ADC Adtemp 658 User manual

AdtempTM 658
Electronic Stethoscope
INSTRUCTIONS
FOR USE

2
ADC® Adscope® 658 Electronic Stethoscope
Thank you for choosing the ADC® Adscope® 658 Electronic Stethoscope. We're proud
of the care and quality that goes into the manufacture of each and every item that bears
our name. Only the finest materials are used to assure you of a timeless instrument
designed for optimum performance.
You'll quickly appreciate the results, for you now own one of the finest electronic
stethoscopes that money can buy. With proper care and maintenance, your Adscope 658
is sure to provide you with many years of dependable service. Please read the following
instructions and general information which will prove helpful in allowing you to enjoy
your ADC product.
Device Description and Intended Use
The Adscope 658 Electronic Stethoscope is intended for medical diagnostic purposes only.
It can be used for the amplification of heart, lung, and other body sounds. Frequency
selection and volume buttons enable operator control. The 658 can be used on patients
of any age undergoing a physical assessment. This device is designed for use in a
professional setting by a healthcare practitioner.
Symbol Definitions
Symbol Definition
Important warning/caution
Not made with natural rubber latex
Equipment type is BF
LATEX
Symbol Definition
Low power indication
Manufacturer’s information
Serial number

3
• Do not tap hard or scratch diaphragm of the chestpiece while wearing the eartips with
the stethoscope powered on.
• Do not bend or apply excessive force to the stethoscope.
• Do not disassemble, repair, or modify the device. When repair is needed, contact the
ADC Customer Service Dept. (see reverse side).
• Avoid any place of high humidity or wet conditions such as a bathroom. Pressing the
power button while the stethoscope is wet could cause irreparable damage to the device.
• Do not immerse in water. This product is not water resistant, avoid excessive moisture.
• Sounds might be distorted if the battery level is low.
• This product is intended for use by a medically trained specialist.
• Fully charge battery before first use.
• This scope cannot be used while being charged.
• Incorrect replacement of lithium batteries will result in an unacceptable risk.
• Replacement of lithium batteries by untrained personnel can result in a hazard.
• Do not dispose of in municipal waste. Waste batteries may be returned to ADC’s
service center at: 55 Commerce Drive, Hauppauge NY 11788 or you may contact your
local EPA office for guidance on the proper disposal of lithium ion batteries.
Caution:
• Avoid direct exposure to sunlight, heating fans, or heating appliances.
• Avoid strong magnetic fields beside the device. These could cause it to malfunction.
• Do not use the stethoscope for purposes other than the intended use.
• Federal law restricts this device to sale by or on the order of a physician or licensed
healthcare practitioner.
• Always check security of the eartips before use.
Adscope 658 Electronic Stethoscope Features:
• Improves low-frequency sound transmission characteristic with the use of a
piezopolymer film contact microphone
• MPU controlled automatic power off
• Mode selection function (bell, diaphragm)
• 8-level digital volume control
• Holds last mode and volume setting
General Warnings
A warning statement in this manual identifies a condition or practice which, if not
corrected or discontinued immediately, could lead to patient injury, illness, or death.

4
An acoustic microphone used in most electronic stethoscopes may have frequency
characteristics not suitable for the body sounds, especially for the low-frequency heart
sounds. Other stethoscopes provide the internal body sounds not directly from the body
surface, but through the air layer between the body surface and the microphone. The 658
solves these problems with the use of a piezopolymer film contact microphone which is
the heart of the 658. The 658 has wide-frequency characteristics and enables you to detect
the heart and lung sounds more precisely.
Name and Function of Each Part
Operation of the Headset
The Adscope 658 electronic stethoscope is designed to
provide comfortable ear fittings and the best sound
transmission. The binaurals (ear tubes) are angled at
15° to permit a comfortable, acoustically sealed aural fit.
Eartips should point forward, towards the bridge of the nose, to fit properly.
Display
Battery
Volume
Mode
(Bell/Diaphragm)
USB
Port
Multifunction Button
Tubing
Volume up
Volume down
Diaphragm mode
Bell mode
P
e
r
f
o
r
m
a
n
c
e
•
V
a
l
u
e
•
Q
u
a
l
i
t
y
•
S
e
r
v
i
c
e
P
e
r
f
o
r
m
a
n
c
e
•
V
a
l
u
e
•
Q
u
a
l
i
t
y
•
S
e
r
v
i
c
e
®
American Diagnostic Corporation
Chestpiece
• Contact microphone
• Protective cover
Diaphragm
• Silicone diaphragm
Battery Compartment
• Li-ion battery
• Reset button
Power
Button
CORRECT INCORRECT

