ADT Safe-N-Go User manual

Quick Start Guide
ADT Safe-N-Go

Getting to know your device
SOS button
Silent mode button
LED light
Speaker
Microphone
Manual test button
Lanyard hole

Charging contacts
Charging contacts
LED light
Screw holes

Charging your device
The charging base light will glow when charging and turn solid when
fully charged.
Charging base
• Place the device on the charging base.
• Connect the USB cable from charging base to the AC adaptor.
For the first time use, please fully charge the battery for around 2-3
hours.
When the battery level falls below 20%, the device will give a voice
prompt of “low battery alarm”.
Tip
Tip

Switching the device ON/OFF
• To turn on the device: press the CALL button for 1 second, all
the LEDs will flash rapidly. The device can also be turned on
automatically by charging via magnetic USB cable or put it into
the docking station.
• To turn off the device: press and hold the side button and SOS
button together for 3 seconds until the LEDs turn off.

What do the lights mean?
Cellular signal indicator - Green
Positioning indicator - Blue
Power indicator - Red
Green Light shows a single ash
rapidly every 3 seconds
Light shows a double ash
rapidly every 3 seconds
Means The device has a stable
Cellular signal
The device is registered to
the Cellular network
Blue
Light shows
a single ash
rapidly every 3
seconds
Light shows a
double ash rapidly
every 3 seconds
Light Off
Means
The device
has no latest
location x
The device has
latest location x
The device is
not xing the
latest location
Red Red Blinking Quickly Red Off or blinking slowly
Means Battery power is lower than
20% The device is charging
Red Red ON (solid) Red shows a double ash
rapidly every 3 seconds
State Device has been fully
charged Bluetooth Low Energy

Activating an SOS alarm
Activate SOS on docking station
Press twice
Voice prompt or
Vibration indicating
SOS alert activation
When you need help, press the SOS button twice, you will hear a voice
prompt of activating an SOS alarm. Voice prompt will say “SOS alert
has been activated, click SOS to Stop”. This will prompt the Alarm
Response process. Only click SOS again in case of false alarm.
Note: Only works if ADT Safe-N-Go device is connected to the docking
station via Bluetooth and is in the proximity of 10-15 metres.
Charging contacts
LED light
SOS button

Silent Mode Button
• Double-click this button to turn off voice warnings, double-click the
button again to turn on voice warnings.
• Put device on charging base more than 30 seconds, and they will
be paired automatically via Bluetooth.
De-Activating an SOS alarm
In the case of a false alarm, press SOS button once after, you hear
a voice prompt of activating an SOS alarm. Voice prompt will say
“SOS alert has been activated, click SOS to Stop”. Only click SOS
again in case of false alarm. Voice prompt will say “Alarm has been
cancelled” to confirm.

Specifications
Cautions
• Dimension: 62mm*47mm*17mm
• Weight: 53g
• Battery: Rechargeable, 3.7V, l000mAh
• Charging voltage: 5V DC
• Waterproof: IP67
• 4 locating technologies: GPS, BLE, WIFI, LBS
Please comply with the instructions to extend the unit life:
• Don’t use & store the unit in dusty places.
• Don’t put the unit in overheated or over cooled places.
• Clean the unit with a piece of dry cloth. Don’t clean with chemicals
or detergent.
• Don’t disassemble or refit the unit.
• Using other batteries will cause an unwanted situation.
Warning: Keep the IMEI and SIM in confidential, or your privacy
may expose.

Notes

ADT Safe-N-Go
38 South St, Rydalmere NSW 2116
Phone: 131 238
www: www.adtsecurity.com.au