ADEMCO Ademco VISTA-40 Operating instructions

N7001PRV4 7/98
VISTA-40
2-Partition
Security System
Programming Guide
Single Partition and 2-Partition
Programming Forms
®

Page 2
TABLE OF CONTENTS
SINGLE PARTITION PROGRAMMING FORM................................................................................3
TWO-PARTITION PROGRAMMING FORM.....................................................................................7
SYSTEM-WIDE DATA FIELDS..........................................................................................................8
PARTITION-SPECIFIC DATA FIELDS .............................................................................................11
PROGRAMMING WITH #93 MENU MODE (Overview))..............................................................13
CHANGING ZONE RESPONSE TYPE & REPORT CODES (EXPERT MODE).......................14
SYSTEM LAYOUT WORKSHEETS..............................................................................................16
Other Documents Provided With The VISTA-40
Document Purpose and Content
Installation
Instructions Use the Installation Instructions portion of this manual when installing the hard-ware components of the installation, including hardwired zones, wireless transmitters,
powering the control, etc. Use the Programming Procedures section of the
installation manual when programming the system. It provides detailed programming
procedures and descriptions of all data fields. It also provides detailed procedures for
using #93 Menu Mode.
A Summary Of Connections Diagram is provided at the back of the Installation
Instructions.
User’s Manual Intended for the end user, this manual provides procedures for system operation.
This Programming Guide includes basic programming information, a brief overview of the
programming procedure with #93 Menu Mode, Changing Response type & Report Codes (Expert
Mode), Single and 2-Partition Programming Forms, plus System Layout Worksheets.
Two programming forms are provided: A Single Partition Form and a 2-Partition Form.
• Make sure that one alpha or voice/alpha keypad is connected to the control and is set to device address
"00."
Single Partition System
• The system default is for a single partition system. Use the SINGLE PARTITION PROGRAMMING FORM
beginning on page 4 when programming for single partition usage.
Two-Partition System
• You must enter "2" in data field 2✱00 to set the system for two partitions. Use the 2-PARTITION
PROGRAMMING FORM beginning on page 8 when programming the system for two partitions.
# 93 Menu Mode
• Because the control supports various types of input devices (such as button type transmitters, serial
number polling loop devices, etc.), zone characteristics, including zone response types and report codes,
must be programmed using the #93 Menu Mode procedure.
• In addition to programming zone information, #93 Menu Mode is required for enrolling serial numbers,
programming alpha descriptors, programming device characteristics and for programming relay output
functions.
• Refer to the separate Installation and Setup Guide for detailed procedures when using #93 Menu Mode.

Page 3
VISTA-40 SINGLE PARTITION PROGRAMMING FORM
Use the Single Partition Programming Form only if your system is set up as a single
partition system.
For 2-partition systems, use the form titled "VISTA-40 Two-Partition Programming Form."
Steps To Programming a Single Partition VISTA-40 System
IMPORTANT: A 2-Line Alpha keypad is required for programming the VISTA-40.
Make sure that one alpha keypad is connected to the control and is set to device address "00."
1. Enter Programming Mode (enter installer code + [8] + [0] + [0]).
2. Program the data fields shown on the programming form.
NOTE: Zone Response Type and Report Code fields will automatically appear during normal
programming, but must be skipped if the zone has not been previously programmed using #93 Menu
Mode (see step 3 below). These fields are bordered by a dotted line on the programming forms and
include:
✱02 - ✱05 and 1✱01 - 1✱09 ASSIGN RESPONSE TYPES
✱54 - ✱78 REPORT CODES
To skip these fields when they appear, press [✱] plus the next data field number to be programmed. For
example, to skip fields ✱02 - ✱05 in a one partition system, press [✱] plus "09." Field ✱09 ENTRY DELAY
#1 appears.
3. Enter #93 Menu Mode by pressing #93 while in programming mode, then do the following in the order
presented:
• Use the DEVICE PROG. prompts to program device addresses and characteristics.
• Use the ZONE PROG. prompts to program zone information.
• Use the RELAY PROG. prompts to program relay output information.
• Use the ALPHA PROG. prompts to program alpha descriptors.
• Use the SERIAL # PROG prompts to program sensor device serial numbers.
• Use RLY VOICE DESCR. prompts to program relay voice descriptors, if the 4285 Phone Module is
used.
• Use the CUSTOM INDEX prompts to program custom word substitutes, if the 4285 Phone Module is
used.
Refer to the #93 Menu Mode section of the separate INSTALLATION INSTRUCTIONS document for
detailed procedures when using #93 Menu Mode. A brief overview of this mode is provided later in this
document.
SUMMARY OF PROGRAMMING COMMANDS
• To enter program mode, enter installer code + [8] + [0] + [0]
• To set standard defaults, press ✱97
• To set communication defaults, press ✱94 + one of the following: ✱80=low speed; ✱81=Ademco
Express; ✱82=Ademco High Speed; ✱83=Ademco's Contact ID
• To change to next page of program fields, press ✱94
• To return to previous set of fields, press ✱99
• To erase account & phone number field entries, press [✱] + field number + [✱]
• To assign zone descriptors, press #93 + follow menu prompts
• To add custom words, press #93 + follow menu prompts
• To enter Installer's Message, press #93 + follow menu prompts
• To exit program mode, press ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code.
✱98 prevents re-access to programming mode by installer code.

