activated, Alarm LED is ON).
After resetting the signals of CBs trip the logic is enabled again (DO6 disactivated, Alarm LED is OFF).
3.2.4 Gen-Set Alarm, DI8
A Gen-set alarm prevents switching to the emergency line. In the case of the power supply from the
emergency line, when an alarm occurs, ATS022 keeps the line 2 with logic OFF; to enable the logic the
alarm must be reset.
This input can be used to wire several alarms coming from the Gen-set in parallel: oil pressure loss, over
temperature, etc.
An alarm is signaled by the Alarm LED on the front of the device, and the relative electrical contact is
closed.
3.2.5 Forced switching to the emergency supply line, DI9
Some short-period industrial processes require power supplied from a Gen-Set rather than normal line
power, to avoid any possible supply anomalies and to guarantee a higher level of reliability.
Forced switching to the emergency line can be easily carried out keeping this input closed (only in the
Automatic Mode).
This operation starts the complete transfer to the emergency line switching procedure:
Gen-Set start
Normal line circuit breaker opening
Emergency line circuit breaker closing
The power supply from the emergency line remains as long as this command is active. When the
command is disarmed, the reverse transfer to the normal supply line switching procedure is started.
3.2.6 Switching logic enable/disabled, DI3
When this input is closed, the switching logic is enabled. The function is used for integrating general
alarms originating from the plant.
3.2.7 The command to startup the generator, DI10
When this input is activated the generator is started.
3.2.8 Third CB status input, DI11
This input is connected to the bus tie circuit breaker auxiliary contact.
3. Description

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
12
3. Description
TS TCE TBS TCN TGOFF
TS = Switching delay, 0...30 s
TCE = Close emergency delay, 0...60 s
TBS = Back switching delay, 0...30 s
LINE 1 OK
CB1 CLOSED
GEN. START
GEN. START
LINE 2 OK
CB 2 CLOSED
KA00485
TCN = Close normal delay, 0...60 s
TGOFF = Generator stop delay, 0 s, 1 s, ...59 s, 1 min, 2 min, ...5 min
Figure 3.1 Automatic Switching Sequences
3.3 Application scenarios
The ATS022 can be used in different installation scenarios:
Two transformer incoming lines
One transformer incoming line and an emergency generator on the emergency line
3.2.9 Voltage sensors input
Voltage sensors are the same on the normal and emergency lines.
The net sensor is able to detect the following anomalies:
Undervoltage and overvoltage
Phase loss
Voltage imbalance
Minimum and maximum frequency
The net sensor monitors the normal supply line in order to start the switching procedure from the normal
to the emergency line in the case of network anomalies. Equally, the net sensor enables the reverse
switching procedure when the normal supply line returns.
3.2.10 Measurements
Voltage: 1 %
Frequency: 1 %

13
1SDH000760R0002, L4106
Installation and operating instructions, ATS022
3. Description
Figure 3.2 Two transformer oncoming lines
In this case, the installation scenario is the following: ATS is connected to two power incoming lines.
Both lines are the secondary section of a medium-low voltage transformer or in any case, there are two
lines normally present. One of the two lines has more importance; it is normally used to supply the plant.
The second line is an emergency line; it is used in case of an emergency.
In standard conditions, the ATS022 monitors the normal line, analyzing whether the voltage, frequency,
and phase balance are correct. If one of these values is out of the set threshold, after a time delay TS the
ATS022 sends an opening command to the protection device on the normal line. If the emergency line
is OK, the closing command to the protection device on the emergency line is executed after a set time
delay (TCE). In the same way, the ATS022 will control the back-switching sequence when the normal line
will restart properly working:
If Line 1 (= the normal line) comes back, after the set time delay (TBS) the ATS022 sends an opening
command to the protection device on the emergency line and the closing command to the protection
device on the normal line is executed after a set time delay (TCN).
The switching sequence can be summarized in the following steps:
An anomaly occurs on the normal line
Delay time TS
Opening the protection device on the normal line
Delay time TCE
Closing the protection device on the emergency line
The back-switching sequence can be summarized in the following steps:
The normal line will restart properly working
Delay time TBS
Opening the protection device on the emergency line
Delay time TCN
Closing the protection device on the normal line
Many anomalies can occur during both sequences:
a) Tripping any of the two protection devices
The ATS022 is connected with the digital trip signalling contacts (DI4, DI5) of the two protection devices.
An active trip signal will lock the switching logic in ATS022.
The Alarm LED will be switched ON to indicate an active alarm (DO6 activated). To reset this condition,
the protection device must be reset by pushing the RESET key. After resetting the device the logic is
enabled (DO6 disactivated, Alarm LED is OFF).
KA00428
3.3.1 Two transformer incoming lines

