Abus TVIP91 Series User manual

TVIP91XXX / TVIP92XXX
Version 04/2015
English translation of the original German user manual. Retain for future reference.
TVIP91XXX
TVIP92XXX

56
Introduction
Dear customer,
Thank you for purchasing this product.
This device complies with the requirements of the applicable EU directives. The
declaration of conformity
can be obtained from:
ABUS Security-Center GmbH & Co. KG
Linker Kreuthweg 5
86444 Affing
GERMANY
To ensure this condition is maintained and that safe operation is guaranteed, it is your obligation
to observe this user manual.
Read the entire user manual carefully before putting the product into operation, and pay attention
to all operating instructions and safety information.
All company names and product descriptions are trademarks of the corresponding owner.
All rights reserved.
If you have any questions, please contact your specialist installation contractor or
specialist dealer.
Disclaimer
This user manual has been produced with the greatest of care. Should you discover any
missing information or inaccuracies, please let us know about them.
ABUS Security-Center GmbH & Co. KG does not accept any liability for technical and
typographical errors, and reserves the right to make changes to the product and user manuals
at any time and without prior warning.
ABUS Security-Center GmbH is not liable or responsible for any direct or indirect damage
resulting from the installation, performance and use of this product. No forms of guarantee are
accepted for the contents of this document.

57
Important safety information
All guarantee claims are invalid in the event of damage caused by non-compliance
with this user manual. We cannot be held liable for resulting damage.
In the event of material or personal damage caused by improper operation or non-
compliance with the safety information, we cannot be held liable. All guarantee claims
are void in such cases.
Dear customer,
The following safety information and hazard notes are not only intended to protect your health but
also to protect the device from damage. Please read the following points carefully:
There are no components inside the product that require maintenance by the operator. Opening or
dismantling the product invalidates the CE certification and guarantee claims/warranty.
The product may be damaged if it is dropped, even from a low height.
Avoid the following adverse conditions during operation:
Moisture or excess humidity
Extreme heat or cold
Direct sunlight
Dust or flammable gases, vapours or solvents
Strong vibrations
Strong magnetic fields (e.g. next to machines or loudspeakers)
The camera must not be installed on unstable surfaces.
General safety information:
Do not leave packaging material lying around. Plastic bags, sheeting, polystyrene packaging, etc.
can pose a danger to children if played with.
The video surveillance camera contains small parts which could be swallowed and should be kept
out of reach of children for safety reasons.
Do not insert any objects into the device through the openings.
Only use replacement devices and accessories that are approved by the manufacturer. Do not
connect any non-compatible products.
Please pay attention to the safety information and user manuals for the other connected devices.
Check the device for damage before putting it into operation. Do not put the device into operation if
you detect any damage.
Adhere to the operating voltage limits specified in the technical data. Higher voltages could destroy
the device and pose a health risk (electric shock).
When installing the device in an existing video surveillance system, ensure that all devices
have been disconnected from the mains power circuit and low-voltage circuit.
If in doubt, have a specialist technician carry out assembly, installation and connection of the
device. Improper or unprofessional work on the power supply system or domestic installation
puts both you and other persons at risk.
Connect the installations so that the mains power circuit and low-voltage circuit always run
separately
from each other. They should not be connected at any point or become connected as a
result of a malfunction.

