Acer AB460 F1 User manual

AB7000 Series
User Guide

Model Number :
Serial Number:
Purchase Date:
Place of Purchase:
Copyright © 2010. All Rights Reserved.
Acer AB 7000 Series
User Guide
Acer AB 7000

iii
Information for your safety and
comfort
Safety instructions
Read these instructions carefully. Keep this document for future
reference. Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
CAUTION for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting
power to the power supply unit:
• Install the power supply unit before connecting the power cord to
the AC power outlet.
• Unplug the power cord before removing the power supply unit
from the computer.
• If the system has multiple sources of power, disconnect power
from the system by unplugging all power cords from the power
supplies.
CAUTION for accessibility
Be sure that the power outlet you plug the power cord into is easily
accessible and located as close to the equipment operator as possible.
When you need to disconnect power to the equipment, be sure to
unplug the power cord from the electrical outlet.
Warnings
• Do not use this product near water.
• Do not place this product on an unstable cart, stand or table. If the
product falls, it could be seriously damaged.

iv
• Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating.
These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug
or other similar surface. This product should never be placed near
or over a radiator or heat register, or in a built-in installation
unless proper ventilation is provided.
• Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock. Never spill liquid
of any kind onto or into the product.
• To avoid damage of internal components and to prevent battery
leakage, do not place the product on a vibrating surface.
• Never use it under sporting, exercising, or any vibrating
environment which will probably cause unexpected short current
or damage rotor devices, HDD, Optical drive, and even exposure
risk from lithium battery pack.
• This product is not suitable for use with visual display workplace
devices according to B2 of the German Ordinance for Work with
Visual Display Units.
Using electrical power
• This product should be operated from the type of power indicated
on the marking label. If you are not sure of the type of power
available, consult your dealer or local power company.
• Do not allow anything to rest on the power cord. Do not locate
this product where people will walk on the cord.
• If an extension cord is used with this product, make sure that the
total ampere rating of the equipment plugged into the extension
cord does not exceed the extension cord ampere rating. Also,
make sure that the total rating of all products plugged into the
wall outlet does not exceed the fuse rating.
• Do not overload a power outlet, strip or receptacle by plugging in
too many devices. The overall system load must not exceed 80% of
the branch circuit rating. If power strips are used, the load should
not exceed 80% of the power strip's input rating.
• This product's power supply is equipped with a three-wire
grounded plug. The plug only fits in a grounded power outlet.
Make sure the power outlet is properly grounded before inserting
the power supply plug. Do not insert the plug into a non-

v
grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
• Use the product only with the supplied power supply cord set. If
you need to replace the power cord set, make sure that the new
power cord meets the following requirements: detachable type,
UL listed/CSA certified, VDE approved or its equivalent, 4.6 meters
(15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage points or other
risks. Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to
qualified service personnel when:
• the power cord or plug is damaged, cut or frayed
• liquid was spilled into the product
• the product was exposed to rain or water
• the product has been dropped or the case has been damaged
• the product exhibits a distinct change in performance, indicating a
need for service
• the product does not operate normally after following the
operating instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.

vi
Additional safety information
Your device and its enhancements may contain small parts. Keep them
out of the reach of small children.
Disposal instructions
Do not throw this electronic device into the trash when
discarding. To minimize pollution and ensure utmost
protection of the global environment, please recycle. For
more information on the Waste from Electrical and
Electronics Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm.
Mercury advisory
For projectors or electronic products containing an LCD/CRT
monitor or display: Lamp(s) inside this product contain
mercury and must be recycled or disposed of according to local, state
or federal laws. For more information, contact the Electronic Industries
Alliance at www.eiae.org. For lamp-specific disposal information,
check www.lamprecycle.org.
Tips and information for comfortable use
Computer users may complain of eyestrin and headaches after
prolonged use. Users are also at risk of physical injury after long hours
of working in front of a computer. Long work periods, bad posture,
poor work habits, stress, inadequate working conditions, personal
health and other factors greatly increase the risk of physical injury.
Incorrect computer usage may lead to carpal tunnel syndrome,
tendonitis, tenosynovitis or other musculoskeletal disorders. The
following symptoms may appear in the hands, wrists, arms, shoulders,
neck or back:
• numbness, or a burning or tingling sensation
• aching, soreness or tenderness
• pain, swelling or throbbing
• stiffness or tightness
• coldness or weakness

