Abus TVAC19100B User manual

TVAC19100B

User guide

Betjeningsvejledning

Instrukcja obsługi
E
Manual de instrucciones
S
Bruksanvisning

Инструкция по эксплуатации
Version 03/2015

This user guide contains important information on starting operation and using the device.
Make sure that this user guide is handed over when the product is given to other persons.
Keep this user guide to consult later.
For a list of contents with the corresponding page numbers, see page 7.
Denne betjeningsvejledning indeholder vigtige henvisninger til idriftsættelse og
håndtering. Vær også opmærksom på dette, hvis produktet gives videre til en tredje person.
Opbevar derfor denne betjeningsvejledning til senere brug!
Indholdet kan ses med sideanvisninger kan findes i indekset på side 30.
Niniejsza instrukcja obsługi zawiera ważne wskazówki dotyczące uruchamiania i obsługi.
Pamiętaj o tym, także przekazując produkt osobie trzeciej.
Zachowaj instrukcję do wykorzystania w przyszłości!
Spis treści wraz z numerami stron znajduje się na stronie 53.
Este manual de instrucciones contiene indicaciones importantes para el manejo y la puesta en
funcionamiento del producto. Téngalas también en cuenta si entrega la máquina a terceros.
Por ello, consérvelas en un lugar adecuado para su posterior lectura.
En el índice de la página 76 encontrará un listado de los contenidos con las páginas donde podrá
consultarlos.
Denna bruksanvisning innehåller viktiga anvisningar för idrifttagande och
användning.
Dessa anvisningar ska observerad även om denna produkt överlämnas till tredje part.
Förvara denna bruksanvisning för framtida referens!
På sidan 99 finns finns en innehållsförteckning med sidoreferenser.
Данная инструкция по эксплуатации содержит важные указания по вводу в
эксплуатацию иобращению спродуктом.
Примите это во внимание, также при передаче продукта впользование третьим лицам.
По этой причине сохраните данную инструкцию для повторного прочтения!
Вся информация отражена вСодержании суказанием соответствующих номеров страниц на
Странице 122.
English
Dansk
Español
Polski
Svenska
Русский
2

TVAC19100B
User manual
Important information and FAQs about this product and other
products can be found on the website
www.abus.com/eng/Self-installed-security
Version 02/2015
English translation of the original German user manual.
Retain for future reference.

English
Introduction
Dear Customer,
Thank you for purchasing this product.
This device complies with the requirements of the applicable EU directives. The declaration of
conformity can be obtained from:
ABUS Security-Center GmbH & Co. KG
Linker Kreuthweg 5
86444 Affing
GERMANY
To ensure this condition is maintained and that safe operation is guaranteed, it is your obligation to observe
this user manual.
Read the entire user manual carefully before putting the product into operation, and pay attention to all
operating instructions and safety information.
All company names and product descriptions are trademarks of the corresponding owner. All
rights reserved.
If you have any questions, please contact your specialist installation contractor or specialist dealer.
Data storage is subject to national data privacy guidelines.
Warning as required by §201 StGB (German Criminal Code):
Whosoever unlawfully makes an audio recording of the privately spoken words of another; or uses, or
makes a recording thus produced accessible to a third party, shall be liable to imprisonment or a fine.
Whosoever unlawfully overhears with an eavesdropping device the privately spoken words of another
not intended for his attention; or publicly communicates, verbatim or the essential content of, the
privately spoken words of another, recorded or overheard, shall incur the same penalty.
Disclaimer
This user guide has been produced with the greatest of care. Should you discover any missing
information or inaccuracies, please contact us under the address shown on the back of the manual.
ABUS Security-Center GmbH does not accept any liability for technical and typographical errors, and
reserves the right to make changes to the product and user guide at any time and without prior
warning.
ABUS Security-Center GmbH is not liable or responsible for direct or indirect damage resulting from the
equipment, performance and use of this product. No forms of guarantee are accepted for the contents of
this document.
4