Page 4
VISTA-40 SINGLE PARTITION PROGRAMMING FORM
Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.
✱00 INSTALLER CODE [4140] | | |
Enter 4 digits, 0-9
✱02 - ✱05 ASSIGN RESPONSE TYPE FOR ZONES
Skip these fields. Use #93 Menu Mode, Zone
Programming to program response types.
✱09 ENTRY DELAY #1 [02] |
(00-15 times 15 seconds)
✱10 EXIT DELAY #1 [03] |
(00-15 times 15 seconds)
✱11 ENTRY DELAY #2 [06] |
(00-15 times 15 seconds)
✱12 EXIT DELAY #2 [08] |
(00-15 times 15 seconds)
✱13 ALARM SOUNDER DURATION [04] |
01-15 times 2 minutes . Minimum 4 minutes for UL.
✱14 ZONE 9 FAST/SLOW RESPONSE
1=fast; 0= slow; "0" for UL.
✱15 KEYSWITCH ASSIGNMENT
Enter partition in which keyswitch used, 1-2; 0=disable
✱16 CONFIRMATION OF ARMING DING
1=enable; 0=disable
✱17 AC LOSS KEYPAD SOUNDING
1=yes; 0=no
✱19 RANDOMIZE AC LOSS REPORT
1=randomize 10-40 min.; 0=no
✱20 4285 PHONE MODULE ACCESS CODE | |
Enter 01-09 for 1st digit; 11( for ✴) or 12 (for #) for [00] [11]
2nd digit To disable voice module, enter
1st digit = 00 & 2nd digit = 11
✱21 PREVENT FIRE TIME-OUT
1=no timeout; 0=fire timeout
✱22 KEYPAD PANIC ENABLES [0-0-1]
1=enable; 0=disable 95 96 99
✱23 MULTIPLE ALARMS [1]
1=yes; 0=no
✱24 IGNORE EXPANSION ZONE (RF, RPM) TAMPER
1=disable; 0=enable
✱25 LRR BURG.TRIGGER FOR TYPE 8 [1]
1=enable; 0=disable
✱26 INTELLIGENT TEST REPORTING
Set "0" for UL 1=yes, (no report sent if any other report was
recently sent); 0=no
✱27 TEST REPORT INTERVAL [024] | |
Enter interval in hours, 001-199; 000=no report ; Max. 024 for UL.
✱28 POWER UP IN PREVIOUS STATE [1]
1=yes; 0=no; "1" for UL.
✱29 QUICK ARM [1]
1=yes; 0=no
✱30 TOUCH-TONE OR ROTARY DIAL
1=TouchTone; 0=rotary
✱31 PABX ACCESS CODE | | | |
00-09; B-F (11-15)
✱32 PRIM. SUBS. ACCT # | | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
✱33 PRIMARY PHONE NUMBER
Enter 0-9 for each digit, or #11 (✴), #12 (#), #13 (pause)
✱34 SECONDARY PHONE NUMBER
Enter 0-9 for each digit, or #11 (✴), #12 (#), #13 (pause)
✱35 DOWNLOAD PHONE No.
Enter 0-9 for each digit, or #11 (✴), #12 (#), #13 (pause)
✱36 DOWNLOAD ID No.
| | | | | | | |
Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]
✱37 DOWNLOAD COMMAND ENABLES
0
Dialer System Not Remote Remote Remote Upload Download
Shutdwn Shutdwn Used Bypass Disarm Arm Program Program
See field 1✱53 for Callback disable option; [1=enable]; 0=disable; For UL
installations, all options must be disabled.
✱38 PREVENT ZONE XX BYPASS |
01-64; 00 if all zones (except Fire zones) can be bypassed
✱39 OPEN/CLOSE REPORT FOR INSTALLER
1=enable; 0=disable
✱40 OPEN/CLOSE REPORTING FOR KEYSWITCH
1=enable; 0=disable
✱41 NORMALLY CLOSED or EOLR (Zones 2-8) [1]
1=N.C.loops; 0=EOLR supervision; Must be "0" for UL.
✱42 DIAL TONE PAUSE
0=5 seconds; 1=11 seconds; 2=30 seconds; Must be "0" for UL.
✱43 DIAL TONE DETECTION [1]
1=wait for true dial tone; 0=pause, then dial
✱44 RING DETECTION COUNT |
01-14; 15=answering machine; 00=no detection; Do not set to 00 if
voice module is used, or 01 if VIM module is used.
✱45 PRIMARY FORMAT
0=Low Speed; 1=Contact ID; 2=Ademco High Speed;
3=Ademco Express
✱46 LOW SPEED FORMAT (Primary)
0=Ademco Low Speed; 1=Sescoa/Radionics
✱47 SECONDARY FORMAT
0=Low Speed; 1=Contact ID; 2=Ademco High Speed;
3=Ademco Express
✱48 LOW SPEED FORMAT (Sec.)
0=Ademco Low Speed; 1=Sescoa/Radionics
✱49 CHECKSUM VERIFICATION 1=yes; 0=no
Prim Scndry
✱50 SESCOA/RADIONICS SELECT
1=Sescoa; 0=Radionics
✱51 DUAL REPORTING
1=yes; 0=no; If used with Spilt Reporting "1" option (1✱34), alarms
go to both primary & secondary numbers, while all other reports go
to secondary only. If used with Split Reporting "2" option,
open/close and test messages go to both lines, while all other
reports go to primary.
✱52 STANDARD/EXPANDED REPORT FOR PRIMARY
Alarm Rstr Bypass Trbl Opn/Cls Low Bat
0=standard; 1=expanded; Note: Expanded overrides 4+2 format.
✱53 STANDARD/EXPANDED REPORT FOR SECONDARY
Alarm Rstr Bypass Trbl Opn/Cls Low Bat
0=Standard; 1=Expanded; Note: Expanded Overrides 4+2 Format.

Page 5
VISTA-40 SINGLE PARTITION PROGRAMMING FORM
✱54 -✱57 ALARM REPORT CODE & ID DIGITS FOR ZONES
1-16. Skip these fields. Use #93 Menu Mode,
Zone Programming to assign report codes.
✱58 SUPV. & RESTORE CODES for zones 1-16
| Alarm Rst.
| Trouble
| Trble Rst.
| Bypass
| Bypass Rst.
✱59 -✱62 ALARM REPORT CODE & ID DIGITS FOR ZONES
17-32. Skip these fields. Use #93 Menu Mode,
Zone Programming to assign report codes.
✱63 SUPV. & RESTORE CODES for zones 17-32
| Alarm Rst.
| Trouble
| Trble Rst.
| Bypass
| Bypass Rst.
✱64 - ✱67 ALARM REPORT CODE & ID DIGITS FOR ZONES
33-48. Skip these fields. Use #93 Menu Mode,
Zone Programming to assign report codes.
✱68 SUPV. & RESTORE CODES for zones 33-48
| Alarm Rst.
| Trouble
| Trble Rst.
| Bypass
| Bypass Rst.
✱69 -✱72, ALARM REPORT CODE & ID DIGITS FOR ZONES
✱74-✱77 49-99. Skip these fields. Use #93 Menu Mode,
Zone Programming to assign report codes.
SUPV. & RESTORE CODES
✱73 (for zones 49-64) ✱78 (for zones 87-99)
| Alarm Rst. | Alarm Rst.
| Trouble | Trouble
| Trble Rst. | Trble Rst.
| Bypass | Bypass
| Bypass Rst. | Bypass Rst.
ZONE TYPE RESTORE ENABLES 1=enable; [0=disable]
✱79 FOR ZONE TYPES 1-8 ✱80 ZONE TYPES 9/10
12345678 910
SYSTEM NON ALARM CODES
✱81 ✱82
First Digit Second Digit
Close | |
Open | |
Low Battery | |
Low Bat Res | |
AC Loss | |
AC Restore | |
Test | |
Power | |
Cancel | |
Prog. Tamp. | |
Second digit of each
code applies only to
4+2 or expanded (fields
✱52 & ✱53) formats.
✱83 FIRST TEST REPORT TIME | | |
[Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 00-59;
00 in all boxes=instant (Day 01= Monday)
✱84 SWINGER SUPPRESSION [03] |
01-15 alarms ; Must be "00" (disabled) for UL.
✱85 ENABLE DIALER REPORTS
FOR PANICS & DURESS 95 96 99 Duress
1=enable; 0=disable
✱86 4208 MODULE ZONE ASSIGNMENT
1=allows 8 zone numbers (10-17) on one module, but prevents any
other polling loop expansion; 0=Otherwise
✱87 ENTRY WARNING [1]
1=continuous; 0=3 beeps
✱88 BURG. ALARM COMM. DELAY
1=16 seconds; 0=no delay
✱89 RESTORE REPORT TIMING
0=instant; 1=at bell timeout; 2=at disarm
✱90 2nd SUBS. ACCT # | | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
2nd Page Programming Fields
(press ✱94)
1✱01 - 1✱09 ASSIGN RESPONSE TYPE FOR ZONES
Skip these fields. Use #93 Menu Mode, Zone
Programming to assign response types
1✱28 RF TX LOW BATTERY SOUND
1=immediate; 0=when disarmed; Must be "1" for UL
1✱29 RF TX LOW BATTERY REPORT ENABLE
1=enable; 0=disable Must be "1" for UL
1✱30 RF RCVR CHECK-IN INTERVAL [06] |
02-15 times 2 hours; 00 disables supervision
Max. "6" (12 hr) for UL
1✱31 RF TRANSMITTER CHECK-IN INTERVAL[12] |
02-15 times 2 hours; 00 disables transmitter supervision
Max. "6" (12 hr) for UL
1✱32 RF RECEIVER TYPE
1=4281 ; 2=5881; 0=NONE
1✱33 TOUCH-TONE W/ROTARY BACKUP ENABLE
1=enable; 0=disable

