ADT Safewatch Pro 3000 User guide

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Safewatch Pro 3000 System Manual
« Help Center
System
Overview
System
Keywords
Arm &
Disarm the
System
Panic Alarms Trouble
Conditions
User Access
Codes
System
Testing
Other System
Information
System Overview
Overview
The Safewatch Pro 3000 represents the latest in home and business security protection technology
providing ADT customers with:
Burglary, emergency, and fire* protection
At least one touchpad to control operations and display system status
Sensors for perimeter and interior burglary protection
Smoke or combustion detectors* for early fire warning
Display of zones triggered during alarm
Select

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Multiple partition arming/disarming
Up to four programmable pagers
System scheduling
The Safetwatch Pro 3000 is designed to be as maintenance free as possible, however we suggest that you
still test your system once a month and after any alarm occurrences.
Treat the system as you would any other electrical equipment; do not slam protected doors or windows,
keep dust from accumulating on the touchpad and sensors, and do not spray water or any liquid on the
units.
*Your system may or may not be set up for fire protection.
System Keywords
Keyword Meaning
Alarm An alarm has been detected in the armed system. See zone area number(s) to identify
location of triggered alarm.
Away All burglary zones, interior and perimeter, are armed.
Instant Perimeter burglary zones are armed and entry delay is turned off.
Stay Perimeter burglary zones, such as protected windows and doors, are armed.
Fire Appears when a fire alarm or fire fault is present. Accompanied by a display of the zone
in alarm.
Bat Low battery condition in a wireless sensor if zone number is displayed or low system
battery if no zone number is displayed.
Chime Appears when the Chime feature is activated.
Bypass Arming the system with protected areas intentionally left open.
Check A malfunction has occurred. See area zone number to identify location of trouble event.
No AC AC power has been cut off and the system is running on backup battery.
Not Ready System not ready for arming. READY indicates the system is ready.
Arm & Disarm the System
When arming your system it is important to note that:
Before arming your system, all protected areas must be closed. Use the READY/[*] key to display
any faulted (i.e., open) zones. The system will display READY when the system is ready to be armed.
Codes and commands must be within of 10 seconds of each other. If more than 10 seconds elapse
between entries, the entry will be aborted and must be re-entered.

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
If you make a mistake while entering your security code, first stop and then press [*][*] to start
over.
There are four possible modes for arming your system:
1. Instant Mode arms the entire perimeter when no one is expected to use an entry/exit door. The
alarm will sound immediately if any protected zone is opened, including designated entry/exit doors. Exit
delay is not possible in instant mode. To activate, press your [security code] + [7].
2. Stay Mode arms the entire perimeter and an alarm will sound if any protected area or non-entry/exit if
opened. Stay mode triggers the exit delay; setting the stay mode does not arm the system immediately
but rather after a designated amount of time (referred to as the exit delay). To activate, enter [security
code] + [3]
3. Night-Stay Mode arms the entire perimeter in addition to pre-selected interior sensors. In this mode,
alarms will sound if interior zones are triggered (e.g., entering area in the middle of the night), though
entry/exit is possible through designated areas. To activate, enter [security code] + [3] + [3].
4. Away Mode arms the entire interior and exterior. As such, this mode is not ideal for those with
pets/children roaming in and out of interior zones. Away mode triggers the exit delay; setting the away
mode does not arm the system immediately but rather after a designated amount of time (referred to as
the exit delay). You may reenter through the designated entry/exit door without causing an alarm, but
you must disarm the system within the entry delay period. To activate, enter [security code] + [2].
Disarming
PLEASE NOTE: If your alarm is sounding upon return, DO NOT ENTER! CALL THE POLICE from a safe
location. If you return and find that the main sounder has shut itself off but the touchpad is beeping
rapidly, TAKE CAUTION Your alarm was activated while you were out.
Your security code + OFF is used to disarm the system, to silence the alarm and trouble sounds, and to
clear any alarm memories. The touchpad will emit a single tone to confirm that the system has been
disarmed and/or silenced.
To clear the memory of an alarm, press your security code + OFF key first, then enter your security code +
OFF again to clear.
Bypassing Protection Zones
Zones (also called partitions) are areas that can be bypassed when arming the system. This could be ideal
for those who want to arm all but one door/window.
Bypassing Protection Zones

