Abilica XC 2700 MILL V4 User manual

1
ABILICA XC 2700 MILL V4
USER’S MANUAL

2
PRODUCT OVERVIEW
Console
Bottle holder
Front handrail
Safety Key
Left Handrail
Running belt
End cap
Back main frame
Back base frame
Side rail
Right handrail
38 Roller
Front pedestal
Front frame
Quick switch
Motor cover

Note: Some bolts may be pre-installed.
Illustrasjon
Nr.
Engelsk navn
Ant.
D31
Hex round head bolt M8*20 mm
25
D33
Hex round head bolt M8*60 mm
2
D6
Round hex bolt M8*50 mm
2
E12
Round hex bolt M8*30 mm
16
D52
Cross bolt ST4.2*16mm
7
D66
D67
Small Curved Washer M8
Large Curved Washer M8
2
1
D23
Flat washer M8
26
D25
Spring washer M8
26
D15
Cap Nut
2
D2
D92
Allen wrench 6mm
Allen wrench 8mm
1
1
D3
Allen wrench 5mm
1
D1
Cross wrench 13-15-17
1
HARDWARE
b

4
Main frame 1pc
A3L Left handrail 1pc
A3R Right handrail 1pc
C13 Safety Key 1pc
A4 Front handrail 1pc
B18 Silica gel 1pc
B16 Water bottle holder
2pcs
C15 Power cable 1pc
B1 console 1pc
B2 Plug 8pcs
ASSEMBLY PARTS

5
STEP 1
Tilt the wooden case to upright position.
ASSEMBLY INSTRUCTIONS
Remove all parts from packaging before you start assembling.

6
STEP 2
You will find two transport wheels (E13) with brakes (E14) underneath the wooden case.
The breaks must be released before moving the case.
E14
E13
E14
E13

7
STEP 3
After moving the case to the desired position, lay it down as per the illustration. Cut the strap (E15),
and remove connecting pads (E16/E18) to remove the wooden case.
E15
E16
E17
E18 E17

8
STEP 4
Remove and save the fixing bracket (E2), nylon lock nut M8 (E4), transport wheel (E1) and round
hex bolt M8*85 (E3) from the wooden case.
Note: Save the transport wheels (E1/E13), fixing bracket (E2), nylon lock nut M8 (E4), round hex
bolt M8*85 (E3). These will be used to move the treadmill.
E3
E1
E4 E2
E3
E13
E4
E2
E3
E1
E4 E2
E3
E13
E4
E2

9
STEP 5
Remove the hex round bolt M8*40 (E7), hex round head bolt M8*95 (E11), washer M8 (E8), flat
washer M8 (E9) and nut M8 (E10) from upper/lower foot frame (E5/E6), and lift out the main frame.
E10
E9
E6 E7
E7
E5
E8
E9
E10 E7
E8
E9
E10
E8
E10
E9
E7
E8

10
STEP 6
Connect the left bar (A3L) to the main frame (A1a/b) using hex round head bolts M8*20mm (D31),
spring washers M8 (D25) and flat washers M8 (D23). Attach the right bar (A3R) to the main frame
the same way. Note: start all bolts before you tighten them.
D31
D25D23
D25
D23
D25
D23
D25
D25
D23
D23
D31
D31
D31
D31
D25
D25
D25
D25
D25
D25
D23
D23
D23
D23
D23
D23
A3L
A3R
A1a
D31
A1b

11
STEP 7
Attach plugs (B2) to the bottom of left and right bars (A3L/R).
B2
B2
B2
A3L
A3R
B2
B2
B2
B2

12
STEP 8
Connect the lower wire’s white connector (C17) to the middle wire’s white connector (C18).
STEP 9
Connect the quick switch’s back wire’s black connector (41) to the quick switch’s middle wire’s
black connector (C42) and the middle wire’s black connector (C18).
STEP 10
Attach the front handrail (A4) to the left and right handrails (A3L/R) using hex bolt M8*50mm (D6),
small curved washer M8 (D66) and cap nut (D15).
A3L
A3R

13
STEP 11
Attach the 38 roller (C39) to left and right bar (A3L/R) using hex round head bolt M8*60mm (D33),
spring washer M8 (D25) and flat washer M8 (D23).
A3R
A3L
D33
D23
D23
D33
C39
D25
D25

14
STEP 12
Attach the iron fixing plate (A37) to the front handrail (A4) using round hex bolt M8*20mm (D31)
and large curved washer (D67).
STEP 13
Guide the emergency switch’s upper wire’s black connector (C43) and the console’s upper wire’s
white connector (C16) through the hole in the iron fixing plate (A11).

15
STEP 14
Attach the console (B1) to the iron fixing plate (A11) using the cross bolt ST4.2*16mm (D52).

16
STEP 15
Attach bottle holders (B16), safety key (C13) and power cable (C15).
B16
B16
C13
C15
Assembly is completed.

17
Transport wheel assembly：
Should you need to move the treadmill, it can be moved more easily by attaching the wheels that
came with the wooden case. Place the fixing bracket (E2) onto upper and lower foot (E6/E5), and
attach the transport wheels (E1/E13) to the fixing bracket using hex round head bolt M8*20mm
(E12) and nylon lock nut M8 (E4).
Push the treadmill to desired position, and remove the transport wheels. Alternatively, you can
attach two wheels on the front of the treadmill, and lift the back.
TREADMILL TRANSPORT WHEEL ASSEMBLY
E12
E12
E12
E12
E13
E1
E1
E1
E2
E5
E6
E6
E4 E2
E4
E2
E4

18
Lubrication
Apply 10 ml of the the included oil on the sponge end of the included lubrication stick. Insert the
stick underneath the running belt with the oily sponge facing down towards the wooden board. Start
by the motor hood and run the stick in a zigzag pattern halfway down the deck. Apply another 10 ml
of the included oil to the lubrication stick, and repeat the procedure. Then, set the running belt to
move at a speed of 5 kph for five minutes.
Cleaning
After 100 hours of use, drag the lubrication stick underneat the running belt from top to bottom. Use
the end of the stick that has not previously been used for oiling the running belt. Then, apply 10 ml
of the included oil to the lubrication stick, and apply oil to the running belt as described above.
Repeat for ever 100 hours of use. Should the treadmill stop on its own accord, it could be in need of
lubrication.
THE TREADMILL MUST BE LUBRICATED BEFORE USE

19
STEP 1
Remove the console (B1) and the adjustment guide (A12) by unscrewing the scoket head cap bolt
M8x20 (D31), large curved washer M8 (D67), Socket head cap bolt M6x16 (D5), flat washer M6
(D22), spring washer M6 (D11) as shown on the illustration.
1
CONSOLE POSITION CHANGE

20
STEP 2
Place the console (B1) and adjustment guide (A12) on the right handrail (A3R) and attach using
socket head cap bolt M8x20 (D31), large curved washer M8 (D67), socket head cap bolt M6x16
(D5), flat washer M6 (D22) and spring washer M6 (D11) as shown on the illustration.
2