ADC WorldDSL UTU-702C User manual

WorldDSL
WorldDSL
QUICK INSTALLATION GUIDE
HDSL
G.703
SYNC
ALM
HDSL
I/F
LOCLPBK
V.24
REM
ALM
SYNC
ALM
ALM
HDSL
I/F
LPBK
LOC
REM
WorldDSL
UTU-702C List 1
Rate Selectable Line Unit
Part Number: 150-1422-02C
ETU-752C List 1
Rate Selectable Desktop Unit
Part Number: 150-1432-02C

700-702-900-04, Revision 04
ii June 14, 2002 UTU-702C and ETU-752C List 1
Revision History of This Guide
Copies of this document or the UTU/ETU user manual (700-702-100-xx) can
be downloaded from the ADC website at www.adc.com.
Copyright
June 14, 2002
© 2002 ADC DSL Systems, Inc. All rights reserved.
Trademark Information
ADC is a registered trademark and WorldDSL is a trademark of ADC
Telecommunications, Inc. No right, license, or interest to such trademarks is granted
hereunder, and you agree that no such right, license, or interest shall be asserted by
you with respect to such trademark.
Other product names mentioned in this document are used for identification purposes
only and may be trademarks or registered trademarks of their respective companies.
Disclaimer of Liability
Information contained in this document is company private to ADC DSL Systems, Inc.,
and shall not be modified, used, copied, reproduced or disclosed in whole or in part
without the written consent of ADC.
Contents herein are current as of the date of publication. ADC reserves the right to
change the contents without prior notice. In no event shall ADC be liable for any
damages resulting from loss of data, loss of use, or loss of profits, and ADC further
disclaims any and all liability for indirect, incidental, special, consequential or other
similar damages. This disclaimer of liability applies to all products, publications and
services during and after the warranty period.
Revision Release Date Revisions Made
1March 23, 1999 Initial release
2April 16, 1999 Revised label descriptions
3June 21, 1999 Added pinouts for ETU-752 HDSL line and console
port connectors.
4June 14, 2002 ADC rebranding

700-702-900-04, Revision 04 Using This Guide
UTU-702C and ETU-752C List 1 June 14, 2002 iii
USING THIS GUIDE
The following conventions are used in this guide:
•Monospace type indicates screen text.
•Keys you press are indicated by small icons such as or . Key
combinations to be pressed simultaneously are indicated with a plus sign
as follows: + .
•Items you select are in bold.
Three types of messages, identified by icons, appear in text.
UNPACK AND INSPECT YOUR SHIPMENT
Upon receipt of the equipment:
•Unpack each container and inspect the contents for signs of damage. If
the equipment has been damaged in transit, immediately report the extent
of damage to the transportation company and to ADC DSL Systems, Inc.
Order replacement equipment, if necessary.
•Check the packing list to ensure complete and accurate shipment of each
listed item. If the shipment is short or irregular, contact ADC DSL
Systems, Inc. as described in “Product Support” on page 21. If you must
store the equipment for a prolonged period, store the equipment in its
original container.
Notes contain information about special circumstances.
Cautions indicate the possibility of personal injury or
equipment damage.
Warnungszeichen deuten darauf hin, dass Schaden am Gerät
oder eine mögliche Körperverletzung riskiert wird, falls die
Warnungen nicht beachtet werden.
The Electrostatic Discharge (ESD) symbol indicates that a
deviceorassemblyissusceptibletodamagefromelectrostatic
discharge.
YENTER
CTRL ESC

Unpack and Inspect Your Shipment 700-702-900-04, Revision 04
iv June 14, 2002 UTU-702C and ETU-752C List 1