vii
If you have these symptoms, or any other recurring or persistent
discomfort and/or pain related to computer use, consult a physician
immediately and inform your company's health and safety
department.
The following section provides tips for more comfortable computer
use.
Finding your comfort zone
Find your comfort zone by adjusting the viewing angle of the monitor,
using a footrest, or raising your sitting height to achieve maximum
comfort. Observe the following tips:
• refrain from staying too long in one fixed posture
• avoid slouching forward and/or leaning backward
• stand up and walk around regularly to remove the strain on your
leg muscles
• take short rests to relax your neck and shoulders
• avoid tensing your muscles or shrugging your shoulders
• install the external display, keyboard and mouse properly and
within comfortable reach
• if you view your monitor more than your documents, place the
display at the center of your desk to minimize neck strain
Taking care of your vision
Long viewing hours, wearing incorrect glasses or contact lenses, glare,
excessive room lighting, poorly focused screens, very small typefaces
and low-contrast displays could stress your eyes. The following sections
provide suggestions on how to reduce eyestrain.
Eyes
• Rest your eyes frequently.
• Give your eyes regular breaks by looking away from the monitor
and focusing on a distant point.
• Blink frequently to keep your eyes from drying out.
Display
• Keep your display clean.

viii
• Keep your head at a higher level than the top edge of the display
so your eyes point downward when looking at the middle of the
display.
• Adjust the display brightness and/or contrast to a comfortable
level for enhanced text readability and graphics clarity.
• Eliminate glare and reflections by:
• placing your display in such a way that the side faces the window
or any light source
• minimizing room light by using drapes, shades or blinds
• using a task light
• changing the display's viewing angle
• using a glare-reduction filter
• using a display visor, such as a piece of cardboard extended from
the display's top front edge
• Avoid adjusting your display to an awkward viewing angle.
• Avoid looking at bright light sources, such as open windows, for
extended periods of time.
Developing good work habits
Develop the following work habits to make your computer use more
relaxing and productive:
• Take short breaks regularly and often.
• Perform some stretching exercises.
• Breathe fresh air as often as possible.
• Exercise regularly and maintain a healthy body.
Warning! We do not recommend using the computer on a couch
or bed. If this is unavoidable, work for only short periods, take
breaks regularly, and do some stretching exercises.

ix
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses,
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the
device off and on, the
user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician
for help.
Notice: Shielded cables
All connections to other computing devices must be made using
shielded cables to maintain compliance with FCC regulations. In
compliance with FCC regulations, use shielded cables to connect to
other computing devices. A dual-link cable is recommended for DVI
output.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.)
certified to comply with the Class A limits may be attached to this
equipment. Operation with non-certified peripherals is likely to result
in interference to radio and TV reception.

x
Caution
Changes or modifications not expressly approved by the manufacturer
could void the user's authority, which is granted by the Federal
Communications Commission, to operate this computer.

xi
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Notice: Canadian users
This Class A digital apparatus complies with Canadian ICES-003.
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-
003 du Canada.
Compliant with Russian regulatory certification
Notice for Australia
For safety reasons, only connect headsets with a telecommunications
compliance label. This includes customer equipment previously labelled
permitted or certified.
Notice for New Zealand
1 The grant of a Telepermit for any item of terminal equipment
indicates only that Telecom has accepted that the item complies
with minimum conditions for connection to its network. It
indicates no endorsement of the product by Telecom, nor does it
provide any sort of warranty. Above all, it provides no assurance
that any item will work correctly in all respects with another item
of Telepermitted equipment of a different make or model, nor
does it imply that any product is compatible with all of Telecom's
network services.
2 This equipment is not capable, under all operating conditions, of
correct operation at the higher speeds for which it is designed.
Telecom will accept no responsibility should difficulties arise in
such circumstances.
3 Some parameters required for compliance with Telecom's
Telepermit requirements are dependent on the equipment (PC)
associated with this device. The associated equipment shall be set