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Bypassing zones allows you to arm your system with one or more zones intentionally unprotected. The
system must be disarmed before arming. Fire zones cannot be bypassed.
1. Enter your security number + 6 + two digit zone number (e.g., 06, 10, etc.).
2. Once all bypassed zones are displayed on the touchpad, continue to arm the system as usual.
Door Chime (Entry/Exit Beeps)
To turn the door chime function on or off, press and hold the Chime key for 2 seconds or enter [security
code] + [9].
Panic Alarms
Emergency Keys
Your system may have been programmed to use special keys to manually active emergency (panic)
functions. To active a panic function, press and hold down the designated lettered key for at least 2
seconds or press both keys of the designated key pair at the same time.
Function Signal to Customer Care Sound Activated
Silent Alarm Silent alarm No audible alarm to indicate
silent alarm has been activated
but message sent to Customer
Care
Audible Alarm Audible alarm A loud, steady alarm on touchpad
and any sounders
Personal Alarm Emergency alarm Steady alarm at touchpad
Fire Alarm Fire alarm Pulsing sound at external bells
and sirens
Trouble Conditions
Trouble conditions are indicated by the word CHECK and continual beeping from the touchpad. Any key
will silence the beeping. A display of CHECK + zone no. may indicate that a problem requires your
attention. Check the specified zone area, close any open doors or windows and enter your security code
and press [OFF]. If your system includes wireless sensors, the CHECK condition may be caused by some
change in the environment of the protected area.
To silence trouble beeps, press any key or enter your security code and press [OFF].
For a complete list of Trouble Conditions, please refer to the Safewatch and Ademco Systems

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Troubleshooting page.
User Access Codes
Access Code Programming
User Access Codes/Security Codes
Your system allows for up to 45 different security codes for use by other users, however only the Master
User or the Partition Programmer can assign user codes to users. User codes can be used
interchangeably while performing functions, e.g., a system can be armed with one user’s code and
disarmed by another’s, with the exception of the guest user code.
Programming User Codes and Authority Levels
1. Assign an authority level to that user:
1. Master: Can perform all system functions and assign codes in both partitions. Can change
their own code using: Master code + [8]+02+new code + new code again.
2. Standard User: Can perform security functions in assigned partition only.
3. Arm Only: Can only arm the system, cannot disarm or do other functions.
4. Guest: Typically assigned to a babysitter or a cleaner, a guest can arm the system in the
assigned partitions, but cannot disarm the system unless the system was armed with this
code.
5. Duress: Intended for use when forced to disarm or arm the system under threat. When used,
the system will act normally, but will silently notify the Customer Care Center of your situation,
if that service has been provided.
6. Partition Programmer: Can do everything a standard user can do, plus assign user codes to
users in their partition.
2. Assign other attributes as necessary.
User Code Attributes
Code/Level Command String Notes
Add A User Touchpad will
beep once to confirm.
Mast/Prog code + [8] + user
no. + new user’s code
User 01 = installer; User 02 = master;
User 03 = part. 1 programmer; User 33 =
partition 2 programmer
Delete User Code Mast/Prog code + [8] + [user
no.] + [#] [0]
The user code and all attributes
programmed for this user number
(except for the assigned partition),
including any associated RF keys, are
erased from the system.

