Advantech MIO-2363 User manual

User Manual
MIO-2363
Intel® Atom™ x6000E Series 2.5"
PICO-ITX SBC

MIO-2363 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2022
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated, or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. The information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties that may result from its use.
Acknowledgments
Intel® is a trademark of Intel® Corporation.
AMI is a trademark of American Megatrends, Inc.
IBM, PC, PS/2 and VGA are trademarks of International Business Machines Corpo-
ration.
Microsoft Windows®, DirectX® is a registered trademark of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
For more information on this and other Advantech products, please visit our websites
at:
http://www.advantech.com http://www.advantech.com/eplatform
For technical support and service, please visit our support website at:
http://support.advantech.com/
This manual is for the MIO-2363.
Part No. 2006236302 Edition 3
Printed in Taiwan February 2023

iii MIO-2363 User Manual
Product Warranty (2 years)
Advantech warrants the original purchaser that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products that have been repaired or altered by
persons other than repair personnel authorized by Advantech, or products that have
been subject to misuse, abuse, accident, or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events.
Because of Advantech’s high quality-control standards and rigorous testing, most
customers never need to use our repair service. If an Advantech product is defective,
it will be repaired or replaced free of charge during the warranty period. For out-of-
warranty repairs, customers will be billed according to the cost of replacement mate-
rials, service time, and freight. Please consult your dealer for more details.
If you believe your product to be defective, follow the steps outlined below.
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages displayed when the prob-
lem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain a return merchandise authori-
zation (RMA) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a completed Repair and Replacement
Order Card, and a proof of purchase date (such as a photocopy of your sales
receipt) into a shippable container. Products returned without a proof of pur-
chase date are not eligible for warranty service.
5. Write the RMA number clearly on the outside of the package and ship the pack-
age prepaid to your dealer.

MIO-2363 User Manual iv
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
type of cable is available from Advantech. Please contact your local supplier for
ordering information.
Test conditions for passing also include the equipment being operated within an
industrial enclosure. In order to protect the product from damage caused by electro-
static discharge (ESD) and EMI leakage, we strongly recommend the use of CE-
compliant industrial enclosure products.
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for assistance.
Technical Support and Assistance
1. Visit the Advantech website at www.advantech.com/support to obtain the latest
product information.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before calling:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

v MIO-2363 User Manual
Packing List
Before system installation, check that the items listed below are included and in good
condition. If any item does not accord with the list, contact your dealer immediately.
1 x MIO-2363 SBC
1 x USB cable 20cm (p/n: 1700030406-01)
2 x COM port cable 20cm (p/n: 1700030404-01)
1 x Audio cable 20cm (p/n: 1700019584-01)
1 x ATX power cable 20cm (p/n: 1700019705-01)
1 x Passive heatsink (p/n: 1970005240T001)
Standoff
1 x Startup manual
1 x DeviceOn package

MIO-2363 User Manual vi

vii MIO-2363 User Manual
Contents
Chapter 1 Introduction..........................................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications............................................................................................ 2
1.3 Block Diagram........................................................................................... 4
Chapter 2 Mechanical Specifications..................5
2.1 Introduction ............................................................................................... 6
2.2 Board Layout: Dimensions........................................................................ 6
Figure 2.1 MIO-2363 Mechanical Diagram (Top Side) ................ 6
Figure 2.2 MIO-2363 Mechanical Diagram (Bottom Side)........... 6
Figure 2.3 MIO-2363 Mechanical Diagram (Coastline) ............... 7
Figure 2.4 MIO-2363 Mechanical Diagram (with Heatsink) ......... 7
2.3 Quick Installation Guide ............................................................................ 8
2.3.1 Heatsink ........................................................................................ 8
Figure 2.5 MIO-2363 Heatsink Installation .................................. 8
Figure 2.6 MIO-2363 Heatsink Installation .................................. 8
Chapter 3 Installation............................................9
3.1 Jumper & Switches ................................................................................. 10
Table 3.1: Jumpers and Switches ............................................. 10
3.2 Connectors.............................................................................................. 10
Table 3.2: Connectors ............................................................... 10
3.3 Locating Connectors ............................................................................... 11
Figure 3.1 MIO-2363 Connector Locations (Bottom Side)......... 11
3.4 Setting Jumpers ...................................................................................... 11
3.4.1 Miscellaneous Switch (SW1) ...................................................... 12
3.4.2 Panel Voltage Selection (VDD1)................................................. 12
3.4.3 DC Power Input Connector (CN7) .............................................. 13
3.4.4 Audio Internal Connector: AUDIO1............................................. 13
3.4.5 USB2.0 Internal Connector: USB2.............................................. 14
3.4.6 LVDS Connector (LVDS1) .......................................................... 14
3.4.7 Panel Inverter Connector (BL1) .................................................. 16
3.4.8 COM Port Internal Connector 1 (COM1)..................................... 16
3.4.9 COM Port Internal Connector 2 (COM2)..................................... 17
3.4.10 GPIO Internal Connector (GPIO1) .............................................. 17
3.4.11 I2C Internal Connector (CN1) ..................................................... 18
3.4.12 Front Panel Internal Connector (CN5) ........................................ 18
3.4.13 M.2 Key-E Connector (M2_1) ..................................................... 19
3.4.14 M.2 Key-B Connector (M2_2) ..................................................... 21
3.4.15 RTC Battery Connector (BAT1) .................................................. 23
Chapter 4 AMI BIOS Setup .................................25
4.1 Entering Setup ........................................................................................ 26
4.1.1 Advanced BIOS Features Setup................................................. 27
4.1.2 Chipset Configuration ................................................................. 50
4.1.3 Security ....................................................................................... 62
4.1.4 Boot............................................................................................. 63
4.1.5 Save & Exit ................................................................................. 64

