ADTRAN 17600139F1 User manual

Q
uick Star
t
Overview
This quick start describes how to install ADTRAN’s 825-v6 Home Gateway Unit.
The 825-v6 WiFi 6 XGS-PON HGU is an indoor gateway that leverages XGS-PON technology for delivering premium multi-Gigabit services.
■“Installing the 825-v6 Gateway” on page 2
■“Understanding the Status LEDs” on page 4
■“Safety and Regulatory” on page 5
Figure 1 illustrates the front and back of the 825-v6 gateway.
Figure 1. Front and Back of the 825-v6 Gateway
WARNING!
f
Read all warning, cautions, notes and installation instructions before installing or servicing this equipment.
f ATTENTION!
Lisez tous les avertissements et mises en garde avant l’installation de cet équipement ou la réalisation de toute opération de maintenance
f WARNING! f CAUTION! g NOTE
WARNING indicates a hazard which, if
not avoided, could result in death, injury
or serious property damage.
CAUTION indicates a hazard which, if not
avoided, could result in service interruption,
damage to the equipment, or minor property
damage.
NOTES inform the user of additional, but
important, information or features.
ADTRAN
825-v6 Home Gateway Unit
Wi-Fi 6 XGS-PON HGU
May 2021
617600139-13A
P/N: 17600139F1

2 617600139F1-13A
Features
The features of the 825-v6 gateway include the following:
■ XGSPON network uplink
■ Subscriber interfaces
♦ 2.5 Gigabit Ethernet (RJ-45) interface
♦ 4x Gigabit Ethernet (RJ-45) interfaces
♦ 3x3 802.11ax @2.4GHz
♦ 4x4 802.11ax @5GHz
♦ 2x voice (RJ-11) interfaces
■ Remote activation and deactivation
■ Remote firmware upgrades
■ Remote OMCI management as per ITU-T G.988
Installing the 825-v6 Gateway
The following are guidelines for basic installation of the 825-v6.
Package Contents
■ ADTRAN’s 825-v6 WiFi 6 XGS-PON gateway
■12V DC power adapter
Prior to Installation
Before installing the equipment, inspect the gateway. If damage has occurred during shipping, file a claim with the carrier, and then contact ADTRAN
Customer Support. For more information, refer to the product warranty available online at https://adtran/wp_support_warranty.
Required Tools
Standard technician tools and, if installing the gateway on a wall, a #2 Phillips-head screwdriver, are required for installing the 825-v6.
Mounting Options
There are two options to install the 825-v6: desktop and wall mount. Be sure to route and secure the fiber and cables in a manner that will prevent
damage. These options are described below.
Desktop Installation
The 825-v6 can be placed on a desk or table. The following table shows the recommended minimum distance (in feet and meters) between the gateway
and household appliances to reduce interference.
NOTE
g
Refer to the national, state and local electrical codes for the requirements for power, grounding, wiring, and installation methods.
CAUTION!
f
The product is intended for indoor use only. Ethernet, POTS cables, and attached equipment are intended for use within the same building with
equipotential bonding, and not intended to be placed in separate buildings or structures. Failure to deploy as described could result in permanent
damage from lightning or other electrical events and voids the warranty. Furthermore, all connections from outside of the building, such as old POTS
wiring, must be disconnected prior to use.
Household Appliance Recommended Minimum Distance (in feet and meters)
Microwave ovens 30 feet / 9 meters
Baby monitor – analog 20 feet / 6 meters
Baby monitor – digital 40 feet / 12 meters
Cordless phone – analog 20 feet / 6 meters

617600139F1-13A 3
Wall Mount Installation
The 825-v6 can be mounted on a wall. Wall Mount Kit (17600192F1) can be ordered for mounting the 825-v6. Instructions are provided in the related
Quick Start Guide (617600192F1-13A).
Connecting the 825-v6 Gateway
Figure 2 illustrates the installation (connection) options for the 825-v6 gateway.
Figure 2. 825-v6 Gateway Installation Options
The following subscriber connections are available on the rear of the 825-v6:
■ 4x Gigabit Ethernet (RJ-45 Connectors) – LAN 1- 4 ports
■ 1x 2.5 Gigabit Ethernet port (RJ-45 Connector) - 2.5GbE port
■ 3x3 802.11ax @ 2.4GHz
■ 4x4 802.11ax @ 5GHz
■ 2x Telephone (RJ-11 Connectors) – Tel 1 and Tel 2 ports
■ 1x USB 3.0 (Type A Connector) - port
To connect the subscriber interfaces, refer to Figure 2 and complete the following:
1. For an Ethernet connection, insert a Category 5E (or better) RJ-45 cable into one of the LAN ports (labeled LAN 1- 4) or the 2.5 Gigabit Ether-
net port (2.5GbE) until there is an audible “click”.
Cordless phone – digital 30 feet / 9 meters
Bluetooth devices 20 feet / 6 meters
ZigBee 20 feet / 6 meters
WARNING!
f
Ensure that the 825-v6 does not come in contact with water or other liquids.
CAUTION!
f
Ensure that the 825-v6 is not located in direct sunlight or next to any thermal obstructions.
Household Appliance Recommended Minimum Distance (in feet and meters)