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
14
Figure 3.4 Logic operation when opening command is OK
Closing Command
During the switching sequence ATS022 sends the closing command to the protection device on
emergency line. If this is not effectively closed in five seconds, the “Close 2 Failure” alarm is activated
and the Alarm LED will be switched ON. This alarm will lock the switching logic and can only be reset by
pushing RESET key.
3. Description
Figure 3.5 Logic operation when closing command fails
KA00394
5 s
CB2 status
Alarm
Closing CB2
KA00390
Under 5 s CB1 status
Alarm
Opening CB1
Figure 3.3 Logic operation when opening command fails
KA00389
5 s
CB1 status
Alarm
Opening CB1
b) Protection devices do not respond
Opening Command
During the switching sequence, the ATS022 sends the opening command to the protection device on
the normal line. If this is not effectively opened in five seconds, the “Open 1 Failure” alarm is activated
and the Alarm LED will be switched ON. This alarm will lock the switching logic and can only be reset by
pushing the RESET key.

15
1SDH000760R0002, L4106
Installation and operating instructions, ATS022
3. Description
Figure 3.7 Transformer on normal line and generator on emergency line
In this scenario, the ATS022 works in the same way as the previous one. The main difference is that it
also manages the status of the generator.
3.3.2 Transformer on normal line and generator on emergency line
Figure 3.6 Logic operation when closing command is OK
KA00395
Under 5 s CB2 status
Alarm
Closing CB2
G
KA00427
If the auxiliary power is used the device doesn’t go to the powersave.
c) Missing of both lines
The missing of both lines is indicated by a blinking Power LED. In this case, the ATS022 will be in a
power saving state. If both lines are missing more than one minute, the ATS022 will shut down.
If the normal line or the emergency line comes back supplying the ATS022 in Auto Mode, it will analyze
the conditions of the monitored lines and the status of the two protection devices (or the position of the
circuit breaker) and it will switch on the line that is OK giving priority to the normal line.
If the ATS022 is in Manual mode before the voltage drop, it cannot change its state, although the voltage
comes back to the other line.

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
16
3. Description
The switching sequence will be the following:
An anomaly on the normal line occurs
Delay time TS
Start command to the generator
Emergency line OK
Opening of the protection device on the normal line
Delay time TCE
Closing of the protection device on the emergency line
Meanwhile the back-switching sequence will be:
Normal line OK
Delay time TBS
Opening of the protection device on the emergency line
Delay time TCN
Closing of the protection device on the normal line
Delay time TGOFF
Stop command to the generator
Of course the same anomalies in the previous scenario can occur, and in these cases the same
operations are performed, but the following must be considered.
Generator alarm
If the generator alarm input DI8 is activated, the Alarm LED will be switched ON and an alarm message is
shown in the Alarm log of the device (DO6 activated, logic disabled).
3.3.3 Special scenarios
The new ATS022 has to be developed to be compliant with special applications too, in details:
No Line Priority: in this scenario, none of the two lines is of outmost importance. That means that after
switching the ATS022 remains on the selected power supply line although the previous line starts to work
properly. The logic of the switching is the same as in other scenarios. The only difference is that in this
scenario, there is not a back-switching sequence. This condition has to be set via the Line Priority menu
page.
Two transformers and bus tie (Managing secondary loads): In this scenario, the ATS022 has to be
able to control a third protection device used by the bus tie. ATS022 acquires the open/closed status of
this device with digital input DI11 and by activating DO11 ATS022 is able to disconnect the secondary
loads.

