ADLINK Technology NuPRO-861 User manual

Recycled Paper
NuPRO-861
Full-Size SBC
User’s Manual

©Copyright 2004 ADLINK Technology Inc.
All Rights Reserved.
Manual Rev. 1.00: July 14, 2004
The information in this document is subject to change without prior notice in
order to improve reliability, design, and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Trademarks
NuDAQ®, NuIPC®, NuDAM®, NuPRO®are registered trademarks of ADLINK
Technology Inc. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.

Getting Service from ADLINK
Customer Satisfaction is top priority for ADLINK Technology Inc. If you need
any help or service, please contact us.
ADLINK TECHNOLOGY INC.
Web Site http://www.adlinktech.com
Sales & Service [email protected]
TEL [phone] FAX [phone]
Address 9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan
Please email or FAX your detailed information for prompt, satisfactory, and
consistent service.
Detailed Company Information
Company/Organization
Contact Person
E-mail Address
Address
Country
TEL FAX
Web Site
Questions
Product Model
Environment
OS:
Computer Brand:
M/B: CPU:
Chipset: BIOS:
Video Card:
NIC:
Other:
Detail Description
Suggestions for ADLINK

Table of Contents •i
Table of Contents
Chapter 1 Introduction..................................................................1
1.1 Unpacking Checklist........................................................................ 2
1.2 Features.......................................................................................... 4
1.3 Functional Block.............................................................................. 6
1.4 Specifications.................................................................................. 7
Chapter 2 Installation....................................................................9
2.1 System Installation.......................................................................... 9
2.2 Board Layout................................................................................. 13
2.3 Jumper setting............................................................................... 14
2.4 Connectors Description................................................................. 16
2.5 Optional IP-ALCS20 Audio Card................................................... 30
Chapter 3 Award BIOS Setup.....................................................33
3.1 BIOS Instructions.......................................................................... 33
3.2 Main Menu .................................................................................... 33
3.3 Standard CMOS Features............................................................. 35
3.4 IDE Adaptors................................................................................. 37
3.5 Advanced BIOS Features.............................................................. 38
3.6 Advanced Chipset Features.......................................................... 42
3.7 Integrated Peripherals................................................................... 45
3.8 Power Management Setup............................................................ 50
3.9 Plug and Play / PCI Configurations............................................... 54
3.10 PC Health Status........................................................................... 55
3.11 Frequency/Voltage Control............................................................ 56
3.12 Load Fail-Safe Defaults................................................................. 57
3.13 Load Optimized Defaults............................................................... 57
3.14 Supervisor/User Password Setting................................................ 57
3.15 Exit Selecting ................................................................................ 58
Warranty Policy ...........................................................................61

Introduction •1
1
Introduction
The NuPRO-861 series combines the high performance and exceptional value
of the Intel®855GME chipset with a full-featured, new generation, industrial
SBC. The Intel®advanced 855GME chipset support socket 478-pins Intel®
Pentium®M processor of 1.30GHz and up to 1.80GHz, that memory base on
the FSB 400/533MHz operation supports DDR SDRAM interface. In the
meantime, the 855GME chipset integrated the LVDS, DVI & VGA function. The
NuPRO-861 system memory size can be up to 2GB DDR memory, onboard
Intel®82541 Gigabit Ethernet controller (supporting 10/100/1000 Base-TX
Ethernet), optional Audio card and with 2 COM ports, besides the NuPRO-861
with 4 internal USB2.0 ports and a VGA, CompactFlash™ type II connector.
They are for ATM, CTI and high-end applications.
The 82801DB I/O Controller Hub (ICH4) employs the Intel®Accelerated Hub
Architecture to make a direct connection from the graphics and memory to the
integrated Ethernet controller, the IDE controllers (ATA/33 or ATA/66 or
ATA/100), four USB ports that are supported USB 1.1/2.0 standard meets the
performance, stability and reliability requirements.
The industrial SBC - NuPRO-861 is suitable and valuable for all the industry
applications, which also well support with the Windows®98 / 2000 / XP / NT
and Linux®operation system.

2•Introduction
1.1 Unpacking Checklist
1. Take out the NuPRO-861 series unit from the carton box, check if the unit is
properly secure in the plastic bag.
2. Check the contents of the carton box:
¡Industrial board ¡Installation guide
¡ATA-66/100 HDD ribbon cable ¡Floppy ribbon cable
¡Print & COM1 ribbon cable ¡USB cable (1 Set)
(for USB2.0)
¡COM2 ribbon cable ¡KB & MS Y type cable

Introduction •3
¡VGA round cable ¡ATX control round cable
(4-pins to 4-pins)
¡KB extend to BP round cable ¡Driver CD
(5-pins to 6-pins)
¡Low profile heat sink with fan
Note: The package of the NuPRO-861 OEM version non-standard
configuration may vary in function or contents according to
different configuration requests
CAUTION: This board must be protected from static discharge and
physical shock. Never remove any of the socketed parts except
at a static-free workstation. Use the anti-static bag shipped with
the product to handle the board. Wear a wrist strap grounded
through one of the system's ESD Ground jacks while servicing
system components.
!