Page 6
VISTA-40 SINGLE PARTITION PROGRAMMING FORM
1✱34 COMM. SPLIT REPORT SELECTION
0=no; 1=alarms primary, others secondary;
2=open/close, test secondary, others primary; See ✱51 for notes.
DIALER CODES ( Armed Stay, Time Set & Event Logging)
1✱40 1✱41
First Digit Second Digit
Armed STAY | |
Time/Date set or event log reset | |
1✱43 PERM. KEYPAD BACKLIGHT
1=enable; 0=disable; When disabled, display lights when any
key is pressed, and turns off after period of keypad inactivity.
1✱44 WIRELESS KEYPAD
TAMPER DETECT ENABLE 1=enable; 0=disable
1✱45 EXIT DELAY SOUNDING
1=enable; 0=disable Produces quick beeping during exit delay if
enabled.
1✱46 AUXILIARY OUTPUT MODE
0=ground start; 1=open/close trigger; 2=keypad sounding;
3=Non-Ademco AAV unit trigger
1✱47 CHIME ON EXT SIREN
1=enable; 0=disable
1✱48 WIRELESS KEYPAD ASSIGNMENT
0=disable; enter partition in which RF keypad used, 1-2.
1✱49 SUPPRESS TX SUPERVISION SOUND [1]
1=disable; 0=enable.
Must be "0" for UL.
1✱52 SEND CANCEL IF ALARM + OFF
1=no restriction; 0=within Bell Timeout period only
1✱53 DOWNLOAD CALLBACK
1=callback not required; 0=callback required; Must be "0" for UL.
1✱57 ENABLE 5800 RF BUTTON GLOBAL ARM
Enter "1" to have the system arm/disarm following the button's
user's global arm settings. Enter "0" if the button is not to be used
to global arm the system.
1✱58 ENABLE 5800 RF BUTTON FORCE BYPASS
If zone is faulted after pressing button, keypad will beep once.
User should press button again within 4 sec. to force bypass
those zones. Enter 1 if force bypass is desired. Enter 0 if not
desired.
1✱60 AAV MODULE SELECT
Enter “1” only if AAV unit is used.
NOTE: If enabled zone 5 can no longer be used as a protection
zone.
1✱66 SILENCE BELLS DURING AAV
0 = alarm sounders continue during AAV sessions;
1 = alarm sounders silent during AAV sessions, resume after
AAV session (unless timeout has occurred).
Must be "0" for UL.
1✱70 EVENT LOG TYPES
1=enable logging; 0=disable Alrm Chck Byps O/C Systm
1✱71 12/24 HOUR TIME STAMP FORMAT
0=12 hour; 1=24 hour
1✱74 RELAY TIMEOUT XX MINUTES | |
Enter the relay timeout, 0-127 in multiples of 2 minutes, desired
for #93 Menu Mode Relay Programming output command "56".
1✱75 RELAY TIMEOUT YY SECONDS | |
Enter the relay timeout, 0-127 seconds, desired for #93 Menu
Mode Relay Programming command "57".
1✱76 ACCESS CONTROL RELAY FOR PARTITION |
Enter relay number that will be pulsed for 2 seconds whenever
code + [0] is pressed. Enter 00-08 [00]=none
3rd Page Programming Fields
(press ✱94)
PARTITIONING SETUP FIELDS
2✱00 NUMBER OF PARTITIONS [1]
Enter 1 for single partition systems.
2✱01 DAYLIGHT SAVINGS TIME [04, 10] | |
START/END MONTH Start End
00-12; if no daylight savings time, enter 00,00
2✱02 DAYLIGHT SAVINGS TIME [1, 5] |
START/END WEEKEND # Start | End
Enter 1-7. 1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next to
last; 7=3rd from last [default is 1st Sunday in April, last in Oct.]
2✱17 NUMBER OF CODES PER PARTITION [69] 1 |
Enter 01-69. Total must be less than or equal to 70. [01] 2 |
2✱18 ENABLE GOTO FOR THIS PARTITION
1=enable; 0=disable
2✱19 USE PARTITION DESCRIPTORS
0=disable; 1=enable
2✱20 ENABLE J7 TRIGGERS by PARTITION [1]
0=disable for displayed partition; 1=enable for displayed partition
2✱21 ENABLE SUPERVISION PULSES FOR LRR
TRIGGER OUTPUTS | |
Used for supervised connection to 7920SE. F B S
Enter 0 to disable or 1 to enable the listed outputs.
F= Fire; B= Burglary; S= Silent panic/duress