5
Adjusting the Spring Tension in the Headset
To reduce the tension, grip the binaurals firmly using both
hands with fingers at the center of the “Y” in the tubing,
thumbs at each side where the tubing branches out. Flex
binaurals gradually until the desired tension is obtained.
To increase the tension, grip the binaurals in the hand and squeeze the binaural tubes
together gradually. Excessive adjustment of the spring tension could weaken the spring.
Power ON/OFF
Press the power button to turn the 658 on. The multifunction button will turn blue, and
the LCD will show the selected mode and volume. The backlight will stay on for fifteen
seconds. The unit will remain on for up to three minutes, but the display will
remain dark to conserve power - A quick press of any button will
awaken the unit. Press the Power button for
two seconds (or more) then release to manu-
ally power down the unit. The 658 turns off
automatically three minutes after the last
button is pressed.
Volume Control
While auscultating, press the volume button ‘
’
to increase the sound level, and press the volume
button ‘ V’ to decrease the sound level. The volume
is divided into eight levels.
Mode Selection
After the 658 powers on, pressing either the Bell or Diaphragm mode button will change
the mode.
B - Bell (Low Frequency 15-200Hz)
D - Diaphragm (High Frequency 100-500Hz)
Bell mode provides excellent detection of low &
medium-pitched heart sounds and murmurs.
Diaphragm mode is designed for the detection
of pulmonary sounds and high-pitched murmurs,
clicks, and ejection sounds.
Power Button
Volume
Buttons
Diaphragm
Mode Button
Bell Mode
Button
V

Battery Charging
When you see the low battery icon on the LCD display, you’ll need to charge the unit. To
charge, make sure the unit is off, then open the USB cover and use the enclosed cable to
connect the scope to a power source. A full charge takes about 70 minutes.
When the unit is off and the battery is charging, the backlight display will be red. A blue
backlight while charging simply means the unit is on, and does not reflect when charging
is complete. To confirm that the unit is fully charged, remove the USB cable, power on,
and check the battery icon.
Cell Model No: PR-632540N
Product Name:
Secondary ( Rechargeable ) 3.7V Li-ion
Battery 620mAh, 2.294Wh
TCL Hyperpower Batteries Inc
No.,3,Hechangdongliu Rd.
Huitai Industrial Zone,
Huicheng District, Huizhou,
Guangdong,P.R.China,516006
Replacing the Eartips
To replace AdsoftTM Plus Eartips: Slide the eartip over adapter
until it locks tight into internal channel. Repeat steps for second aural
tube. Eartips may be removed from binaurals for a thorough cleaning.
Periodically check that eartips are tightly secured to binaurals.
Caution: Always check security of eartip before inserting in ears.
Replacing the Diaphragm
Your 658 chestpiece is equipped with an ultrasensitive piezoelectric
sound transducer, covered by a silicone diaphragm.
To remove the silicone diaphragm: Gently pull off one side of
the diaphragm from the rim, and continue around
edge until the diaphram comes completely off (Figure 1).
To replace the silicone diaphragm:
Clip one edge of the new diaphragm on the chestpiece rim and
gently stretch until entire diaphragm inserts fully in the track
around the rim (Figure 2).
6
NOTE:
• Fully charge before first use.
• The 658 scope cannot be used while it is being charged.
USB
Port
Figure 1
Figure 2