4•Introduction
1.2 Features
Graphic and Ethernet
The NuPRO-861 is base on the Intel®855GME chipset, offers users integrated
LVDS, graphic, and gigabit Ethernet.
•Enhanced integrated LVDS & graphics:
400 / 533 MHz FSB support
LVDS resolution up to 1600 x 1200 UXGA
Onboard LVDS, DVI interface & CRT VGA connector
•Built-in Gigabit Ethernet:
Onboard Intel®Gigabit Ethernet controller
Support 10 / 100 / 1000 Base-TX Ethernet
•Memory:
DDR-SDRAM 266 / 333
2 x 184-pins DIMM socket, with support ECC
Up to 2.0GB memory (max.)
•I/O Connectivity - ICH4:
Four Hi-Speed USB2.0 ports
Onboard AC97 Audio pin header (IP-ALCS20 Audio card by option)
Ultra ATA/66/100
The ICH4 provides two channel Ultra ATA/66/100 Bus Master IDE controller,
that support Ultra ATA/66/100 protocols - perfect for demanding applications
such as real-time video, multimedia, and high performance operating system.
A new IDE cable is required for Ultra ATA/66/100. This cable is an
80-conductor cable; however the connectors are backwards compatible with
ATA/33.
Hardware Monitoring
Hardware monitoring allows the user to monitor various aspects of their
systems operations and status. The features include CPU temperature,
voltage and RPM of fan. Moreover, the NuPRO-861 with jumper can adjust the
fan speed.

Introduction •5
I/O Shield Connector
The SBC is equipped with an I/O bracket. Please use the appropriate I/O
shield.
Figure 1: I/O back panel layout
NuPRO-861 Series Overview
Function NuPRO-861
¡Chipset Intel®855GME
¡LVDS function 
¡DVI function 
¡VGA function 
¡Gigabit Ethernet function 
¡40-pins EIDE interface 2
¡Type II CF socket 1
¡Parallel port 1
¡Serial ports 2
¡USB 2.0 ports (by USB cable) 4
¡Fan connector 2

6•Introduction
1.3 Functional Block
The following topics provide an overview of the NuPRO-861 main features as
shown in the functional block diagram below and also the main board.
Functional Block Diagram
Socket 478-pins
for
Intel PentiumM ClockVRM
DATACTRLADDR
GMCH (855GME)
732 Micro FCBGA
ICH4
421 BGA
DDR266/333 X2
DVI / CRT
Device
Super I/O
W83627HF
ATA100
USB2.0
IDE Primary
IDE Secondary
USB Port 1/2
USB Port 3/4
FWH
Keyboard
Mouse
COM Port
LPT Port
Floppy
PCI BUS
PICMG SLOT
LVDS
or
VGA
400/533 MHz FSB
Intel
82541
10/100/1000
Base-TX
CF Socket
ISABridge
IT8888
ISABUS
Figure 2: Functional Block Diagram

Introduction •7
1.4 Specifications
•Processor:
•Intel®Pentium®M processor with socket 478-pins package
•Processor operating at 1.3GHz and up to 1.8GHz
System bus frequency at 400/533MHz FSB
•Chipset:
Intel®855GME + ICH4 AGPset
•DRAM Module:
•2 x 184-pins DIMM socket
•For DDR 266 / 333 memory
Support DDR SDRAM up to 2GB (max.)
•LVDS / DVI & VGA:
•Intel®855GME Chipset integrated LVDS & Graphic controller
•Onboard one DVI & 16-pins CRT VGA connectors
•Gigabit Ethernet:
•Intel®82541 Ethernet controller
For 10 / 100 / 1000 Base-TX Ethernet
Onboard one RJ-45 Ethernet connector
•External Connector:
•1 x type II CompactFlash™ connector
•(If user uses the CF card, it will occupy the IDE2 master.)
•1 x 5-pins extend to Backplane for external KB connector
•Onboard I/O:
On-Chip I/O integrated with Keyboard, Mouse, Parallel and Serial,
Fast IR and Power-ON controller
•Onboard PCI / IDE:
Intel®ICH4 south bridge controller
PCI rev2.2 Compliant
ACPI Compliant Power Management
PCI Bus IDE Port with PIO / Ultra DMA-100 x 2 (Up to four Devices)
•Rear I/O Connectors:
•RJ-45 Ethernet connector
•D-Sub DVI connector
•PS/2 Mouse and PS/2 style Keyboard
•Internal I/O Connectors (pin-header):

8•Introduction
•1 x 16-pins CRT VGA port
•2 x Serial ports for RS-232
•4 x USB2.0 connectors (USB cable with bracket)
•BIOS:
Award Plug and Play BIOS
•Form Factor:
13.3” x 4.8” (338 x 122mm)
•Weight:
0.84lb (380g)

Installation •9
2
Installation
2.1 System Installation
CPU Installation
Carefully follow the steps below to install the CPU:
1. Check and confirm that the jumpers are correctly set for the CPU being
installed (figure 3).
2. Lift the releasing lever of the Socket 478.
3. Align the pins of the CPU with the pinholes of the Socket 478. Be sure to pay
attention to the orientation of the CPU.
Figure 3: CPU Socket
4. Push down the CPU into the Socket 478.
5. Push down the release lever and lock it against the key hook.
6. Hook the hole in ZIF clip for the CPU cooling fan onto the notch on the socket
478.
7. Place the CPU cooling fan on top of the CPU surface.

