Adam Equipment CPW 25 User manual

Adam Equipment
CPW COMPACT SCALE
© ADAM EQUIPMENT CO. LTD.
pn. 3935 Rev. D, November 2002

© Adam Equipment Company 2002
2
INTRODUCTION
The CPW Compact Scales are available in 4 models, with capacities from 25kg to 150kg.
The scales are general purpose compact scales suitable for all general weighing purposes.
All scales come complete with an easy to clean stainless steel top on a study steel frame,
and a remote indicator with a large LCD display which is easy to read from a distance.
The water-resistant keyboard has 4 easy to use function keys: GROSS/NET-UNIT-
ON/OFF-TARE.
With the standard AC adapter included and the facility for drycell batteries, the CPW
compact scales can be used in a fixed location or as a portable scale.
.
ASSEMBLY
The scale comes complete with the stainless steel top and a power supply module.
Plug the power supply into the socket on the side of the base. Then plug the power supply
into the mains power.
If the wall-mount bracket is used, mount the bracket to the wall using the enclosed screws.
Then attach the display to the bracket using the 2 thumb screws put into the ends of the
housing. Tighten the screws to secure the display.
The scale can also be used with batteries for a truly portable scale.
Installing batteries
Power can be supplied by mains adapters delivering 9VDC 100 mA , or using batteries
inside of scale’s head (6 x AA Size). Remove the cover from the battery compartment
under the stainless steel pan by lifting the tab. Install six AA size batteries as shown:
It is suggested Alkaline batteries be used for best life.
6 X "AA" Alkaline

© Adam Equipment Company 2002
3
SPECIFICATIONS
CPW Compact Scale
Model # CPW 25 CPW 50 CPW 100 CPW 150
Maximum
Capacity 25 kg 50 kg 100 kg 150 kg
Readability 0.01 kg 0.02 kg 0.05 kg 0.10 kg
Alternate
Weighing Units 55lb x 0.02lb 885 oz. x 0.5oz. 110lb x 0.05lb 1170oz. x 1oz. 221lb x 0.1lb 3544oz. x 2oz. 332lb x 0.2lb 5325oz. x 5oz.
Resolution 1:2500 1:2500 1:2000 1:1500
Tare Range Full range Full range Full range Full range
Units of Measure Kg / lb / oz
Stabilisation Time 1-2 secs.
Operating
Temperature 5°C - 40°C 13 F - 104°F
Power supply 6 x AA batteries or 9V 100ma AC adapter
Calibration Automatic External
Calibration mass 20 kg / 50 lb 40 kg / 100 lb 100 kg / 200 lb 100 kg / 200 lb
Indicator display 26mm/1.0” LCD digital display showing net, gross, zero, stable and
weighing units
Scale Housing Stainless steel base and top
Pan Size 310 x 300 mm / 12¼ x 12”
Dimensions (w x d
x h)
Base: 310 x 300 x 50 mm
12 ¼ x 12 x 2”
Indicator: 270 x 80 x 30mm
11 x 3 x 1”
Gross Weight 4.8 Kg / 10.6 lb.

© Adam Equipment Company 2002
4
OPERATOR’S INSTRUCTIONS
Key description
Tare - Set the display to zero by storing the current weight in
the tare memory
On / Off - Turns the scale on or off,
Units - Select kilograms, pounds or ounces
Gross/Net - Select either Gross weight or Net weight when
a tare weight has been entered
To weigh on the scale turn the scale on using the On/Off key. After the display is at zero,
place an item to be weighed on the platform. The display will show the weight. The unit
will be shown in kilograms unless the user has selected either pounds or ounces
previously.
If an empty container is used the weight can be ignored by zeroing the display. To zero
the display, press the TARE key. Then when material is placed in the container only the
weight of the material will be shown.
Switch between showing the Net Weight (Material Only) and the Gross Weight (container
plus material) by pressing the Gross/Net key.
D I S P L A Y S Y M B O L S
Symbol Description
 scale in auto zero range (indication = accurate zero)

result is stable
kg , lb or oz scale in weighing mode
Lo-bAt battery is weak, after 5 minutes the scale will turn off
Show the Net Weight is being display (NW) or the Gross Weight is
displayed (GW)