MIO-2363 User Manual viii
Appendix A System I/O Ports ............................... 65
A.1 System I/O Ports..................................................................................... 66
A.2 DMA Channel Assignments .................................................................... 66
A.3 1st MB Memory Map............................................................................... 67
A.4 Interrupt Assignments ............................................................................. 67

Chapter 1
1Introduction

MIO-2363 User Manual 2
1.1 Introduction
Advantech MIO-2363 is a 2.5” PICO-ITX form factor SBC (compact series, 100 x 72
mm; 3.9 x 2.8 in), powered by Intel® Atom® x6000E series. It provides embedded
iManager 3.0, SUSI 4.0, and Advantech’s WISE-DeviceOn to monitor and control
system operation effectively and remotely. MIO-2363 possess onboard LPDDR4x-
3733 and eMMC5.1 up to 128GB.
1.2 Specifications
Platform
Processor x6211E x6413E x6425E
Max. Frequency 3.0GHz 3.0GHz 3.0GHz
Base Frequency 1.3GHz 1.5GHz 2.0GHz
Core/Thread 2/2 4/4 4/4
L2 Cache 1.5MB 1.5MB 1.5MB
CPU TDP 6W 9W 12W
Chipset Intel® Chipset (SoC Integrated)
BIOS AMI UEFI 256Mbit
Memory
Technology LPDDR4x 3200 LPDDR4x 3200 LPDDR4x 3733
Max. Capacity 4GB 4GB 8GB
Channel/Socket Dual Channels/Onboard
ECC Support IBECC IBECC IBECC
Storage eMMC 64GB 64GB 128GB
Graphics
Controller Intel UHD Graphics for 10th Gen Intel Processor
Max. Frequency 750MHz 750MHz 750MHz
Base Frequency 350MHz 500MHz 500MHz
3D/HW
Acceleration
DX12, OGL4.5, OCL1.2, Vulkan 1.1; HW encode
HEVC/H.265, MPEG2, JPEG/MJPEG
Display I/F
LCD LVDS Dual Channel 18/24-bit LVDS
HDMI Up to 2160 x 3840 @30Hz
Multiple Display LVDS+HDMI
Ethernet
Controller 2 x RJ-45, LAN1: Intel i210, LAN2: Intel i210
Speed 10/100/1000 Mbps
External I/O
Ethernet 2 x RJ-45
VGA/HDMI/DP -/1/-
USB3.2/USB2.0 2/-
Power DC-Jack Optional

3 MIO-2363 User Manual
Chapter 1 Introduction
Internal I/O
SATA -
USB2.0 2
Serial Bus 1x I2C
COM Port 2 x RS-232/422/485
GPIO 8-bit general purpose input output I/O
Audio Realtek ALC888, Line-in/Line-out/MIC
Inverter 3.3V/5V/12V
LPC/SPI Bus eSPI for EIO-211/ SPI for TPM/no LPC
Front Panel
Control Power-on, Reset, Buzzer, SATA LED, CaseOpen
Board
Feature
Watchdog Timer Programmable 1 ~ 65535 sec/min
TPM TPM2.0 (Infineon SLB9670)
iManager 3.0 SW API for Hardware Monitor, Smart Fan Control,
Brightness Control, I2C, GPIO, WDT
Expansion M.2
1x M.2 E-Key for 2230 module (PCIex1, USB 2.0 to
support wireless module)
1x M.2 B-Key for 2242 module (SATA, USB 2.0 to sup-
port SATA storage; BOM option to PCIex1 to support
PCIe storage or RS-232 module
Power
Supply Voltage Vin: DC 12~24V +/- 10%; RTC Battery: Lithium 3V/
210mAH
Connector 2pin Power Connector (180D); Optional: DC-IN Jack
Power
Management AT, ATX
Max. Consumption TBU TBU 26.69W (12V);
28.7W (24V)
Idle Consumption TBU TBU 9.35W (12V);
11.6W (24V)
Environment
Temperature
Operating: Standard: 0 ~ 60° C (32 ~ 140° F),
Operating Extend: -40 ~ 85° C (-40 ~ 185° F)
Storage: -40 ~ 85° C (-40 ~ 185° F)
Humidity
Operating: 40° C @ 95% relative humidity, non-con-
densing
Storage: 60° C @ 95%relative humidity, non-condens-
ing
Vibration
Resistance 3.5 Grms
Certification EMC CE, FCC Class B
Mechanical
Dimensions 100 x 72 mm (3.9" x 2.8")
Net Weight 86g