English
Explanation of symbols
The triangular high voltage symbol is used to warn of the risk of
injury or health hazards (e.g. caused by electric shock).
The triangular warning symbol indicates important notes in this user manual which must
be observed.
This symbol indicates special tips and notes on the operation of the unit.
Important safety information
All guarantee claims are invalid in the event of damage caused by non-compliance with
this user manual. We cannot be held liable for resulting damage.
In the event of material or personal damage caused by improper operation or non-
compliance with the safety information, we cannot be held liable. All guarantee claims
are void in such cases.
This device has been manufactured in accordance with international safety standards.
Please read the following safety information carefully.
Safety information
1. Power supply
Only operate this camera through a power source which supplies the mains voltage specified on the
type plate. If you are unsure of the installation location's power supply, contact your power supply
company. Disconnect the device from the mains power supply before carrying out maintenance or
installation work.
2. Overloading
Avoid overloading electrical sockets, extension cables, and adapters, as this can result in fires or
electric shocks.
3. Cleaning
Only use a damp cloth to clean the camera. Do not use corrosive cleaning materials.
Disconnect the device from the power supply before cleaning.
4. Ventilation
The camera's ventilation openings must not be covered or obstructed.
Ensure that no objects penetrate the device, e.g. through the ventilation openings.
5. Accessories
Only connect devices expressly designed for use with the camera. Otherwise hazardous situations or
damage to the device may result.
6. Installation location
This device can be used in inside as well as outside.
Do not place the camera in close proximity to heaters, ovens or other heat sources, or in direct
sunlight. Only operate the device in locations with temperatures within a permissible ambient
temperature range of -10° to ~50°C.
5

English
Warnings
Observe all safety and operating instructions before putting the device into operation for the first time.
1. Observe the following information to avoid damage to the power cable and plug:
•Do not modify or manipulate the power cable or plug.
•Do not pull the cable when disconnecting the device from the power – always take hold of the
plug.
•Ensure that the power cable is positioned as far away as possible from any heating
equipment, to avoid melting the plastic coating.
2. Follow these instructions. Non-compliance with these instructions could lead to an electric shock:
•Never open the housing or power supply unit.
•Do not insert any metallic or flammable objects into the device.
•Use surge protection to prevent damage caused by overvoltage (e.g. in electrical storms).
3. Disconnect defective devices from the power supply immediately and contact your specialist dealer.
If in doubt, have a specialist technician carry out assembly, installation and connection of the
device. Improper or unprofessional work on the power supply system or domestic installation
puts both you and other persons at risk.
Connect the installations so that the mains power circuit and low-voltage circuit always run
separately from each other. They should not be connected at any point or become connected
as the result of a malfunction.
Avoid the following adverse conditions during operation:
•moisture or excess humidity
•temperatures outside of the permissible range
•direct sunlight
•dust or flammable gases, vapors or solvents
•strong vibrations
•strong magnetic fields (e.g. next to machines or loudspeakers)
Unpacking the device
Handle the device with extreme care when unpacking it.
If the original packaging has been damaged, you must start by inspecting the device. If the
device shows signs of damage, return it in the original packaging and inform the delivery
service.
6

English
Contents
1. Intended use.................................................................................................................................... 8
2. Scope of delivery............................................................................................................................. 8
3. Features and functions.................................................................................................................... 8
4. Device description ........................................................................................................................... 9
4.1. Overview.................................................................................................................................. 9
4.2. Camera description ................................................................................................................. 9
5. Installation...................................................................................................................................... 10
6. Operation and configuration via app.............................................................................................. 12
7. Maintenance and cleaning............................................................................................................. 23
7.1. Maintenance.......................................................................................................................... 23
7.2. Cleaning................................................................................................................................. 23
8. Disposal......................................................................................................................................... 23
9. Tips for troubleshooting................................................................................................................. 24
10. Technical data ........................................................................................................................... 25
7

English
1. Intended use
The day & night PnP IP camera enables high-quality monitoring. This camera is designed for
indoor or outdoor installation. The built-in infrared LEDs enable day and night monitoring of object
distances up to a maximum of ten meters away.
Since the camera features protection class IP66, it can be used both indoors and outdoors.
The camera is easy to configure and operate using the app, meaning that it can be accessed
anywhere in the world.
For a detailed functional description, see Chapter "3. Features and functions".
2. Scope of delivery
Wi-Fi outdoor camera & app
Power supply unit including EU, Australian
and
UK adapters
5 V DC/1.5 A
LAN adapter cable Camera mount including mounting material
Antenna
3. Features and functions
•for effective all-round monitoring of interior spaces
•compact IP66 outdoor camera with infrared night vision function
•guided step-by-step installation via app (iOS, Android)
•HD 720p resolution and infrared night vision function for brilliant image quality
•recording on microSD card
8

English
4. Device description
4.1.Overview
Item number TVAC19100B
Resolution 720p
IR LEDs 
IR swivel filter (ICR) 
Operational voltage 5 V DC
4.2.Camera description
Front:
Antenna
Status LED

Fixed lens

IR LED
Camera mount
PIR sensor
Power LED
9

English
Rear:
5. Installation
Using the camera mount, select a suitable installation site. Mark the drilling holes on the surface
and drill the holes. First, insert the supplied screw anchors and attach the mount using the screws.
You can swivel the mount by up to 90° to select the desired position. First, loosen the screw at the
side and adjust the camera to the desired angle of view. Next, tighten the screw to fix the camera in
the desired position.
Antenna connection
Micro SD card slot
Power cable/reset
button
10