58
Contents
1. INTENDED USE................................................................................................................................... 60
2. EXPLANATION OF SYMBOLS........................................................................................................... 60
3. SCOPE OF DELIVERY........................................................................................................................ 60
4. FEATURES AND FUNCTIONS........................................................................................................... 61
5. DEVICE DESCRIPTION ...................................................................................................................... 62
5.1 OVERVIEW –MODEL NUMBERS .............................................................................................................. 62
5.2 UNPACKING THE DEVICE ........................................................................................................................ 62
5.3 OVERVIEW OF CONNECTIONS,CONTROL ELEMENTS,FRONT/BACK............................................................ 63
6. INSTALLATION................................................................................................................................... 72
6.2 LAYING THE CABLES .............................................................................................................................. 72
6.3 POWER SUPPLY..................................................................................................................................... 73
6.4 ATTACHING THE NETWORK CABLE .......................................................................................................... 74
6.5 ALIGNING THE CAMERA .......................................................................................................................... 74
6.6 ZOOM AND FOCUS SETTINGS.................................................................................................................. 74
6.7 ATTACHING THE OPTIONAL CONNECTING CABLE FOR TVIP9X300 AND TVIP9X700.................................. 75
6.8 SWITCHING INPUT AND SWITCHING OUTPUT.......................................................................................... 75
6.9 STATUS INDICATORS.............................................................................................................................. 76
6.10 CONNECTION INSTRUCTIONS FOR AUDIO INPUT/OUTPUT (TVIP92XXX).................................................. 76
6.11 RESTORING FACTORY SETTINGS (RESET).............................................................................................. 77
6.12 CHANGING THE DOME .......................................................................................................................... 77
7. INITIAL START-UP.............................................................................................................................. 78
7.1 USING THE ABUS IP INSTALLER FOR CAMERA SEARCH ........................................................................... 78
7.2 ACCESSING THE NETWORK CAMERA USING A WEB BROWSER ................................................................... 79
7.2.1 GENERAL INSTRUCTIONS FOR USING THE SETTINGS PAGES................................................................... 79
7.3 INSTALLING A VIDEO PLUGIN ................................................................................................................... 79
7.4 HOMEPAGE (LOGIN PAGE)...................................................................................................................... 81
7.5 USER ACCOUNTS AND PASSWORDS ........................................................................................................ 82
7.6 LINKING UP THE CAMERA WITH ABUS VMS/ABUS VMS EXPRESS.......................................................... 83
7.6 LINKING UP THE CAMERA WITH ABUS NVR/ABUS HYBRID DVR............................................................. 83
7.8 LINKING UP THE CAMERA TO IPCAM........................................................................................................ 83
8. USER MENU "USER" ......................................................................................................................... 84
9. VIEW AND CONFIGURATION MENU USER "MASTER" ................................................................. 86
9.1 ADDING USERS...................................................................................................................................... 88
9.2 VIDEO STREAM SETTINGS....................................................................................................................... 89
9.2 DEACTIVATE/ACTIVATE INSTALLER ACCESS ............................................................................................. 89
9.3 DISPLAYING/DOWNLOADING VIDEO FROM THE INTERNAL MEMORY ............................................................ 90
10. VIEW AND CONFIGURATION MENUS USER "INSTALLER".......................................................... 91
10.1 LIVE VIEW ........................................................................................................................................... 91
10.2 INFO PAGE .......................................................................................................................................... 91
10.3 SETUP WIZARD.................................................................................................................................... 93
10.4 ADVANCED CAMERA SETTINGS ............................................................................................................. 93
10.4.1 VIDEO.............................................................................................................................................. 93
10.4.1.1 GENERAL...................................................................................................................................... 93
10.4.1.2 DAY PROFILE ................................................................................................................................ 93
10.4.1.3 NIGHT PROFILE ............................................................................................................................. 93
10.4.1.4 DAY/NIGHT SWITCHING .................................................................................................................. 94
10.4.1.5 PRIVACY MASKING......................................................................................................................... 94
10.4.1.6 VIDEO STREAM SETTINGS .............................................................................................................. 95
10.4.1.7 NETWORK LOSS RECORDING.......................................................................................................... 96
10.4.2 NETWORK........................................................................................................................................ 97
10.4.2.1 IPV4SETTINGS ............................................................................................................................. 97
10.4.2.2 PORTS.......................................................................................................................................... 97

59
10.4.2.3 DDNS.......................................................................................................................................... 97
10.4.2.4 HTTPS ........................................................................................................................................ 98
10.4.2.5 SMTP/EMAIL ................................................................................................................................ 98
10.4.3 OVERLAY TEXT................................................................................................................................. 98
10.4.4 DATE/TIME ....................................................................................................................................... 98
10.4.5 SYSTEM........................................................................................................................................... 99
10.4.5.1 GENERAL...................................................................................................................................... 99
10.4.5.2 FIRMWARE/RESET......................................................................................................................... 99
10.4.5.3 LOG FILE..................................................................................................................................... 100
10.4.6 MOTION DETECTION ....................................................................................................................... 100
10.4.7 ALARM MANAGER ........................................................................................................................... 100
10.4.8 AUDIO............................................................................................................................................ 101
10.4.9 INSTALLER ..................................................................................................................................... 101
10.4.10 SERVICE ...................................................................................................................................... 101
11. MAINTENANCE AND CLEANING.................................................................................................... 103
11.1 FUNCTION TEST................................................................................................................................. 103
11.2 CLEANING......................................................................................................................................... 103
12. DISPOSAL......................................................................................................................................... 103
13. TECHNICAL DATA............................................................................................................................ 104