7
NOTE: Do not touch piezoelectric sound transducer located in
the center of the chestpiece under the diaphragm, as it is
extremely sensitive and susceptible to damage (Figure 3).
Care and Maintenance
• Avoid extreme heat, cold, solvents, or oils.
• Do NOT leave exposed to direct sunlight for prolonged periods of time.
• The headset can be wiped down with alcohol or mild soapy water.
• Eartips may be removed from binaurals for a thorough cleaning.
• Periodically check that eartips are tightly secured to binaurals.
• Do NOT immerse stethoscope in any liquid or subject to steam sterilization.
• Chestpieces and diaphragms can be wiped down with 70% isopropyl alcohol for
cleaning purposes.
It is unnecessary to disassemble the unit for cleaning. Use a slightly moistened cotton cloth
with alcohol to clean chestpiece diaphragm, binaurals, and eartips. Be careful to prevent
alcohol seepage under the diaphragm, as it may cause significant damage to the microphone
and electronic circuits.
Caution: Never immerse instrument in any liquid. Do not apply excessive force to the
diaphragm. Your 658 has a replaceable diaphragm with a piezopolymer film contact
microphone positioned behind it. The chestpiece is not user-serviceable and should never
be disassembled, except to replace the diaphragm.
To order any replacement parts, contact our Customer Service department at 1-800-232-2670.
Troubleshooting Solutions
Figure 3
Troubleshooting Possible Problems
PROBLEM SOLUTION
Battery will not charge
Poor sound quality, intermittent
sound amplification, or
no sound amplification
Damaged/worn chestpiece
diaphragm
Low battery icon is displaying
Check battery connection. If battery is properly connected and will
not charge, battery must be replaced. Contact your local ADC dealer.
Contact your local ADC dealer for warranty service on your stethoscope.
Contact your local ADC dealer for warranty service on your stethoscope.
Charge battery. If icon displays frequently despite regular charges
contact your local ADC dealer for replacement battery.

Operating Environment
• Temperature: -4°F to 104°F (-20°C ~ 40°C)
• Humidity: 20 to 95% Relative humidity
• Atmospheric Pressure: 101.325 kPa (760mmHg)
Storage Environment
• Temperature: -4°F to 122°F (-20°C ~ 50°C)
• Humidity: 20 to 95% Relative humidity
Regulatory Standards
EN 60601 1: 2005 + CORR. 1:2006 + CORR. 2:2007 + AM1:2012
EN 60601-1-2:2007+AC: 2010
Guidance and Manufacturer’s Declaration
Below cables information are provided for EMC reference.
Cable Max. cable length, Number Cable
Shielded/unshielded classification
DC Power Line 0.92m Shielded 1 Set DC Power
Filter Range
Specifications
ITEM CONTENT
Sensor: Piezoelectric sound transducer activated by polycarbonate diaphragm
Voltage: 3.7V Li-polymer
Power Dissipation: 0.115VA (3.7V * 31mA)
Microphone 5Hz - 5,000Hz
Filter Range: Bell Mode 15Hz - 200Hz
Diaphragm Mode 100Hz - 500Hz
Battery Life 20 hours under continuous power on
Charging Time 70 minutes
Amplifier Amplification range 6dB - 18dB
Control Volume Control Volume Digital volume (8 step), 3dB/step
8

Important information regarding electromagnetic compatibility (EMC)
This electrical medical equipment needs special precautions regarding EMC and should
be put into service according to the EMC information provided in the user manual. The
equipment conforms to this IEC 60601-1-2:2014 standard for both immunity and emissions.
Nevertheless, special precautions need to be observed:
Warning: The equipment is intended used in professional healthcare facility environment
except for near active HF SURGICAL EQUIPMENT and the RF shielded room of an ME
SYSTEM for magnetic resonance imaging, where the intensity of EM DISTURBANCES is high.
Essential Performance of the device includes supplying continuous sound output during a
medical evaluation equal to or below 92.1 dB.
Warning: Use of this equipment adjacent to or stacked with other equipment should be
avoided because it could result in improper operation. If such use is necessary, this
equipment and the other equipment should be observed to verify that they are operating
normally.
Warning: The use of accessories, transducers and cables other than those specified or
provided by the manufacturer of this equipment could result in increased electromagnetic
emissions or decreased electromagnetic immunity of this equipment and result in improper
operation.
Warning: Portable RF communications equipment (including peripherals such as antenna
cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of
the 658, including cables specified by the manufacturer. Otherwise, degradation of the
performance of this equipment could result.
Warning: When the AC input voltage is interrupted, the equipment will shut down and if the
power supply restored, it should be recovered by operator manually. This degradation could
be accepted because it will not lead to unacceptable risks and it will not result in the loss of
basic safety or essential performance.
Warning: Accessories and cables provided with this device have not been tested or verified
for use with other medical electrical equipment and should not be considered interchangeable.
9