Page 7
VISTA-40 TWO-PARTITION PROGRAMMING FORM
Use the Two-Partition Programming Form if your system is set up for two partitions.
For single partition systems, use the form titled "VISTA-40 Single Programming Form."
IMPORTANT: A 2-Line Alpha keypad is required for programming the VISTA-40.
Make sure that one alpha keypad is connected to the control and is set to device address "00."
1. Enter Programming Mode (enter installer code + [8] + [0] + [0]).
2. Go to field 2✱00 and enter "2" to set the system for two partitions.
When set for two partitions, there are some data fields that are system-wide (global) and some that are
"partition-specific." The partition-specific fields, shown shaded on the form, can be assigned different
values for each partition, and these fields are automatically skipped when programming system-wide
fields. To program partition-specific fields, see step 4 below.
3. Program the system-wide (global) data fields shown on the main portion of the programming form. These
include all fields except those shown shaded and Zone Response Type and Report Code fields, which
require using #93 Menu Mode to program (see step 5 below).
NOTE: zone response Type and Report Code fields will automatically appear during normal
programming, but must be skipped if the zone has not been previously programmed using #93 Menu
Mode (see step 5 below). These fields are bordered by a dotted line on the programming forms and
include: ✱02–✱05 and 1✱01–1✱09 ASSIGN RESPONSE TYPES
✱54–✱78 REPORT CODES
To skip these fields when they appear, press [✱] plus the next data field number to be programmed. For
example, to skip fields ✱02–✱05, press [✱] plus "14." Field ✱14 ZONE 9 FAST/SLOW RESPONSE
appears.
4. Program the partition-specific data fields by pressing ✱91 and entering the partition number you wish to
program. The first partition-specific field (✱09 ENTRY DELAY #1) for that partition automatically appears.
Refer to the Partition-Specific section of this programming form when programming these fields for each
partition.
5. Enter #93 Menu Mode by pressing #93 while in programming mode, then do the following in the order
presented:
• Use the DEVICE PROG. prompts to program device addresses and characteristics.
• Use the ZONE PROG. prompts to program zone information.
• Use the RELAY PROG. prompts to program relay output information.
• Use the ALPHA PROG. prompts to program alpha descriptors.
• Use the SERIAL # PROG prompts to program sensor device serial numbers.
• Use RLY VOICE DESCR. prompts to program relay voice descriptors, if the 4285 Phone Module is
used.
• Use the CUSTOM INDEX prompts to program custom word substitutes, if the 4285 Phone Module is
used.
Refer to the #93 Menu Mode section of the separate INSTALLATION INSTRUCTIONS document for
detailed procedures when using #93 Menu Mode. A brief overview of this mode is provided later in this
document.
SUMMARY OF PROGRAMMING COMMANDS
• To enter program mode, enter installer code + [8] + [0] + [0]
• To set standard defaults, press ✱97
• To set communication defaults, press ✱94 + one of the following: ✱80=low speed; ✱81=Ademco Express;
✱82=Ademco High Speed; ✱83=Ademco's Contact ID
• To change to next page of program fields, press ✱94
• To return to previous set of fields, press ✱99
• To erase account & phone number field entries, press [✱] + field number + [✱]
• To assign zone descriptors, press #93 + follow menu prompts
• To add custom words, press #93 + follow menu prompts
• To enter Installer's Message, press #93 + follow menu prompts
• To exit program mode, press ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code.
✱98 prevents re-access to programming mode by installer code.
Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.

Page 8
VISTA-40 TWO-PARTITION PROGRAMMING FORM
✱00 INSTALLER CODE [4140] | | |
Enter 4 digits, 0-9
✱02 - ✱05 ASSIGN RESPONSE TYPE FOR ZONES
Skip these fields. Use #93 Menu Mode, Zone
Programming to program response types.
Refer to the Partition-Specific section of this
form for programming shaded fields.
✱09 ENTRY DELAY #1 Partition-Specific
✱10 EXIT DELAY #1 Partition-Specific
✱11 ENTRY DELAY #2 Partition-Specific
✱12 EXIT DELAY #2 Partition-Specific
✱13 ALARM SOUNDER DURATION Partition-Specific
✱14 ZONE 9 FAST/SLOW RESPONSE
1=fast; 0= slow; "0" for UL.
✱15 KEYSWITCH ASSIGNMENT
Enter partition in which keyswitch used, 1-2; 0=disable
✱16 CONFIRMATION OF ARMING DING Partition-Specific
✱17 AC LOSS KEYPAD SOUNDING
1=yes; 0=no
✱19 RANDOMIZE AC LOSS REPORT
1=randomize 10-40 min.; 0=no
✱20 4285 PHONE MODULE ACCESS CODE | |
Enter 01-09 for 1st digit; 11( for ✴) or 12 (for #) for [00] [11]
2nd digit To disable voice module, enter 1st digit = 00 & 2nd digit = 11
✱21 PREVENT FIRE TIME-OUT
1=no timeout; 0=fire timeout
✱22 KEYPAD PANIC ENABLES Partition-Specific
✱23 MULTIPLE ALARMS Partition-Specific
✱24 IGNORE EXPANSION ZONE (RF, RPM) TAMPER
1=disable; 0=enable
✱25 LRR BURG.TRIGGER FOR TYPE 8 [1]
1=enable; 0=disable
✱26 INTELLIGENT TEST REPORTING
Set "0" for UL 1=yes, (no report sent if any other report was
recently sent); 0=no
✱27 TEST REPORT INTERVAL [024] | |
Enter interval in hours, 001-199; 000=no report ; Max. 024 for UL.
✱28 POWER UP IN PREVIOUS STATE [1]
1=yes; 0=no; "1" for UL.
✱29 QUICK ARM Partition-Specific
✱30 TOUCH-TONE OR ROTARY DIAL
1=TouchTone; 0=rotary
✱31 PABX ACCESS CODE | | | |
00-09; B-F (11-15)
✱32 PRIM. SUBS. ACCT # Partition-Specific
✱33 PRIMARY PHONE NUMBER
Enter 0-9 for each digit, or #11 (✴), #12 (#), #13 (pause)
✱34 SECONDARY PHONE NUMBER
Enter 0-9 for each digit, or #11 (✴), #12 (#), #13 (pause)
✱35 DOWNLOAD PHONE No.
Enter 0-9 for each digit, or #11 (✴), #12 (#), #13 (pause)
✱36 DOWNLOAD ID No.
| | | | | | | |
Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]
✱37 DOWNLOAD COMMAND ENABLES
0
Dialer System Not Remote Remote Remote Upload Download
Shutdwn Shutdwn Used Bypass Disarm Arm Program Program
See field 1✱53 for Callback disable option; [1=enable]; 0=disable; For UL
installations, all options must be disabled.
✱38 PREVENT ZONE XX BYPASS Partition-Specific
✱39 OPEN/CLOSE FOR INSTALLER Partition-Specific
✱40 OPEN/CLOSE REPORTING FOR KEYSWITCH
1=enable; 0=disable
✱41 NORMALLY CLOSED or EOLR (Zones 2-8) [1]
1=N.C.loops; 0=EOLR supervision; Must be "0" for UL.
✱42 DIAL TONE PAUSE
0=5 seconds; 1=11 seconds; 2=30 seconds; Must be "0" for UL.
✱43 DIAL TONE DETECTION [1]
1=wait for true dial tone; 0=pause, then dial
✱44 RING DETECTION COUNT |
01-14; 15=answering machine; 00=no detection; Do not set to “00”
if voice module is used, or “01” if VIM is used.
✱45 PRIMARY FORMAT
0=Low Speed; 1=Contact ID; 2=Ademco High Speed; 3=Ademco
Express
✱46 LOW SPEED FORMAT (Primary)
0=Ademco Low Speed; 1=Sescoa/Radionics
✱47 SECONDARY FORMAT
0=Low Speed; 1=Contact ID; 2=Ademco High Speed; 3=Ademco
Express
✱48 LOW SPEED FORMAT (Sec.)
0=Ademco Low Speed; 1=Sescoa/Radionics
✱49 CHECKSUM VERIFICATION
1=yes; 0=no Prim Scndry
✱50 SESCOA/RADIONICS SELECT
1=Sescoa; 0=Radionics
✱51 DUAL REPORTING
1=yes; 0=no; If used with Spilt Reporting "1" option (1✱34), alarms
go to both primary & secondary numbers, while all other reports go
to secondary only. If used with Split Reporting "2" option,
open/close and test messages go to both lines, while all other
reports go to primary.
✱52 STANDARD/EXPANDED REPORT FOR PRIMARY
Alarm Rstr Bypass Trbl Opn/Cls Low Bat
0=standard; 1=expanded; Note: Expanded overrides 4+2 format.
✱53 STANDARD/EXPANDED REPORT FOR SECONDARY
Alarm Rstr Bypass Trbl Opn/Cls Low Bat
0=standard; 1=expanded; Note: Expanded overrides 4+2 format.
✱54-✱57, ✱59-✱62, ✱64-✱67, ✱69-✱72, ✱74-✱77
ALARM REPORT CODE & ID DIGITS FOR ZONES
Skip these fields. Use #93 Menu Mode, Zone Programming
to assign report codes.
SUPV. & RESTORE CODES
✱58 (zones 1-16) ✱63 (zones 17-32) ✱68 (zones 33-48) ✱73 (zones 49-64)
| Alrm Rst. | Alrm Rst. | Alrm Rst. | Alrm Rst.
| Trouble | Trouble | Trouble | Trouble
| Trble Rst. | Trble Rst. | Trble Rst. | Trble Rst.
| Bypass | Bypass | Bypass | Bypass
| Byps Rst. | Byps Rst. | Byps Rst. | Byps Rst.