17
1SDH000760R0002, L4106
Installation and operating instructions, ATS022
4. Operating
Before using of the automatic transfer switch ATS022, read carefully chapter 1 “Safety notes” in order to
avoid malfunctions or dangerous operating conditions.
4.1 Automatic transfer switch ATS022 in Manual Mode
Selecting the automatic transfer switch ATS022 to the Manual Mode:
a. Make sure that power LED is ON, see the Figure 4.1/j.
b. If Auto LED is OFF /k, the automatic transfer switch is in Manual Mode.
c. If the Auto LED is ON, push the RESET key once /l. The Auto LED switches to OFF and the
automatic transfer switch ATS022 is in Manual Mode /m.
Figure 4.1 Selecting the automatic transfer switch ATS022 to Manual Mode
Never open any covers on the product. There may be dangerous external control
voltages inside the ATS022 automatic transfer switch even if the voltage is turned off.
Exercise sufficient caution when handling the unit.
Never handle control cables when the voltage of the ATS022 automatic transfer switch
or external control circuits are connected.
4. Operating
OR
KA00345
Manual mode
Manual mode
!
TEST
CB1 CB2
!
1 2
2 3 4

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
18
To select the operating line by the automatic transfer switch ATS022 in Manual Mode:
a. Push the appropriate CB1 or CB2 key
b. When pushing the CB1 key (see the Figure 4.2/k), the circuit breaker CB1 will be in the ON position
(the status and the line indication, see the Figure 4.2/l) and the circuit breaker CB2 will be in the
OFF position. If the circuit breaker CB1 is already in the ON position, pushing the CB1 key opens
the circuit breaker.
c. When pushing the CB2 key, the the circuit breaker CB2 will be in the ON position and the circuit
breaker CB1 will be in the OFF position.
e. If you push the CB1 key while the circuit breaker CB2 is in the ON position, nothing happens.
Before pushing the CB1 key, you have to push the CB2 key to open the circuit breaker CB2.
Figure 4.2 Selecting the operating line, the circuit breaker status and the chosen line indication in
display terminal in ATS022
4. Operating
TEST
CB1 CB2
KA00346
CB1
CB1 CB2
CB1 CB2
1
3
2

19
1SDH000760R0002, L4106
Installation and operating instructions, ATS022
Figure 4.3 Manual Mode control
4.2 Automatic transfer switch ATS022 in Automatic Mode
Selecting the automatic transfer switch ATS022 to the Automatic Mode:
a. Make sure that power LED is ON, see the Figure 4.4/j.
b. Push the RESET key once /k.
c. If Auto LED is ON, the automatic transfer switch is in Automatic Mode /l.
d. If the Auto LED is OFF, push the RESET key again /m, the Auto LED switches to ON /nand the
automatic transfer switch is in Automatic Mode.
Figure 4.4 Selecting the automatic transfer switch ATS022 to Automatic Mode
4. Operating
CB1
Protection
device on line 1
Protection
device on line 2
CB1-command CB1-command CB2-command
Closed
Closed
Open
Open
CB1 CB2
KA00423
KA00347
OR
!
TEST
CB1 CB2
Automatic mode
TEST
CB1 CB2
!
Automatic mode
1 2 3
345

Installation and operating instructions, ATS022
1SDH000760R0002, L4106
20
4. Operating
4.3 TEST sequence
When pushing the TEST key, the automatic transfer switch (ATS022) enters the test sequence in which
it is possible to simulate switching and back-switching sequences step-by-step, by pressing the TEST
key. ATS022 must be in MANUAL mode before entering the test sequence. Exiting from test sequence is
done by RESET key.
Steps in the TEST sequence are:
1. Press TEST; generator starts (skipped if the generator is not in use)
2. Press TEST; Open CB1
3. Press TEST; Close CB2
4. Press TEST; Open CB2
5. Press TEST; Close CB1
6. Press TEST; stop generator (skipped if the generator is not in use)
Pressing TEST after that; sequence restarts. Alarms are activated in the same way as in automatic
sequences, if circuit breaker control fails. The user can stop the TEST sequence by pressing the RESET
key. After stopping the TEST sequence the device returns to the default page and the settings are
exactly the same as they were before starting the TEST sequence.
Figure 4.5 TEST sequence to simulate the functions
KA00354
TEST
CB1 CB2
Before starting the TEST sequence, please, make sure that CB1 is in closed position
and the both lines have the voltage on.