MIO-2363 User Manual 4
1.3 Block Diagram
PCIex1
GbE1
2 x USB 3.1
2 x USB 2.0
COM1
RS-232/422/485
COM2
RS-232/422/485 GPIO 8b Watchdog
Multi-stage I2C
M.2 E-Key
2230
i210
PCIex1
DDI
GbE1
HDMI1.4
SPI 256M BIOS
eMMC 64/128GB
SPI TPM
eDP LVDS
eDP-to-LVDS
PTN3460
HDA Audio
Line-in/out/MIC
ALC-888
LPDDR4x LPDDR4x
Advantech
EIO-211
Onboard Memory 4GB/8GB
i210
USB3.1/2.0
PCIe, USB2.0
eSPI
M.2 B-Key
2242
SATA, USB2.0
PCIEx1
Intel Elkhart Lake
Atom x6000E Series
DC 12-24V, AT/ATX
External I/O
Internal I/O
Opt. Func.

Chapter 2
2Mechanical
Specifications

MIO-2363 User Manual 6
2.1 Introduction
The MI/O compact form factor SBC is a new-generation SBC designed with a variety
of mechanical improvements. This chapter includes board dimension and assembly
instructions for the standard thermal solution.
2.2 Board Layout: Dimensions
Figure 2.1 MIO-2363 Mechanical Diagram (Top Side)
Figure 2.2 MIO-2363 Mechanical Diagram (Bottom Side)

7 MIO-2363 User Manual
Chapter 2 Mechanical Specifications
Figure 2.3 MIO-2363 Mechanical Diagram (Coastline)
Figure 2.4 MIO-2363 Mechanical Diagram (with Heatsink)

MIO-2363 User Manual 8
2.3 Quick Installation Guide
This section introduces installation of the heatsink, which contains in the white box
inside the package. Please assemble it by following diagram. Remember to remove
the plastic from thermal pad before assembling.
2.3.1 Heatsink
Figure 2.5 MIO-2363 Heatsink Installation
Figure 2.6 MIO-2363 Heatsink Installation

Chapter 3
3Installation

MIO-2363 User Manual 10
3.1 Jumper & Switches
3.2 Connectors
Table 3.1: Jumpers and Switches
VDD1 Panel Voltage Selection Jumper
SW1 Miscellaneous Switch
Table 3.2: Connectors
Label Function
CN1 I2C Internal Connector
CN5 Front Panel Internal Connector
CN7 DC Power Input Connector
COM1 COM Port Internal Connector 1
COM2 COM Port Internal Connector 2
USB1 USB3.2 Connector
USB2 USB2.0 Internal Connector
LAN1 Dual RJ45 LAN Ports
HDMI1 HDMI Connector
GPIO1 GPIO Internal Connector
M2_1 M.2 Key-E Connector
M2_2 M.2 Key-B Connector
AUDIO1 Audio Internal Connector
BAT1 RTC battery Connector
LVDS1 LVDS Connector
BL1 Panel Inverter Connector

11 MIO-2363 User Manual
Chapter 3 Installation
3.3 Locating Connectors
Figure 3.1 MIO-2363 Connector Locations (Bottom Side)
3.4 Setting Jumpers
You may configure your card to match the needs of your application by setting jump-
ers. A jumper is a metal bridge used to close an electric circuit. It consists of two
metal pins and a small metal clip (often protected by a plastic cover) that slides over
the pins to connect them. To “close” a jumper, you connect the pins with the clip. To
“open” a jumper, you remove the clip. Sometimes a jumper will have three pins,
labeled 1, 2, and 3. In this case you would connect either pins 1 and 2, or 2 and 3.
The jumper settings are schematically depicted in this manual as follows:
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes. Generally, you
simply need a standard cable to make most connections.

MIO-2363 User Manual 12
3.4.1 Miscellaneous Switch (SW1)
3.4.2 Panel Voltage Selection (VDD1)
Part Number 1600000084
Description SLIDE SW CHS-04TA (29) SMD 8P 6.6x5.4x2.4mm
Setting Function
1ON: AT mode (Default)
OFF: ATX mode
2Reserved
3OFF: Normal (Default)
ON: Load BIOS Default
4ON: Top Swap Override ENABLE
OFF: Top Swap Override DISABLE
Part Number 1653003260
Description PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050
Jumper Short Panel Voltage
1-3 3.3V (Default)
3-5 5V
3-4 12V