Page 9
VISTA-40 TWO-PARTITION PROGRAMMING FORM
SUPV. & RESTORE CODES
✱78 (zones 87-99)
| Alrm Rst.
| Trouble
| Trble Rst.
| Bypass
| Bypass Rst.
ZONE TYPE RESTORE ENABLES 1=enable; 0=disable
✱79 FOR ZONE TYPES 1-8 ✱80 FOR TYPES 9–10
12345678 9 10
SYSTEM NON ALARM CODES
✱81 ✱82
First Digit Second Digit
Close | |
Open | |
Low Battery | |
Low Bat Res | |
AC Loss | |
AC Restore | |
Test | |
Power | |
Cancel | |
Prog. Tamp. | |
Second digit of each code
applies only to 4+2 or
expanded (fields ✱52 &
✱53) formats.
✱83 FIRST TEST REPORT TIME | | |
[Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 00-59;
00 in all boxes=instant (Day 01= Monday)
✱84 SWINGER SUPPRESSION Partition-Specific
✱85 ENABLE DIALER REPORTS Partition-Specific
FOR PANICS & DURESS
✱86 4208 MODULE ZONE ASSIGNMENT
1=allows 8 zone numbers (10-17) on one module, but prevents any
other polling loop expansion 0=Otherwise
✱87 ENTRY WARNING Partition-Specific
✱88 BURG. ALARM COMM. DELAY Partition-Specific
✱89 RESTORE REPORT TIMING
0=instant; 1=at bell timeout; 2=at disarm
✱90 2nd SUBS. ACCT # Partition-Specific
2nd Page Programming Fields (press ✱94)
1✱01 - 1✱09 ASSIGN RESPONSE TYPE FOR ZONES
Skip these fields. Use #93 Menu Mode, Zone
Programming to assign response types
MISCELLANEOUS WIRELESS OPTIONS
1✱28 RF TX LOW BATTERY SOUND
1=immediate; 0=when disarmed; Must be "1" for UL
1✱29 RF TX LOW BATTERY REPORT ENABLE
1=enable; 0=disable
Must be "1" for UL
1✱30 RF RCVR CHECK-IN INTERVAL [06] |
02-15 times 2 hours; 00 disables supervision
Max. "6" (12 hr) for UL
1✱31 RF TRANSMITTER CHECK-IN INTERVAL[12] |
02-15 times 2 hours; 00 disables transmitter supervision
Max. "6" (12 hr) for UL
1✱32 RF RECEIVER TYPE
1=4281; 2=5881; 0=NONE
1✱33 TOUCH-TONE W/ROTARY BACKUP ENABLE
1=enable; 0=disable
1✱34 COMM. SPLIT REPORT SELECTION
0=no; 1=alarms primary, others secondary;
2=open/close, test secondary, others primary; See ✱51 for
comments.
DIALER CODES ( Armed Stay, Time Set & Event Logging)
1✱40 1
✱41
First Digit Second Digit
Armed STAY | |
Time/Date set or event log reset | |
1✱43 PERM. KEYPAD BACKLIGHT Partition-Specific
1✱44 WIRELESS KEYPAD
TAMPER DETECT ENABLE 1=enable; 0=disable
1✱45 EXIT DELAY SOUNDING Partition-Specific
1✱46 AUXILIARY OUTPUT MODE
0=ground start; 1=open/close trigger; 2=keypad sounding
3=Non-Ademco AAV unit trigger
1✱47 CHIME ON EXT SIREN Partition-Specific
1✱48 WIRELESS KEYPAD ASSIGNMENT
0=disable; enter partition in which RF keypad used, 1-2.
1✱49 SUPPRESS TX SUPERVISION SOUND [1]
1=disable; 0=enable. Must be "0" for UL.
1✱52 SEND CANCEL IF ALARM + OFF Partition-Specific
1✱53 DOWNLOAD CALLBACK
1=callback not required; 0=callback required; Must be "0" for UL.
1✱57 ENABLE 5800 RF BUTTON GLOBAL ARM
Enter "1" to have the system arm/disarm following the button's
user's global arm settings. Enter "0" if the button is not to be used
to global arm the system.
1✱58 ENABLE 5800 RF BUTTON FORCE BYPASS
If zone is faulted after pressing button, keypad will beep once.
User should press button again within 4 sec. to force bypass
those zones. Enter 1 if force bypass is desired. Enter 0 if not
desired.
1✱60 AAV MODULE SELECT
Enter “1” only if AAV unit is used.
NOTE: If enabled zone 5 can no longer be used as a protection
zone.
1✱70 EVENT LOG TYPES
1=enable logging; 0=disable Alrm Chck Byps O/C Systm
1✱71 12/24 HOUR TIME STAMP FORMAT
0=12 hour; 1=24 hour
1✱74 RELAY TIMEOUT XX MINUTES | |
Enter the relay timeout, 0-127 in multiples of 2 minutes, desired
for #93 Menu Mode Relay Programming output command "56".
1✱75 RELAY TIMEOUT YY SECONDS | |
Enter the relay timeout, 0-127 seconds, desired for #93 Menu
Mode Relay Programming command "57".
1✱76 ACCESS CONTROL Partition-Specific

