ADTRAN SMART/RG SR501n User manual

/ Gateway User Manual
Model: SR501
Release 1.3 March 2020
Firmware Version 2.6.2.4
501 SE Columbia Shores Boulevard, Suite 500
Vancouver, Washington 98661 USA
[phone] / smartrg.com

Table of Contents
Welcome! 3
Purpose & Scope 3
Intended Audience 3
Getting Assistance 3
Copyright and Trademarks 3
Disclaimer 4
Getting Familiar with your Gateway 5
LED Status Indicators 5
Connections 5
Buttons 6
ON/OFF Switch 6
Reset Button 6
Installing your SmartRG Gateway 7
Logging in to your SmartRG Gateway's UI 7
Device Info 8
Summary 8
WAN 9
Statistics 10
LAN 10
WAN Service 11
xTM 11
xDSL 12
References 16
Route 17
ARP 18
DHCP 18
DHCPv6 19
VPN 20
Advanced Setup 21
Layer2 Interface 21
ATM Interface 21
PTM Interface 24
WAN Service 27
PPP over Ethernet 27
IP over Ethernet 35
Bridging 45
LAN 49
IPv6 Autoconfig 52
Ethernet Config 53
NAT 55
Virtual Servers 55
Port Triggering 57
DMZ Host 59
Security 60
IP Filtering - Outgoing 60
IP Filtering - Incoming 61
MAC Filtering 63
Adding a MAC Filtering Rule 63
Parental Control 64
Time Restriction 64
URL Filter 66
Quality Of Service 66
QoS Config 67
Supported DSCP Values 67
QoS Queue Config 68
QoS Classification 70
QoS Port Shaping 72
Routing 74
Default Gateway 74
Static Route 75
Policy Routing 75
RIP (Routing Information Protocol) 76
DNS 78
DNS Server 78
Dynamic DNS 79
Static DNS 80
DSL 81
Advanced settings 83
UPnP 85
DNS Proxy 86
Interface Grouping 87
IP Tunnel 89
IPv6inIPv4 89
IPv4inIPv6 90
IPSec 91
Advanced IKE Settings 93
Certificate 94
Local 94
Trusted CA 96
Power Management 97
Multicast 98
Diagnostics 101
Diagnostics 101
Ethernet OAM 101
Ping Host 104
Trace Route to Host 105
Management 106
Settings 106
Backup 106
Update 106
Restore Default 107
System Log 108
Security Log 109
Management Server 110
TR-069 Client 110
STUN Config 113
Internet Time 115
Access Control 116
Accounts 116
Add an Account 116
Modify or Delete an Account 119
Default Passwords 119
Services 120
Passwords 121
Access List 121
Logout Timer 122
Update Software 123
Reboot 123
Logging Out 125
Appendix C: FCC Statements 126
FCC - Part 68 126
REN (RINGER EQUIVALENT NUMBERS)
STATEMENT 126
IC-CS03 statement 126
FCC Statement 127
FCC Radiation Exposure Statement 127
SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2019 1

Table of Contents
Canada Statement 127
5GHz 128
Revision History 129
SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2019 2

SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020 3
Welcome!
Thank you for purchasing this SmartRG product.
SmartRG offers solutions that simplify the complex Internet ecosystem. Our solutions include hardware, software, applications,
enhanced network insights, and security delivered via a future-proof operating system. Based in the USA, SmartRG provides local,
proactive software development and customer support. We proudly offer the best, most innovative broadband gateways available.
Learn more at www.SmartRG.com.
Purpose & Scope
This User Manual provides SmartRG customers with installation, configuration and monitoring information for the SR501 gateway.
Intended Audience
The information in this document is intended for Network Architects, NOC Administrators, Field Service Technicians and other net-
working professionals responsible for deploying and managing broadband access networks. Readers of this manual are assumed to
have a basic understanding of computer operating systems, networking concepts and telecommunications.
Getting Assistance
Frequently asked questions are provided at the bottom of the Subscribers page of the SmartRG Web site.
Subscribers: If you require further help with this product, please contact your service provider.
Service providers: if you require further help with this product, please open a support request.
Copyright and Trademarks
Copyright © 2020 by SmartRG, Inc., an ADTRAN company. Published by SmartRG, Inc. All rights reserved.
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, trans-
lated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, pho-
tocopying, manual, or otherwise, without the prior written permission of SmartRG, Inc.

SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020 4
Disclaimer
SmartRG does not assume any liability arising out of the application or use of any products, or software described herein. Neither
does it convey any license under its patent rights nor patent rights of others. SmartRG further reserves the right to make changes to
any products described herein without notice. This publication is subject to change without notice.
Any trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective
owners.

SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020 5
Getting Familiar with your Gateway
This section contains descriptions of the SR501 gateway's lights, ports, and buttons.
LED Status Indicators
Your SR501 gateway has four indicator lights (LEDs) on the front. The following table describes the LEDs and their functions.
LED Action Description
Internet Connected to Internet
Authentication failed.
DSL Connecting to DSL
Connected to DSL
Transferring data
LAN Connected to LAN
Transferring data
POWER Unit is on
Connections
Below is a diagram of how to install your SR501 gateway. This information is also in the Quick Start Guide enclosed with your gateway.
ON/OFF DSLPower Reset ETH
Phone jack
1
2
4
3
The ports depicted in this example are described below.

SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020 6
Port Description
Power Connect the power cord included with your gateway to this connector. Use only the power supply included with your gate-
way. Intended for indoor use only.
ETH The yellow RJ45 port on the back of your gateway is used to connect client devices such as computers and printers to your
gateway
DSL The grey RJ12 port labeled DSL is specifically intended for connection to an internet provider via a DSL (Digital Subscriber
Line) service.
Buttons
ON/OFF Switch
The ON/OFF toggle switch is located on the back of the gateway and turns the gateway on and off.
Reset Button
The Reset button is a small hole in the gateway's enclosure with the actual button mounted behind the surface. This style of push-
button prevents the gateway from being inadvertently reset during handling. Reset must be actuated with a paper clip or similar
implement.
The Reset button is located on the back of the unit.
This pin-hole sized reset button has three functions. The duration for which the button is held dictates which function is carried
out.
Hold Duration Effect
Less than 6
seconds
Performs a modem reset that is equivalent to the Reboot function in the gateway software.
6-20 seconds Performs the software equivalent to the Restore Defaults function in the gateway software.
20 or more seconds Changes the POWER LED to red and the gateway enters CFE mode which is a state associated with performing
firmware updates via Internet browser.

SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020 7
Installing your SmartRG Gateway
The following instructions explain all connection types offered for SmartRG gateways. For instructions specific to your gateway, fol-
low the instructions in the Quick Start Guide included in the box.
1. Attach your computer's RJ45 connection to the SmartRG gateway's LAN port.
2. If your computer is not already set up to acquire IP addresses using DHCP, configure your computer's IP interface to do so.
(For instructions on logging in to a SmartRG gateway configured for "bridge mode" operation, see the Note below.)
Logging in to your SmartRG Gateway's UI
To manually configure the SmartRG Gateway, you can access the gateway's embedded web UI.
1. Open a browser and enter the gateway's default address: http://192.168.1.1 in the address bar. The Authentication
Required dialog box appears.
2. Enter the default username and password: admin/admin, and click OK. The Device Info summary page appears.
Note: The gateway's UI can be accessed via the WAN connection by entering the WAN IP address in your browser's address bar and
entering the default username and password: support/support. WAN HTTP access control MUST be enabled to access the gateway's
UI via the WAN connection. For more information, see the Management Access Control section.
If your SmartRG gateway is configured for "bridge mode" (modem) operation, your PC will NOT be able to acquire an address via CPE
DHCP. Instead, manually configure your PC's interface with an IP address on the default network (e.g., 192.168.1.100).
The remainder of this guide is dedicated to a sequential walk-through of the gateway user interface. Screen captures are provided
along with descriptions of the options available on the pictured page. Where applicable, valid values are provided.
For in-depth "how-to" information for specific scenarios, look at the knowledge base found on our support web site. Access to this site
is restricted to SmartRG customers and partners. Do not share links to this site with your subscribers.

SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020 8
Device Info
In this section, you can view information about your gateway's setup, status or nature of its connection with the provider and with
LAN devices. You cannot change the settings in this section.
Summary
When you log into the gateway interface, the Device Info summary page appears. This page displays details about the hardware and
software associated with your gateway. In addition, the current status of the WAN connection (if present) is shown.

SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020 9
WAN
On this page, you can view information about the connection between your ISP and your gateway. The WAN interface can be DSL or
Ethernet and supports a number of Layer 2 and above configuration options (explained later in this document).
In the left navigation bar, click Device Info >WAN. The following page appears.
The fields on this page are explained in the following table.
Field Name Description
Interface The connection interface (Layer 2 interface) through which the gateway handles the
traffic.
Description The service description such ipoe_0_0_1, showing the type of WAN and its ID.
Type The service type. Options are PPPoE,IPoE, and Bridge.
VlanMuxId The VLAN ID. Options are Disabled or 0-4094.
IPv6 The state of IPv6. Options are Enabled and Disabled.
Igmp Pxy The IGMP proxy.
Igmp Src Enbl The IGMP source option is enabled for this connection.
MLD Pxy The MLD proxy.
MLD Src Enbl The MLD source option is enabled for this connection.
NAT The state of NAT. Options are Enabled and Disabled.
Firewall The state of the Firewall. Options are Enabled and Disabled.
Status The status of the WAN connection(s). Options are Disconnected,Unconfigured,Con-
necting, and Connected.