4 617600139F1-13A
2. For a Voice connection, insert an RJ-11 cable into one of the telephone ports labeled (Tel 1 or Tel 2) until there is an audible “click”.
Connecting the Power Supply
1. Connect the end of the power adapter to the Power port on the rear panel of the gateway
2. Plug other end of the power adapter into the wall outlet.
3. Confirm that the power is connected properly. The Power LED should be lit on the front of the gateway.
Resetting the Gateway
A reset button is available if the 825-v6 needs to be rebooted. To reboot the 825-v6, press the Reset button on the rear panel of the gateway for 5
seconds or less. To reset the device to custom defaults, press the Reset button for 5 seconds or more.
Understanding the Status LEDs
The LEDs on the back panel of the 825-v6 gateway enable you to monitor the device status. This section describes the three types of LEDs available on
the 825-v6 gateway. See Figure 3 for details.
Figure 3. Status LEDs
2.4 GHz / 5 GHz Status LEDs
The 2.4 GHz and 5 GHz status LEDs indicate the state of the wireless connections on the gateway.
WPS Status LED
The WPS status LED indicates the status of WPS (Wi-Fi protected setup).
Tel 1/2 Status LED
The Tel 1/2 status LED indicate the state of the phone line ports.
NOTE
g
Alternately, the device may be powered by a supported third-party UPS which may be connected via 7-pin molex connector, labeled UPS.
LED Color State Description
2.4 GHz
5 GHz
Green On Wi-Fi radio is UP.
Flashing Wi-Fi radio is transferring data.
None Off Wi-Fi connection is DOWN.
LED Color State Description
WPS Green On WPS is enabled. Flashing WPS is passing traffic.
None Off WPS is not active.
LED Color State Description
Tel 1/2 Green On Telephone is off-hook; a call is in progress.
Flashing Telephone is off-hook.

Product Specifications
Electrical
■ Power is provided by a 12V DC Power Adapter that is included with the 825-v6. The power adapter operates from a power source of 100 to 240V AC,
50 - 60 Hz. The nominal output is 12V DC +\–5% with a maximum current rating of 4.0 Amps. For US and Canadian applications, a UL Listed limited
power source (LPS) is required. For deployment outside of North America, an LPS specifically approved for that country, such as a CE Mark, is
required.
Environment
■ Operating Temperature: 32°F to 104°F (0°C to 40°C)
■ Storage Temperature: -40°F to 158°F (-40°C to 70°C)
■ Relative Humidity: 10 to 95 percent, non-condensing
Safety and Regulatory
This product meets the following compliance requirements:
■ UL /cUL Listed
■ FCC Part 15, Class B
■ ICES-003 (Class B)
■ IEC 62368-1
■ EN 62368-1, AS/NZS 60950.1
■ RoHS Compliant
This equipment contains no parts that can be serviced by the user.
Refer to the Safety and Regulator Notice for this product (P/N: 617600139F1-17) for detailed safety and regulatory information.
Consultez l'avis sur la sécurité et la conformité à la réglementation pour ce produit (P/N: 617600139F1-17) pour obtenir des renseignements détaillés sur
la sécurité et la réglementation.
Ausführliche Sicherheits- und regulatorische Informationen sind in der Konformitätserklärung zur Sicherheit und Einhaltung von Normen zu diesem
Produkt (P/N: 617600139F1-17) aufgeführt.
NOTE
g
It is strongly suggested that the power supply (a 5-foot (1.5 m) power cord) included with the 825-v6 be connected to a surge suppressor device
which can have its own extension cable. The surge protection device should provide L-N, L-G, and N-G protection. It is also recommended that
the device contains a visual 'GOOD' indicator.
NOTE
g
Changes or modifications not expressly approved by ADTRAN will void the warranty.
Documentation for ADTRAN Network Solutions products is
available for viewing and download directly from the ADTRAN
Support Community website.
Go to: https://supportcommunity.adtran.com
ADTRAN offers training courses on our products, including
customized training and courses taught at our facilities or at
customer sites.
For inquiries, go to: http://adtran.com/training
Access additional safety information and product documentation using the QR
code or website.
https://supportcommunity.adtran.com
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2021 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
617600139F1-13A