Page 10
VISTA-40 TWO-PARTITION PROGRAMMING FORM
3rd Page Programming Fields (press ✱94)
2✱00 NUMBER OF PARTITIONS [1]
Enter 2 for two partition systems.
2✱01 DAYLIGHT SAVINGS TIME | |
START/END MONTH Start End
00-12; if no daylight savings time, enter 00,00; default=04,10]
2✱02 DAYLIGHT SAVINGS TIME |
START/END WEEKEND # Start | End
Enter 1-7. 1=first; 2=second; 3=third; 4=fourth; 5=last; 6=next to
last; 7=3rd from last [1,5; 1st Sunday in April, last in Oct.]
2✱17 NUMBER OF CODES PER PARTITION 1 |
Enter 01-69. Total must be less than or equal to 70. 2 |
[Default=69 in part. 1; 01 in partition 2]
2✱18 ENABLE GOTO FOR THIS PARTITIONPartition-Specific
2✱19 USE PARTITION DESCRIPTORS
0=disable; 1=enable
2✱20 ENABLE J7 TRIGGERS BY PARTITIONPartition-Specific
2✱21 ENABLE SUPERVISION PULSES FOR LRR
TRIGGER OUTPUTS | |
Used for supervised connection to 7920SE. F B S
Enter 0 to disable or 1 to enable the listed outputs.
F= Fire; B= Burglary; S= Silent panic/duress

Page 11
VISTA-40 TWO-PARTITION PROGRAMMING FORM
PARTITION-SPECIFIC FIELDS
(PARTITION #1)
To program these fields,
1. Press
✱91 to select a partition.
2. Enter a partition-specific field number (ex. ✱09).
3. Repeat steps 1 & 2 for each partition in the system.
4. To return to the global program fields, enter a global field number.
PARTITION # 1 PROGRAM FIELDS
1st Page Fields
✱09 ENTRY DELAY #1 [02] |
(00-15 times 15 seconds)
✱10 EXIT DELAY #1 [03] |
(00-15 times 15 seconds)
✱11 ENTRY DELAY #2 [06] |
(00-15 times 15 seconds)
✱12 EXIT DELAY #2 [08] |
(00-15 times 15 seconds)
✱13 ALARM SOUNDER DURATION [04] |
01-15 times 2 minutes. Minimum 4 minutes for UL.
✱16 CONFIRMATION OF ARMING DING
1=enable; 0=disable
✱22 KEYPAD PANIC ENABLES [0-0-1]
1=enable; 0=disable 95 96 99
✱23 MULTIPLE ALARMS [1]
1=yes; 0=no
✱29 QUICK ARM [1]
1=yes; 0=no
✱32 PRIMARY SUBSCRIBER ACCT #
| | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
✱38 PREVENT ZONE XX BYPASS |
01-64; 00 if all zones (except Fire zones) can be bypassed
✱39 ENABLE OPEN/CLOSE REPORT
FOR INSTALLER CODE 1=enable; 0=disable
✱84 SWINGER SUPPRESSION [03] |
01-15 alarms; Must be "00" (disabled) for UL.
✱85 ENABLE DIALER REPORTS
FOR PANICS & DURESS 95 96 99 Duress
1=enable; 0=disable
✱87 ENTRY WARNING [1]
1=continuous; 0=3 beeps
✱88 BURG. ALARM COMM. DELAY
1=16 seconds; 0=no delay
✱90 SECONDARY SUBSCRIBER ACCT #
| | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
2nd Page Fields
1✱43 PERM. KEYPAD BACKLIGHT
1=enable; 0=disable; When disabled, display lights when any
key is pressed, and turns off after period of keypad inactivity.
1✱45 EXIT DELAY SOUNDING
1=enable; 0=disable; Produces quick beeping during exit delay if
enabled.
1✱47 CHIME ON EXT SIREN
1=enable; 0=disable
1✱52 SEND CANCEL IF ALARM + OFF
1=no restriction; 0=within Bell Timeout period only
1✱76 ACCESS CONTROL RELAY FOR PARTITION |
Enter relay number that will be pulsed for 2 seconds whenever
code + [0] is pressed. Enter 00-08 00=none
3rd Page Fields
2✱18 ENABLE GOTO FOR THIS PARTITION
1=enable; 0=disable
2✱20 ENABLE J7 TRIGGERS by PARTITION [1]
0=disable for displayed partition; 1=enable for displayed partition

Page 12
VISTA-40 TWO-PARTITION PROGRAMMING FORM
PARTITION-SPECIFIC FIELDS
(PARTITION #2)
To program these fields,
1. Press
✱91 to select a partition.
2. Enter a partition-specific field number (ex. ✱09).
3. Repeat steps 1 & 2 for each partition in the system.
4. To return to the global program fields, enter a global field number.
PARTITION # 2 PROGRAM FIELDS
1st Page Fields
✱09 ENTRY DELAY #1 [02] |
(00-15 times 15 seconds)
✱10 EXIT DELAY #1 [03] |
(00-15 times 15 seconds)
✱11 ENTRY DELAY #2 [06] |
(00-15 times 15 seconds)
✱12 EXIT DELAY #2 [08] |
(00-15 times 15 seconds)
✱13 ALARM SOUNDER DURATION [04] |
01-15 times 2 minutes. Minimum 4 minutes for UL.
✱16 CONFIRMATION OF ARMING DING
1=enable; 0=disable
✱22 KEYPAD PANIC ENABLES [0-0-1]
1=enable; 0=disable 95 96 99
✱23 MULTIPLE ALARMS [1]
1=yes; 0=no
✱29 QUICK ARM [1]
1=yes; 0=no
✱32 PRIMARY SUBSCRIBER ACCT #
| | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
✱38 PREVENT ZONE XX BYPASS |
01-64; 00 if all zones (except Fire zones) can be bypassed
✱39 ENABLE OPEN/CLOSE REPORT
FOR INSTALLER CODE 1=enable; 0=disable
✱84 SWINGER SUPPRESSION [03] |
01-15 alarms [15]; Must be "00" (disabled) for UL.
✱85 ENABLE DIALER REPORTS
FOR PANICS & DURESS 95 96 99 Duress
1=enable; 0=disable
✱87 ENTRY WARNING [1]
1=continuous; 0=3 beeps
✱88 BURG. ALARM COMM. DELAY
1=16 seconds; 0=no delay
✱90 SECONDARY SUBSCRIBER ACCT #
| | | |
Enter 00-09; B-F (11-15) [15 15 15 15]
2nd Page Fields
1✱43 PERM. KEYPAD BACKLIGHT
1=enable; 0=disable; When disabled, display lights when any
key is pressed, and turns off after period of keypad inactivity.
1✱45 EXIT DELAY SOUNDING
1=enable; 0=disable; Produces quick beeping during exit delay if
enabled.
1✱47 CHIME ON EXT SIREN
1=enable; 0=disable
1✱52 SEND CANCEL IF ALARM + OFF
1=no restriction; 0=within Bell Timeout period only
1✱76 ACCESS CONTROL RELAY FOR PARTITION |
Enter relay number that will be pulsed for 2 seconds whenever
code + [0] is pressed. Enter 00-08 00=none
3rd Page Fields
2✱18 ENABLE GOTO FOR THIS PARTITION
1=enable; 0=disable
2✱20 ENABLE J7 TRIGGERS by PARTITION [1]
0=disable for displayed partition; 1=enable for displayed partition

