ADTRAN TOTAL ACCESS 234 User manual

TOTAL ACCESS 234 SHDSL NTU P/N 1200708L1
F
or more
d
e
t
a
il
e
d
d
ocumen
t
a
ti
on, v
i
s
it
us on
li
ne a
t
www.a
dt
ran.com
Quick Start Guide
Quick Start Guide, 61200708L1-13B, January 2005 Technical Support 1-888-4ADTRAN or [phone] Copyright © 2005 ADTRAN, All Rights Reserved
CONNECT THE CONSOLE INTERFACE
Before connecting to the Total Access 234 console interface, you will need the following items: VT100
terminal or PC (with VT100 terminal emulation software) and a straight through serial cable with a DB-9
(male) connector on one end and the appropriate interface for your terminal (or PC) on the other.
1. Connect the DB-9 (male) connector of your serial cable to the console port on the rear
panel of the unit.
2. Connect the loose end of the serial cable to the VT100 terminal or PC (with terminal
emulation software).
3. Open a VT100 terminal session to the Total Access 234 using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the
ADTRAN Command Line Interface (CLI).
CONFIGURE GATEWAY IP ADDRESSES/SUBNET MASK
Configure the Gateway IP addresses and subnet mask by following
these steps. If you are not sure what IP address to assign, please
contact your network administrator.
1. Enter enable to activate the Enable command security mode.
2. When prompted, enter the enable password (if configured).
3. Enter config terminal to activate the Global configuration mode.
4. Enter bre lan-gw 10.26.12.12 wan-gw 100.26.12.12 mask
255.255.255.0* to assign LAN and WAN Gateway IP addresses
and subnet mask.
*Note: Underlined text represents example entries only. Modify
them to match your configuration.
5. Enter exit to return to the Enable configuration mode.
6. Enter copy running-config startup-config to save the running
configuration to the unit’s non-volatile memory (NVRAM).
NET ETH
FEATURES
• One integrated EIA-232 configuration port (DCE)
• One integrated 10/100BaseT Ethernet port
• 2-Wire/4-Wire SHDSL interface
• WAN Protocol: ATM
• Command Line Interface (CLI)
• Management - EOC/CLI using Virtual Terminal
• Front panel LEDs
• Wall mounting available with additional parts
SPECIFICATIONS
DC Input Power 12 VDC nominal (8.5 VDC min, 18 VDC max); ITU-T standards: G.991.2
Diagnostics & Test Self-diagnosis; local loopback; remote loopback
EMC Emissions EN55022:1998 Class B; FCC Part 15 Class B
EMC Immunity, Power
Fault, and Lightning
EN55024:1998; EN61000-3-2; EN61000-3-3; Telstra 1563; K.21 (2004)
Enhanced
Electrical Safety EN60950; AS/NZS 60950; UL60950 3rd ed.;
CSA C22.2 No. 60950 3rd ed.; IEC 60950 CB Scheme
Telecom S043.2; G.991.2
Environmental Operating Temp: 0oC to 50oC; Storage Temp: -20oC to 70oC
*Note: No stacking should be done at 50oC. Up to three units can be stacked at room temperature.
Humidity: 95 percent noncondensing
Dimensions 9.3 inches W x 2.1 inches H x 6.1 inches D
Connectors SHDSL Port: RJ-45; 135 ohms; TNV-3 rated
10/100BaseT Ethernet: RJ-45
Console Port: DB-9 female
Power Input: Kycon KPJ-3S snap & lock or equivalent
Table standoff cannot be used with this unit.

TOTAL ACCESS 234 SHDSL NTU P/N 1200708L1
F
or more
d
e
t
a
il
e
d
d
ocumen
t
a
ti
on, v
i
s
it
us on
li
ne a
t
www.a
dt
ran.com
Quick Start Guide
Quick Start Guide, 61200708L1-13B, January 2005 Technical Support 1-888-4ADTRAN or [phone] Copyright © 2005 ADTRAN, All Rights Reserved
TOTAL ACCESS 234 LEDS
LED Color Indication
PWR Off
Green (solid)
No power present.
Power present.
SHDSL Off
Green (solid)
Yellow (solid)
Red (solid)
Unit is powered off.
Port is trained with no active alarm conditions.
Port is trained with minor active alarm
condition.
Port is attempting to train or is trained with a
major alarm condition.
LLOOP Off
Red (solid)
No local loop is active.
A local loop is active.
RLOOP Off
Red (solid)
No remote loop is active.
A remote loop is active.
BERT -- Not applicable with this product.
LNK Off
Green (solid)
Yellow (solid)
No Ethernet link present.
The 10BaseT Ethernet link is up.
The 100BaseT Ethernet link is up.
TD Off
Green (blinking)
No transmit activity on Ethernet port.
Transmit activity on Ethernet port.
RD Off
Green (blinking)
No receive activity on Ethernet port.
Receive activity on Ethernet port.
10/100BASET ETHERNET PORT PINOUT
Pin Name Description
1 TX1 Transmit Positive
2 TX2 Transmit Negative
3 RX1 Receive Positive
4,5 — Unused
6 RX2 Receive Negative
7,8 — Unused
CONSOLE PORT PINOUT
Pin Name Description
1 DCD Data Carrier Detect (output)
2 RD Receive Data (output)
3 TD Transmit Data (input)
4 DTR Data Terminal Ready (input)
5 SG Signal Ground
6 DSR Data Set Ready Tied to pin 1 (output)
7, 9 — Unused
8 CTS Clear to Send Tied to pin 1 (output)
WAN-SHDSL NETWORK PINOUT (RJ-45)
Pin Name Description
1 Tip 2 4-wire Loop 2 Pair Tip
2 Ring 2 4-wire Loop 2 Pair Ring
3 — Not connected
4 Tip 1 2-wire Pair Tip,
4-wire Loop 1 Pair Ring
5 Ring 1 2-wire Pair Ring,
4-wire Loop 1 Pair Ring
6-8 — Unused