60
1. Intended use
This camera is used for indoor and outdoor video surveillance (depending on the model) in
conjunction with a recording device or appropriate display unit (e.g. PC).
Use of this product for any other purpose than that described may lead to damage
to the product and other hazards. All other uses are not as intended and will result
in the invalidation of the product guarantee and warranty. No liability can be
accepted as a result. This also applies to any alterations or modifications made to
the product.
Read the user guide carefully and in full
before putting the product into operation. The user guide contains
important information on installation and operation.
2. Explanation of symbols
The triangular high voltage symbol is used to warn of the risk of
injury or health hazards (e.g. caused by electric shock).
The triangular warning symbol indicates important notes in this user manual which
must be observed.
This symbol indicates special tips and notes on the operation of the unit.
3. Scope of delivery
TVIP9X100 TVIP9X300 TVIP92500 TVIP9X600 TVIP9X700
IP camera √√√√√
Quick start guide √√√√√
General safety
instructions √√√√√
Hexagonal socket key
(without pin) √- - √-
Hexagonal socket key
(with pin) - √- - √
Reset tool √√√√√
Software CD (ABUS,
IP installer, VMS
Express)
√√√√√
Clamp for cable
attachment - √- - √
Cable gland M25 - - - - √
Cable for analogue
video output (BNC) - √- - √
Desiccant bag - - - - √
Rubber plate for
installation - - -
√(pre-
installed)
√
(separate)
You can download a PDF version of the user guide in your language at
www.abus.com via the product search.

61
4. Features and functions
TVIP91XXX
HD 720p resolution: 1280 x 720 @ 25 fps
3.6 mm fixed lens
Day/night switching with electromechanical IR blocking filter (ICR)
WDR function (46 dB) to compensate for image contrasts
IR LEDs for night vision (TVIP91100 and TVIP91600 only)
16 GB internal memory for recording in the event of a power failure (TVIP91300 and
TVIP91700 only)
Power over Ethernet (PoE)
ONVIF profile S compatible
TVIP92XXX
Full HD 1080p resolution: 1920 x 1080 @ 25 fps
Sony Xarina DSP and Sony Exmore image sensor
Tamron Motor Vario lens 3–9 mm (TVIP92100, TVIP92300, TVIP92610 and TVIP92700
only) or 9–22 mm (TVIP92600)
16 GB internal memory for recording in the event of a power failure
Day/night switching with electromechanical IR blocking filter (ICR)
IR LEDs with variable intensity (TVIP92100, TVIP92600 and TVIP92610 only)
WDR function to compensate for high image contrasts
Power over Ethernet (PoE)
ONVIF-compatible

62
5. Device description
5.1 Overview – Model numbers
Model number TVIP91100 TVIP91300 TVIP91600 TVIP91700
Resolution 720p 720p 720p 720p
DWDR/WDR DWDR,
46 dB
DWDR,
46 dB
DWDR,
46 dB
DWDR,
46 dB
2D DNR/3D DNR √√√√
Lens Fixed-lens,
3.6 mm
Fixed-lens,
3.6 mm
Fixed-lens,
3.6 mm
Fixed-lens,
3.6 mm
Operating voltage 12 V DC 12 V DC 12 V DC 12 V DC
PoE IEEE
802.3af
IEEE
802.3af
IEEE
802.3af
IEEE
802.3af
Model number TVIP92100 TVIP92300 TVIP92500 TVIP92600 TVIP92700
Resolution 1080p 1080p 1080p 1080p 1080p
DWDR/WDR WDR,
>100 dB
WDR,
>100 dB
WDR,
>100 dB
WDR,
>100 dB WDR,
>100 dB
2D DNR/3D DNR √√√√√
Lens Motor zoom,
3–9 mm
Motor zoom,
3–9 mm - Motor zoom, 9–22 mm
Motor zoom,
3–9 mm
Operating voltage 12 V DC 12 V DC 12 V DC 12 V DC 12 V DC
PoE IEEE
802.3af IEEE 802.3af
IEEE
802.3af
IEEE
802.3af IEEE 802.3af
Model number TVIP92610
Resolution 1080p
DWDR/WDR WDR,
>100 dB
2D DNR/3D DNR √
Lens Motor zoom,
3–9 mm
Operating voltage 12 V DC
PoE IEEE
802.3af
5.2 Unpacking the device
Handle the device with extreme care when unpacking it.
If the original packaging has been damaged, inspect the device first. If the device shows
signs of damage, return it in the original packaging and inform the delivery service.

