ADT 2 Gig Go! Control User manual

2 Gig Go! Control Quick Guide
http://alpha.adt.com/help/280[11/14/2018 8:14:39 PM]
2 Gig Go! Control - Quick Guide
For a detailed review of the entire system, please view the 2 Gig Go!Control manual.
« Help Center
Arm &
Disarm
Battery Bypass
Protected
Areas
Date &
Time
Settings
Chimes &
Beeps
Reset Security
Codes
Trouble
Conditions
Volume
Arm and Disarm
Arm:
To arm all sensors in STAY or AWAY mode:
At the Home screen, press [Security > Arm].
Enter your [security code].
Press the [STAY] or [AWAY] button.
Disarm:
Select

2 Gig Go! Control Quick Guide
http://alpha.adt.com/help/280[11/14/2018 8:14:39 PM]
To disarm, press [DISARM] on the Security Screen or the Menu Sreen, and enter a valid [security
code].
For more information on this topic please visit the complete 2 Gig Go!Control manual.
Battery
The 2 Gig Go! Control operates on a 7.2V battery.
For instructions on replacing your battery, please visit our Battery Replacement Page.
Bypass Protected Areas
Bypassing a zone allows you to arm your system with certain protected areas intentionally unarmed or to
access a protected area when the system is armed.
Press [ARM] from the Security or Menu Screen.
Press [BYPASS ALL] to force bypass the open sensors (including any open interior sensors).
Enter your [security code] (unless the installer has set Quick Bypass) to activate the bypass and
continue to the Arming Screen.
For more information on this topic please visit the complete 2 Gig Go!Control manual.
Change Date and Time
To access date and time settings:
From the Home Screen, press [SECURITY].
From the Security Screen, press [MENU].
From the Menu Screen, press [TOOLBOX].
From the second Toolbox Screen (2 of 3), press [SET DATE or SET TIME].
Use up and down arrows to set the current date or time. Press [OK].
A confirmation screen showing the date and time set appears. Press [OK].
For more information on this topic please visit the complete 2 Gig Go!Control manual.
Chimes and Beeps
Your system communicates events using chimes and beeps whenever a protected door or window is
opened.
To silence or enable chimes, select the [STATUS & SETTINGS] button from the home screen.
Scroll down until you reach the [Chime] button.
Touching the button toggles between Chime On and Chime Off.

2 Gig Go! Control Quick Guide
http://alpha.adt.com/help/280[11/14/2018 8:14:39 PM]
Select the [CLOSE] button to exit through the menus back to the home screen.
For more information on this topic please visit the complete 2 Gig Go!Control manual.
Reset
It is recommended that you clear the system status after an alarm event.
To reset your panel, arm the panel or, after disarming, press [CLEAR ALARM HISTORY] on the Alarm
Memory screen.
For more information on this topic please visit the complete 2 Gig Go!Control manual.
Security Codes
To set-up the user codes:
At the Home screen, press [SECURITY].
At the Security screen, press [MENU].
At the Menu screen, press [TOOLBOX].
Enter the [Master Code] to access the Toolbox.
On the Toolbox (1 of 3) screen, press [USER MANAGEMENT].
Press one of the [ADD USER] buttons.
Enter a unique four (4) digit code for the new user code. Then press [OK].
Enter the code again to confirm it. Then press [OK].
At the Confirmation screen, press [OK] to return to the User Management screen.
For more information on this topic please visit the complete 2 Gig Go!Control manual.
Trouble Conditions
Your security system is able to automatically test itself for power failures, low batteries, nonworking
sensors, and communication troubles with the central monitoring station. When a trouble condition is
detected, the trouble indicator will turn on and the keypad will beep every 10 seconds. Press the [TROUBLE
ALERT ICON] to view the trouble condition. Use the up and down arrows to scroll through the trouble conditions.
After viewing the trouble events, press [OK] to acknowledge the trouble condition and silence
the trouble beeps.
For more information on this topic please visit the 2 Gig Go! Troubleshooting page.
Volume

2 Gig Go! Control Quick Guide
http://alpha.adt.com/help/280[11/14/2018 8:14:39 PM]
Return to Top
To set the volume:
At the Home screen, press [SECURITY].
At the Security screen, press [MENU].
At the Menu screen, press [TOOLBOX].
Enter the [Master Code] to gain access to the Toolbox.
At the Toolbox (1 of 3) screen, press [BRIGHTNESS/VOLUME]. You can set the brightness using the
top bar. Adjust the level from 1 to 12 using the buttons on each end of the bar.
You can set the speaker volume for the chimes and announcements on the bottom bar. Adjust the
level from 1 to 12 using the buttons on each end of the bar.
When you are finished, press [OK].
For more information on this topic please visit the complete 2 Gig Go!Control manual.
How can we help?
Search