Page 13
PROGRAMMING WITH #93 MENU MODE
(Overview*)
NOTE: The following fields should be preset before beginning: 2✱00 Number of Partitions;
1✱32 Receiver Type. In addition, receivers should be programmed via Device
programming.
* Refer to the #93 Menu Mode section of the separate INSTALLATION INSTRUCTIONS document for detailed
programming procedures with this mode.
After programming all system related programming fields in the usual way, press #93 while still in programming
mode to display the first choice of the menu driven programming functions. Press 0 (NO) or 1 (YES) in response to
the displayed menu selection. Pressing 0 will display the next choice in sequence. Menu selections are as follows:
ZONE PROG?
0=No 1=Yes For programming the following:
• Zone Number
• Zone Response Type
• Hardwired zone
• Wireless Zone (type RF, UR or BR)
• Right/left Loop Zone
• Serial number RPM zone
• Partition Number for Zone
• Dialer report code for zone
SEQUENTIAL LEARN
0=no 1=yes For entering (enrolling) 5800 transmitter & serial number polling loop device serial numbers into
the system.
ALPHA PROG?
0=no 1=yes For entering alpha descriptors for the following:
• Zone Descriptors
• Installer's Message
• Custom Words
• Partition Descriptors
• Relay Descriptors
DEVICE PROG?
0=no 1=yes For defining the following device characteristics for addressable devices, including keypads, RF
receivers (4281/5881) and 4204 output relay modules:
• Device Address
• Device Type
• Device's Home Partition
• Keypad Options
• FA4285/4286Phone Module
RELAY PROG?
0=no 1=yes For defining output relay functions.
RLY VOICE DESCR?
0=no 1=yes For entering voice descriptors to be used with voice module functions.
CUSTOM INDEX #?
0=no 1=yes For creating custom word substitutes for voice module annunciation.
CLEAR RF SERTIAL#?
0=no 1=yes For deleting all RF serial numbers presently enrolled in the system.
#93 MENU MODE KEY COMMANDS
The following is a list of commands used while in the menu mode.
#93 Enters Menu mode
[✱] Serves as ENTER key. Press to have keypad accept entry.
[#] Backs up to previous screen.
0 Press to answer NO
1 Press to answer YES
01-99 All data entries are 2-digit entries.
00 Escapes from menu mode, back into field programming mode.

Page 14
CHANGING ZONE RESPONSE TYPE AND
REPORT CODE DATA FIELDS (Expert Mode)
• Because the VISTA-40 supports various types of input devices (such as button type transmitters, serial
number polling loop devices, etc.), zone characteristics, including zone response types and report codes,
must be initially programmed using #93 Menu Mode. However, once a zone has been programmed,
changes in response type or report code can be made using the respective data fields. This section lists
these fields.
• Zone Response Type and Report Code fields will automatically appear during normal programming, but
must be skipped if the zone has not been previously programmed. These fields include:
✱02 - ✱05 and 1✱01 - 1✱09 ASSIGN RESPONSE TYPES
✱54 - ✱78 REPORT CODES
To program these fields:
1. Enter Program Mode (enter installer code + [8] + [0] + [0]).
2. Press [✱] followed by the data field you wish to program.
3. Refer to the following list of fields when programming Zone Response Types and/or Report Codes.
4. Press ✱99 to exit program mode when programming is complete.
ZONE RESPONSE TYPE FIELDS
Response Types:
00 = Disabled zone
01 = Entry/Exit #1
02 = Entry/Exit #2
03 = Perimeter
04 = Interior Follower
05 = Day/Night
06 = 24 hour Silent Alarm
07 = 24 hour Audible Alarm
08 = 24 hour Auxiliary
09 = Fire
10 = Interior, Delay
20 = Arm stay
21 = Arm away
22 = Disarm
23= No alarm response
Notes:
Use of 1 or 2 RF RCVRs requires enabling their
respective faults (88-91) as troubles (type 5).
Enter 00 if no annunciation is desired.
88 & 90 = RCVR not receiving transmitter signals.
89 & 91 = RCVR not responding, bad conn. to panel.
87 = voice module supervision (type 05)
98 = Bell supervision (type 05)
✱02 - ✱05 ASSIGN RESPONSE TYPE FOR ZONES 1-27
(Enter 00-10; see Response Types below) see fields 1✱01-1✱09 to program
response types for zones 28-87.
✱02 ✱03 ✱04 ✱05
1 | [9] 9 | 17 | 25 |
2 | [3] 10 | 18 | 26 |
3 | [3] 11 | 19 | 27 |
4 | [3] 12 | 20 | 0|0
5 | [3] 13 | 21 | 97 | poll loop short
6 | [3] 14 | 22 | 95 | (1+✱or A panic)
7 | [3] 15 | 23 | 96 | (3+ # or C panic)
8 | [3] 16 | 24 | 99 | (✱ + # or B panic)
ASSIGN RESPONSE TYPE FOR ZONES
(Enter 00-10; see Response Types below)
1✱01 1✱02 1✱03 1✱04 1✱05
28 | 33 | 41 | 49 | 57 |
29 | 34 | 42 | 50 | 58 |
30 | 35 | 43 | 51 | 59 |
31 | 36 | 44 | 52 | 60 |
32 | 37 | 45 | 53 | 61 |
38 | 46 | 54 | 62 |
39 | 47 | 55 | 63 |
40 | 48 | 56 | 64 |
1✱09
87 | Voice Module
88 | 2nd RCVR
89 | 2nd RCVR
90 | 1st RCVR
91 | 1st RCVR
0|0
98 | Bell Supervision