xii
to operate within the following limits for compliance with
Telecom's Specifications:
a There shall be no more than 10 call attempts to the same number
within any 30 minute period for any single manual call initiation, and
b The equipment shall go on-hook for a period of not less than 30
seconds between the end of one attempt and the beginning of the
next call attempt.
4 Some parameters required for compliance with Telecom's
Telepermit requirements are dependent on the equipment (PC)
associated with this device. In order to operate within the limits
for compliance with Telecom's specifications, the associated
equipment shall be set to ensure that automatic calls to different
numbers are spaced such that there is not less than 5 seconds
between the end of one call attempt and the beginning of
another.
5 This equipment shall not be set up to make automatic calls to
Telecom's 111 Emergency Service.
6 This device is equipped with pulse dialing while the Telecom
standard is DTMF tone dialing. There is no guarantee that Telecom
lines will always continue to support pulse dialing.
7 Use of pulse dialing, when this equipment is connected to the
same line as other equipment, may give rise to bell tinkle or noise
and may also cause a false answer condition. Should such problems
occur, the user should NOT contact the telecom Fault Service.
8 This equipment may not provide for the effective hand-over of a
call to another device connected to the same line.
9 Under power failure conditions this appliance may not operate.
Please ensure that a separate telephone, not dependent on local
power, is available for emergency use.
Laser compliance statement
The CD or DVD drive used with this computer is a laser product.
The CD or DVD drive's classification label (shown below) is located on
the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID
EXPOSURE
TO BEAM.

xiii
Appareil à laser de classe 1
Attention : Radiation laser visible et invisible en cas d’ouverture. Éviter
toute exposition aux rayons.
Laserprodukt der Klasse 1
Achtung: Beim Öffnen werden unsichtbare Laserstrahlen freigelegt.
Setzen Sie sich diesen Strahlen nicht aus.
Prodotto laser di classe 1
Attenzione: Radiazioni laser invisibili in caso d’apertura. Evitare
l’esposizione ai raggi.
Producto láser de Clase 1
Precaución: Cuando está abierta, hay radiación láser. Evite una
exposición al haz de luz.
Produto Laser de Classe 1
Precaução: Radiação laser invisível quando aberto. Evite exposição ao
feixe.
Laserproduct klasse 1
Voorzichtig: Onzichtbare laserstraling indien geopend. Voorkom
blootstelling aan straal.
Declaration of Conformity for EU countries
Hereby, Acer, declares that this system is in compliance with the
essential requirements and other relevant provisions of Directive 1999/
5/EC.
List of applicable countries
This device must be used in strict accordance with the regulations and
constraints in the country of use. For further information, please
contact local office in the country of use. Please see http://
ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.

xiv

Contents
Information for your safety and comfort iii
Regulations and safety notices ix
1 Document Description 1
About this Manual 2
Manual Organization 2
2 Chassis Enclosure 5
Introduction 6
External and internal structure 7
Front panel 7
Rear Panel 8
Product Configuration Guidance 9
Setup and Installation 11
Overview 11
Unpacking the System 11
Choosing a Setup Location 11
Rack Precautions 12
Server Precautions 12
Rack Mounting Considerations 13
Installing the System Into a Rack 14
Rack Mounting Hardware 14
Installation 14
Chassis Management Module 18
Module Installation 20
Configuring the CMM 21
CMM Functions 24
Firmware 27
Acer Smart Blade Console 28
Introduction 28
Network Connection/Login 28
Home Page 29
Blade System 32
Virtual Media 40
System Health 45
User Management 47
KVM Settings 52
Device Settings 57
Maintenance 67
Remote Console 71
Power Supply Modules 80
Power Supply Failure 81