English
Then screw the camera onto the mount and connect the power supply unit to the camera.
Installation options:
Ceiling installation Wall installation
11

English
6. Operation and configuration via app
The TVAC19100 Wi-Fi outdoor camera & app gives you the option of switching to live on the
cameras and to configure the recorder. The app for this device can be found in the App Store
under the name of “App2Cam”.
To configure access to the camera, proceed as follows:
①
Set-up – preparation
Download the "App2Cam" app and install it on your
smartphone.
Check that your smartphone or tablet is connected to
the Internet.
There are two ways to connect the camera to the
network:
Option 1: (Wireless set-up)
Connect the enclosed power supply unit to the camera.
Do not start to set up the camera until both LEDs light
up. This may take around 60 seconds.
Option 2: (Wired set-up)
Connect the LAN adapter cable provided to the camera.
Connect the cable to your router in the next step.
Then connect the enclosed power supply unit.
Do not start to set up the camera until both LEDs light
up. This may take around 60 seconds.
12

English
②
Set-up – iOS app
Please note that the iOS app and the Android app
require different setup processes. If you have an
Android device, please refer to the
set-up process described in
③
.
Open the WLAN settings in your iOS device and
connect to the camera's HD-XXXXXX network.
The camera's WLAN password is "12345678".
Launch the app and select the desired type of set-up.
Option 1: (Wireless set-up)
The camera is added automatically. Click on "Live
view".
The app will now ask you to select the connection type
for the camera.
WLAN
Select your WLAN network in the drop-down list, enter
your WLAN key and click "OK".
Please wait 90 seconds for the camera to restart and
connect to your WLAN network. Make sure your mobile
device reconnects to your WLAN network.
AP mode
The camera remains in access point mode and can still
be reached via this mode. To do this, connect to the
camera's access point. The WLAN password for the
camera is "12345678" and cannot be changed.
Installing several cameras using "wireless set-up" can
lead to faults. Please install only one device at a time.
13

English
Option 2: (Wired set-up)
Give the camera an appropriate name.
For automatic registration of the DID, click "Search".
The DID of the camera which is currently connected to
the router via a network cable is now displayed. Select
to accept this DID. Alternatively, you can enter the DID
manually.
Then enter the security code (standard: "123456") and
add the camera by clicking "Save".
This camera is now locally accessible on your network.
To connect the camera to a WLAN network, please go
to
menu option
⑫
.
③
Set-up – Android app
Please note that the Android app and the iOS app
require different setup processes. If you have an iOS
device, please refer to the
set-up process described in
②
.
Launch the app on your smartphone or tablet and click
"Add new camera".
Then select the desired type of set-up.
Option 1: (Wireless set-up)
The app will search for an available HD-XXXXXX
network, transmitted by the camera, and will
automatically connect your smartphone to it.
If connecting manually to the HD-XXXXXX network, use
the WLAN password "12345678".
Once the search has been successfully completed,
click on "Live view".
The app will now ask you to select the connection type
for the camera.
WLAN
Select your WLAN network in the drop-down list, enter
your WLAN key and click "OK".
Please wait 90 seconds for the camera to restart and
connect to your WLAN network. Make sure your mobile
device reconnects to your WLAN network.
14

English
AP mode
The camera remains in access point mode and can still
be reached via this mode. To do this, connect to the
camera's access point. The WLAN password for the
camera is "12345678" and cannot be changed.
Installing several cameras using "wireless set-up" can
lead to faults. Please install only one device at a time.
Option 2: (Wired set-up)
Give the camera an appropriate name.
For automatic registration of the DID, click "Search".
The DID of the camera which is currently connected to
the router via a network cable is now displayed. Select
to accept this DID. Alternatively, you can enter the DID
manually.
Then enter the security code (standard: "123456") and
add the camera by clicking "Save".
This camera is now locally accessible on your network.
To connect the camera to a WLAN network, please go
to
menu option ⑫.
④
Connection status
Once you have successfully added your camera, the
name of your camera and the current connection status
will appear in the overview. The image displayed is the
last video image displayed during the previous session.
You can add to up to eight cameras in the app.
Tap your chosen camera and you will be taken to the
live view.
The first time you access the live view, the app will
prompt you to change the security code. This is
automatically applied to the camera's settings.
System name
e.g. Test
Connection status
Connected = you are connected to your system
Disconnected = there is no connection to the system
15