700-702-900-04, Revision 04 Table of Contents
UTU-702C and ETU-752C List 1 June 14, 2002 v
TABLE OF CONTENTS
Overview _______________________________________________ 1
Rate Selectable HDSL ............................................................. 1
UTU-702C Line Unit............................................................... 1
ETU-752C Desktop Unit ......................................................... 2
Interoperability......................................................................... 2
Transmission Ranges ............................................................... 2
Compatibility ........................................................................... 3
Shelves and Enclosures for UTU-702C .................... 3
Connector Adapters for ETU-752C........................... 3
Front Panels ............................................................................. 4
ETU-752C Rear Panel ............................................................. 7
Installation _____________________________________________ 8
Inspection................................................................................. 8
Safety ....................................................................................... 8
Line Unit Installation ............................................................... 9
Desktop Unit Installation ......................................................... 9
HDSL Startup and Synchronization....................................... 11
System Configuration____________________________________ 12
Maintenance Terminal Connection........................................ 12
Logging On ............................................................................ 13
Navigating Menus.................................................................. 14
System Settings...................................................................... 15
LTU and NTU Interface Settings........................................... 16
Viewing Status _________________________________________ 17
Main Console Screen ............................................................. 17
Monitor Screens..................................................................... 19

List of Figures 700-702-900-04, Revision 04
vi June 14, 2002 UTU-702C and ETU-752C List 1
Monitor LTU and NTU Interface Screens ...............19
Monitor HDSL Span Screen ....................................20
Product Support_________________________________________21
Certification and Warranty _________________ Inside Back Cover
LIST OF FIGURES
UTU-702C Front Panel...........................................................................4
UTU-752C Front Panel...........................................................................4
ETU-752C Rear Panel ............................................................................7
UTU/ETU Console Port and Maintenance Terminal
Connector Pinouts..........................................................................13
LIST OF TABLES
Transmission Ranges with ETSI Noise ..................................................2
UTU and ETU Front Panel Components................................................5
UTU and ETU Front Panel LED Indications..........................................6
ETU-752C Rear Panel Components.......................................................7
Console Screen Navigation Keys .........................................................14
Settings in Config System Settings Menu ............................................15
Settings in Config LTU and Config NTU Interface Menus .................16
Information Displayed in Main Console Screen...................................17
Information Displayed in Monitor LTU and NTU Interface Screens ..19
Information Displayed in Monitor HDSL Span 1 Screen.....................20

700-702-900-04, Revision 04 Overview
UTU-702C and ETU-752C List 1 June 14, 2002 1
OVERVIEW
This guide contains installation information for the ADC WorldDSL™RS
UTU-702C List 1 andETU-752C List 1 Rate Selectable (RS) line and desktop
units.
RATE SELECTABLE HDSL
WorldDSL RS is a single pair High-bit-rate Digital Subscriber Line (HDSL)
solution that offers extended reach capabilities through the use of
industry-leading multi-rate DSL technology. The UTU-702C and ETU-752C
deploy HDSL in networks using a single pair of copper wire running at speeds
between 64 kbps and 2048 kbps. The HDSL line rates are either menu
selected in time slot increments of 64 kbps or derived automatically from the
Terminal Transmission (TT) clock received at the Nx64k serial data port from
the Network Data Terminal Equipment (DTE). Transmission ranges vary
according to the rate selected. Depending on noise environment, ranges of up
to 8.5 km (5.3 miles) are possible at the lowest-selectable HDSL line rates
(64 and 128 kbps).
UTU-702C LINE UNIT
The UTU-702C can be configured as a Line Termination Unit (LTU) or
Network Termination Unit (NTU). The default configuration is NTU.
When configured as an LTU, the UTU-702C serves as the Exchange Office
side of a repeaterless, HDSL transmission system. The LTU-configured unit
connects to an NTU-configured unit (UTU-702C or ETU-752C) over one
twisted-pair of copper wire, completing the HDSL transmission system.
The UTU-702C has an Nx64k serial data interface with user-selectable
protocols that include V.35, V.36, X.21, and RS-530 (RS-449). The
UTU-702C accepts the DTE payload at its Nx64k serial data port and
transports the data to the remote unit at the selected HDSL rate. The
UTU-702C requires -36 to -72 Vdc from a local power supply or an
enclosure’s AC-to-DC power supply; it does not supply power to other HDSL
units.
WorldDSL RS units are not backward compatible with
standard HDSL or management unit firmware. The installed
firmware must be that designed for rate selectable units.
WorldDSL RS units must have the same payload rates
available. An LTU set for a rate of 768 kbps will not function
with an NTU whose maximum available rate is 256 kbps.