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Authority Level Mast/Prog code + [8] + [user
no.] + [#][1] + authority level
0 = standard user; 1 = arm only; 2 =
guest; 3 = duress; 4= partition
programmer
Access Group Mast/Prog code + [8] + [user
no.] + [#][2] + group (1-8)
You can assign users to a group and
then set an access schedule that defines
the times this group can operate the
system. The system will ignore these
users outside of the scheduled times.
User’s Partition Partition 1 =
users 03-32 Partition 2 =
users 33-49
Master Code [8] + [user no.] +
[#][3]+ partition(s) + [#] (to
end)
Use this command to assign the
partitions a specific user can access.
Enter the numbers sequentially, then
end the entry with [#]. 0 = clears
partition 1 and partition 2 assignments; 1
= partition 1; 2 = partition 2; 3 = common
partitions
RF User Number Mast/Prog code + [8] + [user
no.] + [#][4] + zone number
Use this command to assign a wireless
button device (keyfob) to this user. For
the zone number, enter the number
assigned to a button on the keyfob that
will be used for arming/disarming by this
user.
Pager On/Off Mast/Prog code + [8] + [user
no.] + [#][5] + 0 or 1
Program a user to receive a message to
their pager whenever this code is used
to arm/disarm. 1 = allow paging; 0= no
paging for this user.
System Testing
Testing Your System
Testing allows for each protection point to be checked for proper operation. While the touchpad will beep
every 40 seconds during TEST mode, no alarm messages will be sent to the Customer Care Center. We
recommend testing the system once a month.
To test the system:
1. Disarm the system and close all protected areas. The READY light will appear.
2. Enter your [security code] + [5] then [0] (walk).
3. The external sounder should sound for 1 second. If it does not sound, call for service.
4. Go through each fault zone individually. Open each door/window and listen for three beeps from
the touchpad. The zone number or description should appear on the display and clear when the

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
door/window is closed.
5. Go through each interior zone individually. Walk in front of any interior motion detectors and listen
for three beeps from the touchpad. The interior zone or description should appear on the display
and clear when you exit the protected area. Wireless motion detectors require a 3 minute delay
between activations.
6. Test all smoke detectors and follow the manufacturer’s instructions. The detector identification
should appear on the display.
7. When all protection points have been checked and are intact (e.g., closed), there should be no zone
identification number(s) displayed on the touchpad.
8. Before exiting test mode, check that there are no zone identification numbers displayed on the
touchpad and that all required sounds were activated and then silenced. If any confirming sounds
or zone identifications were not activated at the correct time, call for service immediately. Exit test
mode by entering your security code + [1]. Test mode will automatically shut off after 4 hours if not
manually turned off.
To learn more about testing your system, please visit System Testing.
Other System Information
Time & Date Programming
To View Current Date and Time
Enter your [security code] + [#] + [6] [3]. The time/date will remain for about 30 seconds.
To Set Date and Time
Enter your [security code] + [#] + [6] [3]. When the time/date are displayed, press [*]. Enter the 2-digit
hour setting. Press [*]. Enter the 2-minute setting. Press [1] for PM or [2] for AM. Enter the last two digits
of the current year. Enter the 2-digit month setting. Enter the 2-digit day setting. When the cursor is at the
last digit, press [*] or wait 10 seconds to exit.
Paging Features
Your system may be set up to automatically send alert messages to a pager when certain conditions
occur in your system. An installer can program your system to send a message about arming, disarming,
alarms, and trouble conditions. You can also program the system to send an automatic message in the
event that someone has not arrived home (no disarmament) within a defined period of time.
The pager display format is AAAAAAAAAAAAAAAA – BBB – CCCC