English
Adding a camera
This lets you add another
system.
Camera configuration
This will display the camera configurations.
Camera settings
Remove a camera
Access recordings on the SD card
Press to return to connection status.
Updating connection
The connection is being updated.
PIN code/Push settings/
Instructions/Firmware information
Here you can store a PIN code, activate or
deactivate push notifications, view the
instructions for your camera as a PDF or view
the firmware version of the app.
⑤
Store PIN code
To store a PIN code for this app, proceed as follows:
Open "Set PIN lock" in .
Enter a four-digit PIN code and then confirm it.
Tick "Activate lock on startup".
If you have stored a PIN code, you will be asked to
enter it as soon as you open the app.
16

English
⑥
Live view
Select the desired camera from the drop-down menu.
You will now see the live image from the camera. The
image is displayed in 4:3 mode; to display a 16:9
format, rotate your mobile device by 90°.
Snapshot
This lets you take a screenshot of your live
image. The image is then saved in your photo
gallery on your mobile device.
The saved images are time-stamped and
saved in the photo gallery.
Audio
This lets you activate or deactivate audio.
Start recording
This lets you start recording manually on the
SD card. The recording time is one minute
and cannot be cut short. The icon appears
during recording.
Back
This takes you back to the camera overview.
You are always shown the last screenshot.
⑦
Settings
Here you can change the camera settings. Email
notifications can also be activated or deactivated.
Email notification
Activating email notification in the event that motion is
detected.
Please note that outdoor video surveillance can give
rise to false alarms.
Click "Advanced settings" to start the configuration.
To access the settings you will need to enter the admin
password (standard: "123456").
17

English
⑧
General settings
Once you have accessed the settings you will be able
to configure the camera.
Admin password
The admin password gives access to the camera
settings. The standard admin password is "123456".
To protect your camera from unauthorized access,
change this password during initial installation.
If you have forgotten your password, you can restore
factory settings on the camera by pressing the Reset
button for five seconds. The red LED will start to flash.
Time zone
Global time zones are listed in the drop-down menu.
Select the time zone in which the camera is being
installed. If the time zone in question uses daylight
saving time, activate daylight saving time.
Daylight saving time
Activate/deactivate daylight saving time.
Device security code
The security code enables the camera to be set up in
the app. The standard security code is "123456".
During initial installation you will always be prompted
to change this security code.
If you have forgotten your security code, you can
restore factory settings on the camera by pressing the
Reset button for five seconds.
18

English
⑨
Video settings
The video settings allow you to change the video quality
and ambient conditions for the camera.
Video quality:
The video quality setting allows you to select the
quality of video streaming.
Better streaming:
The video is displayed more smoothly.
Better image:
The video image is displayed in higher resolution.
HD video:
The video image is transmitted in HD resolution.
However, there may be delays in the image display
as a result of the large volume of data.
Only use the "Better image/HD video" setting if you
have sufficient bandwidth (1 Mbps) and adequate
system requirements, and please be aware that the
different transmission technologies used for audio
and video may result in asynchronous transmission
due to varying network usage.
Image orientation
Here you can rotate or flip the image.
Tilt:
The image is rotated by 180 degrees.
Flip:
The image is flipped.
Tilt & flip:
The image is rotated by 180 degrees and flipped.
Ambient conditions
Here you can select the power frequency inside
(50 Hz), inside (60 Hz) and outside.
Standard value for Germany: 50 Hz
Adjustment to poor light conditions
Adjusting the video image for poor light conditions
in night mode. There are five levels to choose from,
with Level 5 being the brightest.
19

English
⑩
WiFi settings
WiFi settings
In the WiFi settings you can select the desired network
with which the camera should be used for Internet
access.
When the menu item is selected, all the networks within
range will be displayed. Choose your network and enter
your own WiFi password.
To prevent access by unauthorized persons, protect
your network using encryption with WPA/ WPA2/
WPA2-PSK.
After the settings have been saved, restart the camera.
Please do not forget to remove the Ethernet adapter
cable (if it is used during initial installation).
If no connection has been established or if you have
entered the WiFi details incorrectly, press the Reset
button for five seconds to restore factory settings to the
camera.
⑪
Motion detection
The settings for motion detection are necessary for
notification via email or push notification and for motion-
controlled recording.
Detection mode
Here you can select which mode should be used for
notifications.
You have a choice between "Off", “PIR” and "Software".
Off:
No notification/recording if motion is detected.
PIR:
Motion detection is performed by the camera's PIR
sensor
Software:
Motion detection is performed by the camera software.
Here you can define different motion detection
sensitivities for day and night-time. The higher the
sensitivity, the less motion is needed in the image to
trigger motion detection.
20