Overview 700-702-900-04, Revision 04
2 June 14, 2002 UTU-702C and ETU-752C List 1
ETU-752C DESKTOP UNIT
The ETU-752C is housed in a plastic enclosure with interface and power
connectors for use as an integrated desktop unit. All functions of the
ETU-752C, with exception of power requirements, are identical to the
UTU-702C. The ETU-752C requires a source of 100 to 240 volt, 50 or 60 Hz,
AC power.
INTEROPERABILITY
The UTU-702C and ETU-752C are interoperable with the UTU-702 and/or
ETU-752.
TRANSMISSION RANGES
Transmission ranges assume the presence of noise according to the ETSI
model described in TS 101 135. The expected Bit Error Rate (BER) under this
model is 10-7. The transmission ranges in such a noise environment at the
various HDSL line rates over one twisted-pair of 0.4 mm and 0.51 mm copper
wire are listed below.
‘
Transmission Ranges with ETSI Noise
Wire Size and Transmission Range (with ETSI Noise)
HDSL Line
Rate (kbps) (a)
0.4mm (26 AWG)
Single Twisted-Pair
Copper Wire
0.51mm (24 AWG)
Single Twisted-Pair
Copper Wire
128 5.0 km (16,404 ft.) 6.3 km (20,669 ft.) (b)
256 4.1 km (13,451 ft.) 5.1 km (16,732 ft.)
384 3.9 km (12,795 ft.) 4.7 km (15,420 ft.)
512 3.5 km (11,483 ft.) 4.5 km (14,764 ft.)
768 3.2 km (10,499 ft.) 4.1 km (13,451 ft.)
1152 2.6 km (8,530 ft.) 3.4 km (11,155 ft.)
1536 2.2 km (7,218 ft.) 2.9 km (9,514 ft.)
2048 1.9 km (6,234 ft.) 2.3 km (7,546 ft.)
(a) A selected HDSL line rate of 64 kbps is transmitted at 128 kbps.
(b) The maximum no-noise transmission range is approximately 8.5 km.

700-702-900-04, Revision 04 Overview
UTU-702C and ETU-752C List 1 June 14, 2002 3
COMPATIBILITY
The UTU-702C and ETU-752C are compatible with the following ADC
WorldDSL products.
Shelves and Enclosures for UTU-702C
•EMS-830 Exchange Office Management Shelf, rear connector access
(part number 150-1400-01).
•EMS-831 Exchange Office Management Shelf, front connector access
(part number 150-1401-01).
•EMS-832 Exchange Office Management Shelf, front connector access
(part number 150-1402-01).
•ERE-810 Single-Slot Remote Enclosure
(part number 150-1410-01).
•ERE-811 Single-Slot Remote Enclosure with internal AC power supply
(part number 150-1411-01).
•ERE-821 Dual-Slot Remote Enclosure with internal AC power supply
(part number 150-1416-01).
•ERE-826 Single-Slot Remote Enclosure
(part number 150-1412-01).
Connector Adapters for ETU-752C
•ECA-800 D25M to M34F connector adapter for V.35
(part number 150-1470-01).
•ECA-801 D25M to D15F connector adapter for X.21
(part number 150-1471-01).
•ECA-802 DB9M to RJ-45 connector adapter for HDSL
(part number 150-1472-01).
•ECA-804 DB9M to 4-position terminal block connector for HDSL
(part number 150-1474-01).
•ECA-807 DB25M to DB37F connector adapter for RS-449
(part number 150-1477-01).

Overview 700-702-900-04, Revision 04
4 June 14, 2002 UTU-702C and ETU-752C List 1
FRONT PANELS
The components on the UTU-702C and ETU-752C front panels are shown
below. Their functions are described on page 5 and page 6.
UTU-702C Front Panel
UTU-752C Front Panel
UTU-702C
V.24 (RS-232) console port
Warranty control
number label
Bar code label
(located on circuit
side of line card)
I/F ALM LED
HDSL LEDs
Loopback LEDs and
push buttons
LPBK
LOC
REM
I/F
SYNC
ALM
ALM
HDSL
Nx64k
V.24
HDSL LEDs Loopback LEDs and pushbuttons V.24 (RS-232) console port
HDSL
SYNC
ALM
HDSL I/F
LOC LPBK REM
ALM
Unit ID and bar code labels (on bottom of unit)
ALM LEDI/F
Nx64k
WorldDSL