10 •Installation
8. Push down the opposite side of the ZIF clip and hook it.
9. Slide the head of the clip to left and lock it.
10. Connect the cooling fan cable to the socket as shown below. Be careful not
to place the cable on the CPU cooling fan.
Removing a CPU:
1. Before removing the CPU, turn off the NuPRO-861 Series power; then wait
for about 20 minutes until the heat radiation plate of the cooling fan and the
CPU cools down.
2. To remove the CPU, lift the releasing lever of the Socket 478.
CAUTION: The CPU and the heat radiation plate are hot. They may cause
burns.
To remove the CPU, reverse the installation steps.
Heat Sink & Retention Module Installation
Make sure there is good contact between the processors and the heat sinks & fan.
Insufficient contact, incorrect types of heat sinks, fans, thermal compound used,
or improper amount of thermal compound applied on the CPU die can cause the
processors to overheat, which may cause the system to crash.
Figure 4: Heat Sink & Retention Module Installation

Installation •11
Memory Module Installation
Figure 5 illustrates the notch marks and what they should look like on the DIMM
memory module.
DIMMs have 184-pins and two notches matching the onboard DIMM socket.
DIMM modules are installed by placing the chip firmly into the socket at a
90-degree angle and pressing straight down (figure 6) until it fits tightly into the
DIMM socket.
Figure 5: DIMM Memory and 184-pins Socket
Figure 6: Memory Installation
Carefully follow the steps below to install the DIMMs:
1. To avoid generating static electricity and damaging the DIMM, ground
yourself by touching a grounded metal surface or using a ground scrap
before touching the DIMM.
2. Do not touch the connector of the DIMM. Dirt residues may cause
malfunctions.
3. Hold the DIMM with its notch to the front side of the NuPRO-861 Series and
insert it completely into the socket. A DIMM should be inserted into the inner
socket first. Guide the hole on each end of the DIMM over the retaining post
at each end of the DIMM socket.
4. If installing two DIMMs, install the second DIMM using the same procedure
as above.
5. Do not forcefully insert the DIMM if it does not go in smoothly. Remove the
DIMM completely and try again.

12 •Installation
6. Make sure the DIMM is properly installed and locked by the tabs on both
sides of the socket.
Removing a DIMM:
To remove the DIMM, use fingers or a small screwdriver to carefully push away
the plastic tabs that secure the DIMM at each end. Lift it out of the socket.
Make sure the DIMM is stored in an anti-static bag which must be of
the same size and manufacture of memory modules.
Setting Jumpers and DIP Switches
There are jumpers and DIP-switches on the Embedded Board of the NuPRO-861
Series. You can set the jumpers to make the necessary operations.
Figure 7: Jumper Connector
For three-pin jumpers (Figure 7), the jumper setting is 1-2 when the jumper
connects pins 1 and 2. The setting is 2-3 when pins 2 and 3 are connected and so
on. The pins are numbered “1“ and “3“ on the circuit board for identification
purposes. Also, pin 1 has a thick line surrounding the jumper.
To move a jumper from one position to another, use needle-nose pliers or
tweezers to pull the pin cap off the pins and move to the required position.

Installation •13
2.2 Board Layout
CN3
CN4 CN10 CN12
CN13
CN14
LVDS
CF
CN16 JP3
JP1
CN8
CN9
USB2/3
USB0/1
CN1CN5
CN2
CN6
CN19
CN17
CN18
CN20
CN15
CN11CN7
JP2
Figure 8: Jumper and Connector Locations

14 •Installation
2.3 Jumper setting
Jumper Location Description:
Use the information in the following table to change the jumpers and the DIP
switches.
Jumpers Functions
JP1 Clear CMOS Setting Select
JP2 CPU Type Setting Select
JP3 Watchdog Timer Setting Select
A description on setting the jumpers to enable/disable or change functions To set
up the correct configuration is . All jumpers’ location please refer to jumper
location diagram.
1. Clear CMOS Setting Select: JP1
Function JP1
Normal (Default) 1-2
Clear CMOS 2-3
Location
2. CPU Type Setting Select: JP2
Function JP2
CPU FSB 400 MHz (Default) 1-2 On
CPU FSB 533 MHz 1-2 Off
Location