© Adam Equipment Company 2002
5
CALIBRATION
Occasionally the scale should be verified that it is weighing correctly by measuring a
known mass of approximately the scale capacity. Tare the scale, place the mass on the
centre of the platform and note the reading. Calibrate the scale if necessary.
Before beginning make sure you have the mass specified and you know the mass is
accurate. The scale can calibrate using either kilograms or pounds. See the below for
the mass required. The following procedure assumes the parameter for local gravity
correction “Grav” has been set to OFF. If it has been set to ON then reset the value to off
as shown in the next section.
PROCEDURE
Turn the scale off.
Press and hold the On/Off key then press the Units key 3 times. Release the On/Off key.
The display will show a value from the internal counters. The typical value is 2000 to 8000.
Press the Tare key. Display will show zero.
Press the Unit key to select either kilograms (kg) or pounds (lb).
Place the calibration weight on the scale, centred on the platform.
CPW 25 20kg OR 50 lb
CPW 50 40kg OR 100 lb
CPW 100 100kg OR 200 lb
CPW 150 100kg OR 200 lb
The display will show a value from the internal counters again.
Press the Tare key again.
The display will show " CAL" then return to weighing showing the value of the weight
used.
Remove the weight. Verify the scale is calibrated correctly.
SET FUNCTIONS
The scale can be set as desired for the user. The settings that can be changed are:
Weighing Units enabled
Time delay before the scale automatically turns off.
Enable or disable the correction for the local gravity.
Press and hold the TARE key for 3 seconds until the display shows “Set” then the first
menu option “Unit”

© Adam Equipment Company 2002
6
Press the Unit key to cycle through the options.
At each function press the Gross/Net key to enter the function and then press the Unit
key to view the options, pressing the Gross/Net key again to return to the functions menu
with the current option set.
Each weighing unit can be enabled or disabled.
The Automatic Turn-off time can be set to a time or disabled (off)
The “Grav” parameter controls if the scale will use the local value for gravity during
calibration. Normally se t this parameter to OFF.
Advance to and then press the Gross/Net key to exit the menu.
End
Unit
A.Off
Grav
End
SEt
kg Lb Oz.
Unit
On Off On Off On Off
120 180 240.
300 Off
A.Off
Seconds delay until turn off
Off On
Grav

© Adam Equipment Company 2002
7
Manufacturer’s Declaration of Conformity
This product has been manufactured in accordance with the harmonised European standards,
following the provisions of the below stated directives:
Electro Magnetic Compatibility Directive 89/336/EEC
Low Voltage Directive 73/23/EEC
Adam Equipment Co. Ltd.
Bond Avenue
Denbigh East Estate
Milton Keynes, MK1 1SW
United Kingdom
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. The
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Shielded interconnect cables must be employed with this equipment to insure compliance with the
pertinent RF emission limits governing this device.
Changes or modifications not expressly approved by Adam Equipment could void the user's authority
to operate the equipment.

© Adam Equipment Company 2002
8
ADAM EQUIPMENT is a global supplier with more than 30 years experience in the production and sale of
electronic weighing equipment.
Products are supplied and serviced from our company locations in the UK, USA and SOUTH AFRICA and
distributed through a world wide dealer network.
ADAM EQUIPMENT's products are predominantly designed for the laboratory, educational, medical and
industrial markets.
The product range can be summarised as follows:
−Analytical and Precision laboratory balances
−Basic range of top loading balances for schools and educational establishments
−Counting scales for general industrial and warehouse applications
−Digital weighing/check-weighing scales
−High performance platform scales with extensive software facilities including parts counting, percent
weighing etc.
−Digital electronic scales for medical use
−Retail price computing scales
ADAM EQUIPMENT and their distributors offer a full range of technical services such as on site and
workshop repair, preventative maintenance and calibration facilities.
ADAM EQUIPMENT operates an approved quality management system and is certified to ISO9002.
Visit our Website at
www.adamequipment.com
Adam Equipment Co. Ltd.
Bond Avenue
Milton Keynes
MK1 1SW
UK
Phone: [phone]
Fax: [phone]
e-mail: [email protected]
Adam Equipment Inc.
26 Commerce Drive
Danbury, CT
06810
USA
Phone: [phone]
Fax: [phone]
e-mail: [email protected]
Adam Equipment S.A. (Pty) Ltd.
P.O. Box 1422
Kempton Park 1620
Johannesburg
Republic of South Africa
Phone [phone]
Fax: [phone]
e-mail: [email protected]
©Copyright by Adam Equipment Co. Ltd. All rights reserved. No part of this publication may be reprinted or
translated in any form or by any means without the prior permission of Adam Equipment.
Adam Equipment reserves the right to make changes to the technology, features, specifications and design of the
equipment without notice.
All information contained within this publication was to the best of our knowledge timely, complete and accurate
when issued. However, we are not responsible for misimpressions which may result form the reading of this
material.
The latest version of this publication can be found on our Website.