700-702-900-04, Revision 04 Overview
UTU-702C and ETU-752C List 1 June 14, 2002 5
UTU and ETU Front Panel Components
Item Function
HDSL SYNC LED Displays synchronization state for the HDSL loop.
HDSL ALM LED Displays alarm state for the HDSL loop.
I/F ALM LED Displays the Nx64k interface (I/F) alarm state.
LOC LPBK LED Displays local (LOC) loopback state.
LOC LPBK Button Activates the local HDSL analog loopback.
REM LPBK LED Displays remote (REM) loopback state.
REM LPBK Button Activates the remote interface loopback.
V.24 (RS-232) console
port Provides bi-directional communication between the unit and an external maintenance terminal through a V.24 (RS-232C)
interface to allow configuration and performance monitoring
through the console screen menus.
Bar code label (all units) Contains the serial number and part number of the unit, as
indicated in both bar code and text format. Also contains the
configuration number of the unit, as indicated by "CFG: Rnn,"
where nn is the configuration number. For example, CFG: R07
would indicate configuration number 07.
Warranty control
number label (UTU-702C) Indicates the beginning year and month of the line card warranty. Also indicates the line card revision number. For
example, warranty control number "803R07" would indicate a
warranty beginning in the year 1998 (8), during the month of
March (03), and line card revision number R07.
Unit ID label (ETU-752C) Identifies the model number, manufacturer, part number, and
input voltage range of the ETU.

Overview 700-702-900-04, Revision 04
6 June 14, 2002 UTU-702C and ETU-752C List 1
UTU and ETU Front Panel LED Indications
LED Mode Description
HDSL SYNC LED Steady green
Slow flashing
Off
HDSL loop is ready to transmit and
receive data across all spans.
HDSL loop acquisition is in progress for
local span.
HDSL loop is not configured.
HDSL ALM LED Steady red
Pulsing red
Off
Indicates:
•Loss of sync word (LOSW)
•Margin is below the set margin alarm
threshold
•Errored Seconds (ES) count is above
threshold on any span.
Pulses for every ES on any span.
Normal transmit or receive data is in
progress.
I/F ALM LED Steady red Loss of Clock (LOC) alarm due to loss of
TT clock (Nx64k timing) or external clock
(EXT timing).
For information on loopback testing and loopback LED
indications, see the WorldDSL RS Rate Selectable HDSL
Line and Desktop Units user manual, section 700-702-100-xx.
This document can be downloaded from the ADC website at
www.adc.com.

700-702-900-04, Revision 04 Overview
UTU-702C and ETU-752C List 1 June 14, 2002 7
ETU-752C REAR PANEL
The components on the ETU-752C rear panel are shown and described
below.
ETU-752C Rear Panel
ETU-752C Rear Panel Components
Item Description
D25F data port connector Connects Nx64k data circuits to the enclosure.
D9F HDSL line connector Connects the HDSL pairs to the enclosure.
Power cord receptacle Connects an AC power cord to the enclosure.
On/Off switch Rocker switch that allows you to turn the externally applied
AC power on or off.

Installation 700-702-900-04, Revision 04
8 June 14, 2002 UTU-702C and ETU-752C List 1
INSTALLATION
This section contains instructions for installation of the UTU-702C line unit
and the ETU-752C desktop unit.
INSPECTION
Before installing the line or desktop unit, inspect it for signs of damage. If the
unit has been damaged in transit, immediately report the extent of the damage
to the transportation company and to ADC DSL Systems, Inc.
SAFETY
To ensure your safety when servicing and installing this equipment, please
take the following precautions:
Be careful when installing or modifying telephone lines.
Dangerous voltages can be present. It is unsafe to install
telephone wiring during a lightning storm.
Always disconnect all telephone lines and power connections
before servicing or disassembling this equipment. For
performance and safety reasons, only power supplies listed
for use with telephone equipment by a locally recognized
organization should be used with ADC equipment. All wiring
external to the product should follow the local wiring codes.
Walte Vorsicht beim Installieren oder Ändern von
Telefonlinien. Gefährliche Spannungen könnten anliegen. Es
ist nicht sicher während eines Gewitters Telefondräte zu
installieren.
Bevor Wartung oder Auseinandernehmen des Gerätes
müssen immer alle Telefon- und Netzkabel ausgezogen
werden. Aus Leistungs- und Sicherheitsgründen sollten nur
Netzteile die für Telefongeräte zugeschnitten und von einem
renommierten Geschäft vertrieben werden mit ADC Geräten
verwendet werden. Alle externen Verdrahtungsarbeiten
sollten nach den hiesigen Elektrizitätsvorschriften ausgeführt
werden.