xvi
Installing a Power Supply 81
Removing a Power Supply 82
Power Supply Fans 83
Power Components 84
Power Cord 84
Power Cord Tie and Clamp 85
Double-Wide Modules 87
Setting up a Double-Wide Bay 87
3 Server Blades: Setup and Installation 91
Overview 92
Installing Blade Modules 92
Powering Up a Blade Unit 92
Powering Down a Blade Unit 92
Removing a Blade Unit from the Enclosure 92
Removing/Replacing the Blade Cover 93
Installing a Blade Unit into the Enclosure 93
Processor Installation 95
DIMM Installation 97
Hard Disk Drive Installation 98
Infiniband mezzanine card installation 100
Installing the Operating System 102
Installing with an External USB CD-ROM Drive 102
Installing via PXE Boot 102
Installing via Virtual Media 103
Acer Smart Console 104
Configuring BMC the IPMI Settings 104
AB460 F1 147
External and Internal Structure 147
KVM Connector 149
Front Panel LED Indicators 149
Blade Unit Components 150
Mainboard 152
CMOS Clear 153
Memory Support 154
Memory Installation 154
Populating Memory Slots 154
Hard Disk Drives 163
AB460 F1 System BIOS 165
Introduction 165
Starting the Setup Utility 165
BIOS Updates 166
Flashing BIOS 166

xvii
Running Setup 167
Main BIOS Setup 168
Advanced Settings 170
Security 186
Server Management Settings 188
Boot 193
Exit Options 199
AB460 F1 Onboard SAS RAID Configuration 201
AB2x280 F1 203
Internal and External Structure 203
Control Panel 203
Blade Unit Components 206
Mainboard 208
Memory Support 210
Memory Installation 210
Populating Memory Slots 210
Supported Memory Population 212
AB2x280 F1 Hard Disk Drives 218
AB2x280 F1 System BIOS 219
Introduction 219
Starting the Setup Utility 219
BIOS Updates 220
Flashing BIOS 220
Running Setup 221
Main BIOS Setup 222
Advanced Settings 224
Boot 248
Exit Options 254
AB2x280 F1 Onboard SATA RAID Configuration 256
Enabling Adaptec onboard SATA RAID 257
4 Networking Switch Modules 261
Acer 1/10Gb Ethernet Switch Module 262
Installing/Removing a Switch Module 263
Installing a Switch Module 263
Removing a Switch Module 264
Configuring the Switch Module 265
Command Line 269
Internal and External Structure 271
Ports 273
Web-based Management Utility 274
Overview 274
Nomenclature 275

xviii
Login 276
Home Page 277
Top Page Links 278
Top LED Display 279
Left Side Tree 279
Middle Configuration Link Table 279
System Management Page 280
System Settings 281
File Management 284
Firmware Upgrade 286
Management Security 286
Syslog 296
ACL 299
WEBGUI Settings 304
SNMP 305
RMON 317
QoS 323
NTP Settings 328
Stack 330
Layer 2 Management 339
Layer 2 Basic Settings 339
Port Manager 340
VLAN 348
Dynamic Vlan 357
RSTP 360
MSTP 366
LA 374
802.1x 378
Filters 384
Layer 3 Management 387
IP 387
IP V6 392
DHCP Server 399
DHCP Relay 401
RIP 403
RIPng 409
OSPF 411
OSPF V3 421
BGP 428
RRD 439
RRD6 443
VRRP 447
Multicast 450
GMP Snooping 451

xix
Dynamic Multicast 457
IGMP 459
PIM 463
DVMRP 469
Statistics 472
Interface 472
Radius 476
TACACS+ Statistics 478
RMON Ethernet Statistics 480
SNMP Statistics 483
VLAN 487
RSTP Statistics 493
MSTP Statistics 496
Link Aggregation (LA) 500
802.1X 502
IP 507
IPv6 510
RIP Statistics 515
RIP6 516
OSPF 519
OSPFv3 521
VRRP Statistics 523
IGMP Snooping 525
IGMP Statistics 529
PIM 531
DVMRP 537
Firmware Upgrading Procedures 540
Firmware Failure Recovery Steps 544
InfiniBand Modules 547
Overview 547
Installation and Configuration of
InfiniBand Switch Modules 547
Acer 4X QDR InfiniBand Switch Module 548
Acer 4X QDR InfiniBand Switch Module
with Integrated CMM 550
5 Acer Smart Blade Manager 553
Acer Smart Blade Manager 554
Introduction 554
Blade System tab 555
Text Console 571
KVM console 572
Event Log 574

xx
Logon Management 575
Virtual Media 577
CMM Setting 578
Connecting to the Slave CMM 579
Appendix A: Troubleshooting 581
BIOS POST Messages 582
BIOS POST Codes 587
Recoverable POST Errors 587
Terminal POST Errors 587
Index 597