NetVanta ADSL Network Interface Module (ADSL over ISDN) P/N 1200889E1/L1
For more detailed documentation, visit us online at www.adtran.com.
Quick Start Guide
®
Quick Start Guide, 61200889E1-13D, July 2006 ADTRAN Technical Support +1-256-963-8716 Copyright © 2006 ADTRAN, All Rights Reserved
See the AOS Command Reference Guide on the
ADTRAN OS System Documentation CD for a
complete list of ATM commands.
ADSL NIM COMMANDS
retrain
Forces the modem to retrain.
snr-margin [showtime monitor l training monitor] <margin>
Enables monitoring and sets the minimum signal-to-noise (SNR) ratio
during training and showtime. Use the no form of this command to
disable monitoring.
showtime monitor Enables margin monitoring to retrain the ADSL
interface if the specified minimum margin is
violated during showtime.
training monitor Enables margin monitoring to retrain the ADSL
interface if the specified minimum margin is
violated during training.
<margin> Sets the minimum SNR margin in dB. Range is
1to15.
training-mode [G.DMT | G.LITE | Multi-Mode | T1.413 | ADSL |
ADSL2+ | READSL2]
Configures the ADSL training mode. This setting must match the service
provider’s DSLAM.
G.DMT Specifies ANSI full-rate mode. This is the only
training mode valid on the ADSL Annex B.
ATM COMMANDS
snmp trap link-status
Controls the Simple Network Management Protocol (SNMP) variable
ifLinkUpDownTrapEnable (RFC2863) to enable (or disable) the interface
to send SNMP traps when there is an interface status change. Use the
no form of this command to disable this trap.
ATM SUB-INTERFACE COMMANDS
access-policy <policyname>
Assigns a specified access policy for the inbound traffic on an interface.
Use the no form of this command to remove an access policy association.
<policyname> Identifies the configured access policy using an
alphanumeric descriptor (all access policy descriptors
are case-sensitive).
dynamic-dns [dyndns | dyndns-custom | dyndns-static] <hostname>
Configures Dynamic DNS service provided by Dynamic Network Services,
Inc. (www.dyndns.org).
dyndns Allows you to alias a dynamic IP address to a static
hostname in various domains. This service is provided
for up to five hostnames.
dyndns-custom Gives complete control over an entire domain name. A
web-based interface provides two levels of control
(basic or advanced) over the domain. Can be used
with both static and dynamic IPs.
dyndns-static Allows a hostname such as yourname.dyndns.org to
point to your IP address. This service is provided for
up to five hostnames.
encapsulation [aal5mux | aal5snap]
Configures the encapsulation type for the ATM Adaption Layer (AAL) of the
ATM Protocol Reference Model.
aal5mux Specifies encapsulation type for multiplexed virtual
circuits. A protocol must be specified.
aal5snap Specifies encapsulation type that supports LLC/SNAP
protocols.
oam-pvc managed <frequency>
Enables end-to-end F5 Operation, Administration, and Maintenance (OAM)
loopback cell generation and OAM management for an ATM interface. Use
the no form of this command to disable generation of OAM loopback cells.
<frequency> Specifies the time delay between transmitting OAM
loopback cells. Range is 0 to 600 seconds.
oam retry <up-count> <down-count> <retry-frequency>
Configures parameters related to OAM management for an ATM interface.
Use the no form of this command to disable OAM management
parameters.
<up-count> Specifies number of consecutive end-to-end F5 OAM
loopback cell responses that must be received in order
to change a PVC connection state to up. Range is
1 to 255.
<down-count> Specifies number of consecutive end-to-end F5 OAM
loopback cell responses that are not received in order
to change a PVC state to down. Range is 1 to 255.
<retry-frequency> Specifies frequency (in seconds) that end-to-end F5
OAM loopback cells are transmitted when a change in
the up/down state of a PVC is being verified. Range is
1 to 600.