700-702-900-04, Revision 04 Installation
UTU-702C and ETU-752C List 1 June 14, 2002 9
LINE UNIT INSTALLATION
To install the UTU-702C line unit into a shelf or remote enclosure:
1Install the line unit into the appropriate slot (1 through 16) of a shelf or
into a single- or dual-slot remote enclosure. (See “Compatibility” on
page 3.)
2Connect the power source as instructed in the technical practice for the
shelf or remote enclosure in which the line unit is installed.
3If configuring the line unit as an LTU, power up the shelf and proceed as
instructed on pages 12 through 15 to access the Local Unit Role option
in the Config System Settings menu (the default setting is NTU).
4Connect the data port and HDSL line cabling as instructed in the
technical practice for the shelf or remote enclosure in which the line unit
is installed.
5Set the DTE interface (TT clock) for the default HDSL payload rate of
256 kbps (4 time slots).
DESKTOP UNIT INSTALLATION
To install an ETU-752C desktop unit:
1Insert the AC power cord into the power cord receptacle on the ETU rear
panel.
2Plug the power cord into a source of 100 to 240 volt, 50 or 60 Hz
AC power.
3If configuring the desktop unit as an LTU, power up the unit and proceed
as instructed on pages 12 through 15 to access the Local Unit Role option
in the Config System Settings menu (the default setting is NTU).
The chassis ground of the shelf or remote enclosure
receiving these units must be connected to earth ground for
protection of the equipment and for safety of personnel.
Other protection is required when the network side of the
equipment is extended to an outside facility.

Installation 700-702-900-04, Revision 04
10 June 14, 2002 UTU-702C and ETU-752C List 1
4Connect the data port cable from the DTE to the data port connector on
the ETU-752C rear panel.
5Connect the HDSL line cable to the HDSL line connector on the ETU
rear panel. The pinouts for the HDSL line connector are listed in the
following table.
6Set the DTE interface (TT clock) for the default HDSL payload rate of
256 kbps (4 time slots).
HDSL Line Connector (DB9F) Pinouts
Pin* Signal Description
4HDSL_RING_A HDSL Ring Loop 1
9HDSL_TIP_A HDSL Tip Loop 1
1HDSL_RING_B HDSL Ring Loop 2
6HDSL_TIP_B HDSL Tip Loop 2
* No other pins are used.

700-702-900-04, Revision 04 Installation
UTU-702C and ETU-752C List 1 June 14, 2002 11
HDSL STARTUP AND SYNCHRONIZATION
At startup, a WorldDSL RS LTU confirms that it is communicating with a
WorldDSL RS NTU. The LTU then synchronizes the NTU configuration
with its own configuration.
Power up the LTU and NTU. The following synchronization sequence should
occur:
1Power up the shelf or enclosure where the unit(s) are installed.
2Confirm the following:
•The HDSL ALM LED is on and the HDSL SYNC LED flashes once
per second as the units self-configure and establish synchronization.
•After approximately 60 seconds the HDSL ALM LED is off and the
HDSL SYNC LED is a steady green. The units are now ready for
configuration through the console screen menus.
If the HDSL SYNC LED continues to flash after 90 seconds,
the HDSL line is faulty, the Local Unit Role is not configured
as LTU, or one of the units isnot a rate selectable unit. Check
for the correct line units and Local Unit Role. Test the HDSL
line using the loopbacks described in technical practice
700-702-100-xx.
The LTU and NTU will reset and their LEDs will sequence
through the startup cycle following any change to the HDSL
Payload Rate option (see “System Settings” on page 15).