Table 1 - Emission
Phenomenon Compliance Electromagnetic environment
RF emissions CISPR 11 Professional healthcare
Group 1, Class B facility environment
Harmonic distortion IEC 61000-3-2 Professional healthcare
Class A facility environment
Voltage fluctuations IEC 61000-3-3 Professional healthcare
and flicker Compliance facility environment
EMI Compliance Table (Table 1)
Table 2 - Enclosure Port
Phenomenon Basic EMC Standard
Immunity test levels
Professional healthcare
facility environment
Electrostatic discharge IEC 61000-4-2 ±8 kV contact
±2kV, ±4kV, ±8kV, ±15kV air
Radiated RF EM field IEC 61000-4-3
3V/m
80MHz-2.7GHz
80% AM at 1kHz
Proximity fields from RF wireless IEC 61000-4-3 Refer to table 3
communications equipment
Rated power frequency IEC 61000-4-8 30A/m
magnetic fields 50Hz or 60Hz
EMS Compliance Table (Tables 2-4)
10

Table 3 – Proximity elds from RF wireless communications equipment
Test Frequency Band Immunity test levels
(MHz) (MHz) Professional healthcare
facility environment
385
450
710
745
780
810
870
930
1720
1845
1970
2450
5240
5500
5785
380-390
430-470
704-787
800-960
1700-1990
2400-2570
5100-5800
Pulse modulation 18Hz, 27V/m
FM, ±5kHz deviation, 1kHz sine, 28V/m
Pulse modulation 217Hz, 9V/m
Pulse modulation 18Hz, 28V/m
Pulse modulation 217Hz, 28V/m
Pulse modulation 217Hz, 28V/m
Pulse modulation 217Hz, 9V/m
Table 4 – Input a.c. power Port
Phenomenon Basic EMC Standard
Immunity test levels
Professional healthcare
facility environment
Electrical fast transients/burst IEC 61000-4-4
Surges line-to-line IEC 61000-4-5
Conducted disturances IEC 61000-4-6
induced by RF fields
Voltage dips IEC 61000-4-11
Voltage interruptions IEC 61000-4-11
±2 kV
100kHz repetition frequency
±0.5 kV, ±1 kV
3V, 0.15MHz-80MHz
6V in ISM bands between 0.15MHz
and 80MHz
80%AM at 1kHz
0% UT; 0.5 cycle
At 0º, 45º, 90º, 135º, 180º, 225º, 270º
and 315º
0% UT; 1 cycle
and
70% UT; 25/30 cycles
Single phase: at 0º
0% UT; 250/300 cycles
11

IB p/n 93-658-00 rev 2 EN
Inspected, assembled and
packaged in the U.S.A.
Chestpiece made in China
Headset made in Taiwan
tel: [phone]
toll free: 1-800-232-2670
fax: [phone]
www.adctoday.com
email: [e-mail]
ADC®
55 Commerce Drive
Hauppauge, NY 11788
0044 Printed in the U.S.A.
Warranty
ADC® warrants its products against defects in materials and workmanship under normal use
and service as follows:
1.Warranty service extends to the original purchaser from the date of purchase.
2 years - Electronic Chestpiece
Lifetime - Binaurals & Tubing
2.The entire stethoscope is warranted. This warranty is only valid if the product is registered
online at www.adctoday.com.
What Is Covered: Repair, or replacement of parts, and labor.
What Is Not Covered: Transportation charges to ADC. Damages caused by abuse,
misuse, accident, or negligence, incidental, special, or consequential damages. Batteries or
damage from old batteries is not covered by the warranty. Some states do not allow the
exclusion or limitation of incidental, special, or consequential damages, so this limitation
may not apply to you.
To Obtain Warranty Service: Send item postage paid to ADC, Attn: Service Dept., 55
Commerce Dr., Hauppauge, NY 11788. Please include your name and
address, daytime phone no., proof of purchase, and a brief note explaining the problem.
Implied Warranty: Any implied warranty shall be limited in duration to the terms of this
warranty and in no case beyond the original selling price (except where prohibited by law).
This warranty gives you specific legal rights and you may have other rights which vary from
state to state.
©2019 ADC®. All rights reserved. No one is permitted to reproduce or duplicate in any form, this manual or any part
thereof without the expressed written permission of ADC. ADC assumes no responsibility for any injury to anyone, or for
any illegal or improper use of the product that may result from failure to use the product in accordance with the instruc-
tions, cautions, warnings, or statement of intended use published in this manual.
12