63
5.3 Overview of connections, control elements, front/back
TVIP91100

64
TVIP91300

65
TVIP91600

66
TVIP91700

67
TVIP92100

68
TVIP92300

69
TVIP92500

70
TVIP926X0

71
TVIP92700

72
6. Installation
Instructions for how to mount the camera are described in the quickstart guide for the relevant IP
camera TVIP9XXXX.
When mounting the dome cameras TVIP91700 and TVIP92700 please make sure
that the desiccant bag supplied is placed inside the camera before placing on the
dome. The bag must be placed close to the base plate. The bag must not be in the
field of view of the lens. The bag must not be placed directly behind the lens or the
camera board.
6.2 Laying the cables
You must pay attention to the following instructions when laying the cables:
TVIP91100/TVIP92100
A break-out panel for feeding the cable is located on the base plate for laying the cables at the
side. Use pliers to remove the break-out panel. Use a file to smooth out the edges of the break-
out panel.
TVIP91300/TVIP92300
A break-out panel for feeding the cable is provided for laying the cables at the side. Use a flat,
narrow screwdriver to remove the break-out panel from the plastic.
These cameras are equipped ex works with a short connecting cable for networking
(RJ45), power supply (barrel connector) and analogue video output. Making the
connection is possible from inside the camera. In the most simple case, a network
cable with Power over Ethernet power supply is all that's needed to operate the
camera.
If the functions switching input, switching output or audio input/output (TVIP92300
only) are needed, you must install an extended connecting cable (for TVIP91300:
TVAC40700; for TVIP92300: TVAC40720).
TVIP92500
When laying the cable, ensure that none of the plug connections is subject to mechanical tension.
Furthermore, cables must be fixed in such a way as to prevent the plug from being bent or
snapped off.
TVIP91600/TVIP92600 / TVIP92610
A break-out panel for feeding the cable is located on the base plate for laying the cables at the
side. Use pliers to remove the break-out panel. Use a file to smooth out the edges of the break-
out panel.

73
TVIP91700/TVIP92700
For this type of camera, the cable is intended to be laid at the side or concealed. There are
openings at the side and on the base for this. The unused opening is sealed using a blind plug.
For installation the supplied cable gland must be used (for the side and base) in accordance with
protection class IP66. When using the optional wall bracket (TVAC31310), the cable gland may
be omitted, as the wall bracket panel and dome camera have been manufactured to fit together
tightly.
These cameras are equipped ex works with a short connecting cable for networking
(RJ45), power supply (barrel connector) and analogue video output. Making the
connection is possible from inside the camera. In the most simple case, a network
cable with Power over Ethernet power supply is all that's needed to operate the
camera.
If the functions switching input, switching output or audio input/output (TVIP92300
only) are needed, you must install an extended connecting cable (for TVIP91300:
TVAC40700; for TVIP92300: TVAC40720).
6.3 Power supply
Before starting installation, ensure that the power supply voltage and the rated voltage of the
camera are identical.
TVIP9XXXX
DC power supply, 12 V
The cameras have a 12 V DC power supply. Ensure correct polarity when connecting. The
polarity is indicated with "+" and "-".
In addition, all cameras have Power over Ethernet (PoE) to supply the camera directly via the
network cable.
If the camera has the function "Record during network failure" and this function
is to be used, it's necessary to supply the camera via the 12 V DC terminal (do
not use PoE).
When using PoE, you must pay attention to the power budget of the network
switch. Make sure that each network port provides the maximum power for the
standard (15.4 watt per network port).
If the network switch distributes the power dynamically via all ports, it may
cause power shortages.

74
6.4 Attaching the network cable
The maximum network cable (CAT7) length from the camera to the nearest active network point
(e.g. network switch) should not exceed 100 metres.
6.5 Aligning the camera
Instructions for how to align the camera are given in the quickstart guide for the relevant IP
camera TVIP9XXXX.
6.6 Zoom and focus settings
TVIP91100/TVIP91300/TVIP91600/TVIP91700
The cameras have a built-in fix lens. The focal length is dependent on the lens and the focus is
already factory-set. It is not possible to change the angle of view or the focus.
TVIP92100/TVIP92300/TVIP92600/TVIP92610/TVIP92700
The cameras have a built-in Motor Vario zoom lens. It is possible to change the zoom factor or
adapt the focus via the camera's web interface ("master" or "installer" access).
The zoom factor can be changed in stages, whereas the focus is automatically set for each of
these zoom factors. It's possible to change the focus of each zoom factor via the camera's web
interface ("master"/"installer" access). The change will be saved to the camera. When the camera
undergoes a factory reset, the factory-set zoom/focus relationship is reset too.
It is also possible to operate the zoom function using the two reset buttons. You can find a more
detailed description of this under point 6.10 "Restoring factory settings (reset)".
TVIP92500
Settings for zoom and focus are made manually in the lens to be installed (lens is not included in
the scope of delivery).