System Configuration 700-702-900-04, Revision 04
12 June 14, 2002 UTU-702C and ETU-752C List 1
SYSTEM CONFIGURATION
After synchronization is established, the HDSL system can be configured and
performance can be monitored from the local unit. If the HDSL link is down,
the only parameters that can be changed are those on the local unit. The LTU
also provides a special lockout feature that prevents users plugged into the
NTU console port from changing the circuit configuration. When enabled, the
maintenance terminal connected to an NTU provides a read-only view of the
entire HDSL system.
MAINTENANCE TERMINAL CONNECTION
A maintenance terminal is used to access the line unit console screen menus.
Through these menus, the HDSL system is configured, monitored, tested, and
its circuit inventory is displayed.
To connect a maintenance terminal:
1Connect a standard serial cable from the maintenance terminal COM port
to the line unit’s front panel console port. The pinouts for the console port
and maintenance terminal connectors are shown in the diagram on the
following page.
2Configure the maintenance terminal for the following communication
settings:
•VT100 Emulation or ANSI (if VT100 is not available)
•clear the modem initialization string if supported by the terminal
•Bits per second: 1200, 2400, 4800, 9600 (default), or 19200 bps
(recommended)
•Data bits: 8
•Parity: None
•Stop bits: 1
•Flow Control: None
The console screen menus are not available when the HDSL
line unit is under the control of a shelf management unit.

700-702-900-04, Revision 04 System Configuration
UTU-702C and ETU-752C List 1 June 14, 2002 13
UTU/ETU Console Port and Maintenance Terminal Connector Pinouts
LOGGING ON
To log on to the maintenance terminal console screen:
1Press the several times to activate the autobaud feature and
to display the Logon Password screen.
2Type the password at the prompt or press if a password has not
been established. The console screen menu bar displays.
The key is the factory default password. If you
establish a different password, you must type the new
password (single word, no spaces, up to eight characters) on
a subsequent log on. If the system does not respond, verify
that the Hardware Flow Control of the maintenance terminal
is set to NONE.
SPACEBAR
ENTER
ENTER

System Configuration 700-702-900-04, Revision 04
14 June 14, 2002 UTU-702C and ETU-752C List 1
NAVIGATING MENUS
Use the keys described in the following table to navigate the console screen
and its menus.
Console Screen Navigation Keys
These Keys Perform this Function
Alpha-numeric
keys Type the underlined or highlighted letter to select and execute a menu item. For example on the console screen menu bar, type to access
the Config drop-down menu.
Also use these keys to enter values in text fields. For example, on the
Config Date and Time menu, type the date in a DD/MM/YY format.
and keys Press the key to access a console screen drop-down menu. For
example, press the key on Config to access the Config drop-down
menu. Or press the and keys to highlight a sub-menu item, then
press to select the item. For example, press the key to
highlight Config Alarms, then press to view the sub-menu.
key Provides same function as the key.
and keys Moves horizontally across the Menu bar, except when in a text entry
field.
++ moves up one line in the History screens.
++ moves down one line in the History screens.
++ performs the page-down function in the History screens.
++ performs the page-up function in the History screens.
Selects options displayed for current menu item. For example, to select
MANUAL or Nx64k AUTO mode from the Config System Settings
menu:
• press the key to highlight the HDSL Rate Mode option, then
• press the until the desired option (MANUAL or Nx64k
AUTO) is highlighted.
Exits the current screen and returns to the previous screen. Selection
changes made on the current screen are discarded. Press while
in a text field to cancel the text entry and restore the old value.
Applies all selections on the current screen. For example, to select an
HDSL payload rate from the Config System Settings menu:
• press the key to highlight the HDSL Payload Rate option, then
• type the desired number of time slots (1 to 32) and press
to display the selected HDSL payload rate (in MANUAL mode only).
C
↑ ↓ ↓
↓
↑ ↓
ENTER ↓
ENTER
TAB ↓
← →
CTRL ECTRL E
CTRL XCTRL X
CTRL CCTRL C
CTRL RCTRL R
SPACEBAR
↓
SPACEBAR
ESC
ESC
ENTER
↓
ENTER