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Arepresents an optional 16 digit character string that can represent account numbers, PIN
numbers, or any other identifying data.
Brepresents the three digit code of the event that has occurred.
Crepresents the four digit code of a user or zone number.
The three digit event codes (BBBB) that can be displayed are 911 (alarm), 811 (trouble), 101 (system
disarmed), and 102 (system disarmed).
For example: 911-0004 reports an alarm (911) caused by fault zone 4 (0004) and 102-0005 reports
disarming system (102) by user 5 (0005). The optional 16 digit number is not included in these examples.
Single Button Paging and Latch Key Paging can be programmed by your installer. Single Button
Paging allows for a single button to be pre-programmed for a certain event. For example, you can
program your PAGER KEY to send a message 101-0004 to pager number 1 when the PAGER KEY is held
for two seconds. A working parent might be interested in Latch Key Paging, which will alert a parent, via
their pager and a secret code, if their child did not disarm the system at the scheduled time.
Scheduling
To Create a Schedule
Enter the [Master code] + [#] + [6][4]
Enter 2-digit schedule number (01-16) and press [*] to continue.
Enter the desired 2-digit event number:
00 = clear scheduled event
01 = turn a programmed output on or off
02 = grant a user access to schedules for one or more users
03 = send a latchkey report to a pager if the system is not disarmed by a specified time; the
message sent will be 777-7777
04 = automatically arm the system in stay mode at a specified time (pager report also sent)
05 = automatically arm the system in away mode at a specified time (pager report also sent)
06 = automatically disarm the system at a specified time (pager report also sent)
07 = display the word REMINDER at a specified time
Press [*] to continue.
For events 03-07:
Enter the partition number to be armed or disarmed, then press [*] to continue:
0 = arm all 1 = partition 1 2 = partition 2 3 = arm common area
Enter the event’s start time and the day(s) of the week:
Position the cursor under the desired days and use the [*] key to move forward.
Press 1 to select the day.
Press [*] to continue.
Enter the event’s start time.

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Enter the desired repeat option:
0 = no repeat
1 = repeat schedule weekly
2 = repeat schedule biweekly
3 = repeat schedule every third week
4 = repeat schedule every fourth week
Note: to make a schedule that happens every day, select all days with repeat option 1. To make a
schedule that runs for one week then stops, select every day with repeat 0.
Select the randomize option, if desired (these times will vary within 60 minutes of the hour):
Event Logging
The system records up to 100 events in a history log that can be viewed by the Master User. Please see
the manufacturer’s complete manual for an itemized code list.
To View the Event:
1. Enter the [master code] + [#] + [6] [0]
2. The system will display the most recent event as follows:
Event number, type of event (by code), zone/user number, partition (where the event
occurred), time, and date of event.
3. Pres [*] to display previous events, press to display future events.
4. To exit the Event Log, press any key other than [*] or [#].
Single Button Arming and Step Arming
Single Button Arming
Your system may be programmed for Single Button Arming, which allows for activating your alarm by
pressing a single function key only. You are not required to enter your user code upon arming, however
the system will require your code to disarm. In order to activate your single button arming, press and
hold the designated function key for two sections until the armed indicator is displayed. Please see the
manufacturer’s manual for a detailed explanation of this feature.
Single Button “Step” Arming
Your system may be programmed for Single Button “Step” Arming, which is similar to Single Button
Arming, however the designated function key can arm the system in any of three modes; Stay, Night-Stay,
and Armed-Away.
Quick Byass

Safewatch Pro 3000 System Manual
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Your system may be programmed for quick bypass. This allows for bypassing several protected zones
without having to enter the zone numbers individually. This feature is useful if, for example, you routinely
leave certain windows open when arming at night.
To active the Quick Bypass, enter your [security code] + [6] + [#]. Within a few moments, all open zones
will be displayed and automatically bypassed. Make sure that only those zones that you wish to leave
unprotected are bypassed and that you have not accidently left any zones unprotected. Now you can arm
your system as usual.
Additional Features
Using Device Commands
Your system may be programmed for this function. Please see the manufacturer’s manual for a detailed
explanation of this feature.
Accessing Other Partitions and Multi-Partition Arming
For information about accessing other partitions, please see the user manual for a detailed explanation
of this feature.
Other System Information
Communicating with the Panel
Your system can be set up to communicate with you through:
Status beeps
Alarm sirens
Touchpad text
Pager information
Instructing the Panel
Not just anyone can walk up to a touchpad and operate your security system. Before the system will
process most commands, users are required to enter a pre-programmed 4-digit access code.
Keychain touchpads that are enrolled as part of the system do not require an access code, but are
usually kept in an individual’s pocket or purse.
If you would rather use an actual key to arm and disarm the system, your security dealer can install a
special key and keyswitch in your home.