Page 15
CHANGING ZONE RESPONSE TYPE AND
REPORT CODE DATA FIELDS
REPORT CODE FIELDS
ALARM REPORT CODE & ID DIGITS FOR ZONES 1-32 &
SUPV. & RESTORE CODES [All codes default to 00]
✱54 CODE ✱55 ID ✱56 CODE ✱57 ID ✱58
1 | | 9 | | | Alarm Rst.
2 | | 10 | | | Trouble
3 | | 11 | | | Trble Rst.
4 | | 12 | | | Bypass
5 | | 13 | | | Bypss
Rst.
6 | | 14 | |
7 | | 15 | |
8 | | 16 | |
✱59 CODE ✱60 ID ✱61 CODE ✱62 ID ✱63
17 | | 25 | | | Alarm Rst.
18 | | 26 | | | Trouble
19 | | 27 | | | Trble Rst.
20 | | 28 | | | Bypass
21 | | 29 | | | Bypss
Rst.
22 | | 30 | |
23 | | 31 | |
24 | | 32 | |
ALARM REPORT CODE & ID DIGITS FOR ZONES 33-64 &
SUPV. & RESTORE CODES [All codes default to 00]
✱64 CODE ✱65 ID ✱66 CODE ✱67 ID ✱68
33 | | 41 | | | Alarm Rst.
34 | | 42 | | | Trouble
35 | | 43 | | | Trble Rst.
36 | | 44 | | | Bypass
37 | | 45 | | | Bypss
Rst.
38 | | 46 | |
39 | | 47 | |
40 | | 48 | |
✱69 CODE ✱70 ID ✱71 CODE ✱72 ID ✱73
49 | | 57 | | | Alarm Rst.
50 | | 58 | | | Trouble
51 | | 59 | | | Trble Rst.
52 | | 60 | | | Bypass
53 | | 61 | | | Bypss
Rst.
54 | | 62 | |
55 | | 63 | |
56 | | 64 | |
ALARM REPORT CODE & ID DIGITS FOR ZONES 81-87, RF
RCVRs & PANICS, & THEIR SUPV. & RESTORE CODES
[All codes default to 00]
✱74 CODE ✱75 ID ✱76 CODE ✱77 ID
87 | | 89 | |
88 | | 90 | |
91 | |
| | Duress
98 | | Bell Supervision
97 | | Poll loop short
95 | | (panic key 1+✱)
96 | | ( panic key 3+#)
99 | | ( panic key ✱+ #)
✱78
| Alarm Rst.
| Trouble
| Trble Rst.
| Bypass
| Bypass Rst.
NOTES: 97= Poll Loop Short; 88 & 90 = RCVR not
receiving transmitter signals.
89 & 91 = RCVR not responding, bad conn. to
panel. 87 = 4285 phone module supervision
98 = Bell supervision

Page 16
SYSTEM LAYOUT WORKSHEETS
As with any security system, you should first define the installation. This includes determining how many partitions
will be used, how many zones per partition, and how many users per partition. You will also need to determine what
peripheral devices will be needed, and basic system options such as exit/entry delays, etc. The control panel itself
should be located in an area that will facilitate wire runs to all partitions, and will allow access to power and
telephone circuits.
To help you layout a partitioned system, use the following worksheet. This will further
simplify the programming process.
PARTITIONS
# of Users Descriptor Prim. Sec. Alpha Default Message
Partition # (69 max.*) (4 char max) Sub. # Sub. # (32 character maximum)
Partition 1
Partition 2
Keyswitch Arming Partition Assignment (1-2):
Wireless Keypad Partition Assignment (1-2):
Use Partition Descriptor (yes/no)?
* At least one user is assigned per partition, regardless of whether or not that partition is actually used. A maximum
of 70 user codes can be programmed in the system.
COMMUNICATION OPTIONS BY PARTITION (enter yes/no)
Option part 1 part. 2
Swinger Suppression Count 00-15; 00=no suppression
Cancel Report After Disarm
Dialer Reports for Panic (A or ✱+ 1)
Dialer Reports for Panic (C or # + 3)
Dialer Reports for Panic (B or ✱+ #)
Dialer Reports for Duress
Burglary Alarm Communications Delay (16 sec.)
SYSTEM DEFINITIONS BY PARTITION (enter values or yes/no)
Option part 1 part. 2
Entry Delay #1 (15-225 seconds):
Exit Delay #1 (15-225 seconds):
Entry Delay #2 (15-225 seconds):
Exit Delay #2 (15-225 seconds):
Quick Arming
Multiple Alarms per Arming
Keypad Panic for zone 95 (A or ✱+ 1)
Keypad Panic for zone 96 (C or # + 3)
Keypad Panic for zone 99 (B or ✱+ #)
Allow Sign-on (GOTO function)
Non-Bypassable Zone (can be any zone 1-64)
Sounder Timeout Duration (2 min. increments)
Keypad Annunciation During Entry**
Keypad Annunciation During Exit
Confirmation of Arming (ding)
Chime on External Siren
Access Control Relay (field 1✱76)
**no= 3 beeps yes=continuous

Page 17
DEVICES (Keypads, 4204, etc.)
ADDRESSABLE DEVICE OPTIONS
Device Type Home Sounder†
Address Partition Option
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
† Device type 1, and 2 only.
Keypad Sounder Options:
00 = no suppression
01 = suppress arm/disarm and entry/exit beeps
02 = suppress chime mode beeps only
03 = suppress arm/disarm, entry/exit, chime mode beeps
Device 0 = device not used, 1 = alpha keypad,
Type: 2 = fixed-word keypad, 3 = RF receiver,
4 = Output Relay module, 5 = 4285 phone
module
ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 1-2
4-digit RF Partition 1 Partition 2
Security Key? 2-digit Global Auth. Open/ 2-digit Global Auth. Open/ NOTES
Code Y/N User # Arm? Level Close User # Arm? level Close
Authority Levels: 1=master (arm, disarm, bypass, and/or modify lower level users)
2=manager (arm, disarm, bypass, and/or modify lower level users)
3=operator A (arm, disarm, bypass)
4=operator B (arm, disarm)
5=operator C (arm, disarm only if system was armed with this code)
6=duress code (arm, disarm, triggers silent panic alarm)

Page 18
ZONE DEFINITIONS FOR ZONES 1–24
DIP DIP † Enter loop number on module
Parti- RF Trans. Type †Ser. RPM RPM Hard Loop number must be “1” for hardwire and DIP devices)
Zone Zone tion RF UR BR RPM†left lp rght lp Wired Report Zone Information (part numbers) &
No. Type (1-2) typ 3 typ 4 typ 5 typ 6 typ 7 typ 8 typ 1 Code Alpha Descriptor (3 words max.)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Page 19
ZONE DEFINITIONS FOR ZONES 25–48
DIP DIP † Enter loop number on module
Parti- RF Trans. Type†Ser. RPM RPM Hard Loop number must be “1” for hardwire and DIP devices)
Zone Zone tion RF UR BR RPM†left lp rght lp Wired Report Zone Information (part numbers) &
No. Type (1-2) typ 3 typ 4 typ 5 typ 6 typ 7 typ 8 typ 1 Code Alpha Descriptor (3 words max.)
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

Page 20
ZONE DEFINITIONS FOR ZONES 49–64
DIP DIP † Enter loop number on module
Parti- RF Trans. Type†Ser. RPM RPM Hard Loop number must be 1 for hardwire and DIP devices)
Zone Zone tion RF UR BR RPM†left lp rght lp Wired Report Zone Information (part numbers) &
No. Type (1-2) typ 3 typ 4 typ 5 typ 6 typ 7 typ 8 typ 1 Code Alpha Descriptor (3 words max.)
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Zone Types: 00=zone not used 05=day/night burglary 10=interior (delay)
01=entry/exit 1 06=24 hour silent 20=arm stay
02=entry/exit 2 07=24 hour audible 21=arm away
03=perimeter 08=24 hour auxiliary 22=disarm
04=interior (follower) 09=supervised fire 23=no alarm response
REPORTS TO CENTRAL STATION
Option No (✔) Yes (✔)
Armed Stay
Time/Date Reset
EVENT LOG TYPES
Option No (✔) Yes (✔)
Alarm
Trouble
Bypass
Open/Close
System