Advantech WISE-4610 Series Installation and operation manual

WISE-4610 Startup Manual 1
Thank you for purchasing the WISE-4610 module. This
quick start guide is intended to help you with deploying the
module. It includes information on the power requirements
and application wiring. Should you require more instruc-
tions, please refer to the user manual.
The WISE-4610 has two pairs of external power inputs:
1. +Vs and -Vs (for line power or battery recharge)
2. Solar panel+ and solar panel- (for battery recharge)
Both power inputs support a standard industrial unregulated
24 VDC power supply. This series of modules also accept
+10 to +50 VDC power input and 200-mV peak-to-peak
power ripple. The immediate ripple voltage should be
between +10 and +50 VDC.
For modules with a lithium-ion battery, please note that the
operating temperature is 0~60°C (32~140°F). For safety
reasons, when the temperature is in the range of 45~60°C
(113~140°F), the battery can only be recharged to 20%.
• 1 x WISE-4610 wireless I/O module
• 1 x Waterproof antenna
• 1 x Mounting bracket
Note:
I/O board should be purchased respectively.
WISE-4610
Advanced Industrial LoRa/LoRaWAN IoT Wireless I/O
Module
Startup Manual
1. Download and install the USB driver from https://www.
silabs.com/products/development-tools/software/usb-to-
uart-bridge-vcp-drivers
2. Download and install WISE Studio from http://support.
advantech.com/
3. To power the module, connect a DC power source to
the +Vs and -Vs pins.
4. Connect the module to your computer via the micro-
USB port
5. Open WISE Utility and click Go To Serial Page.
6. Press Connect to link the WISE-4610 and you will then
seethewebcongurationpage.
7. UsewebcongurationinWISEUtilityorpressOpen in
Browsertoopenthewebcongurationinanybrowser
(Google Chrome is recommended).
8. Click Information to check whether your module has
successfully connected to a LoRa network. Once con-
nected,yourI/Omoduleisreadytobecongured.
Overview
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service:
http://support.advantech.com/
This startup manual is for WISE-4610 Series.
Part No. 2003461002
Printed in Taiwan
Edition 3
October 2020
Input Power Requirements
Packaging List
Battery Power
Quick Start for WISE-4610 Series

2 WISE-4610 Startup Manual
Pin Assignment of WISE-S600 I/O Module with M12 Connectors
M12
Connector
Model Name
M12 Cable WISE-S672 WISE-S614 WISE-S615 WISE-S617
Pin Number
PCB P/N 4-pin : 1700028162-01
8-pin : 1700028163-01 19A3DC7200-01 19A3DB1402-01 19A3DC1500-01 19A3DC1702-01
A
1 White DI 0 DI 0 RTD0+ AI 0+
2 Brown DI 1 DI 1 RTD0- AI 0-
3 Green DI 2 DI 2 RTD0 COM +12V Out0
4 Yellow DI 3 DI 3 NC +12V Out GND
5 Gray DI 4 NC RTD1+ AI 1+
6 Pink DI 5 NC RTD1- AI 1-
7 Blue NC NC RTD1 COM +12V Out1
8 Red DI COM DI COM NC +12V Out GND
B
1 White DATA0- AI 0+ RTD2+ DI 0
2 Brown DATA0+ AI 0- RTD2- DI 1
3 Green RS-232 TX AI 1+ RTD2 COM DI COM
4 Yellow RS-232 RX AI 1- NC DO 0
5 Gray DATA1- AI 2+ RTD3+ DO GND
6 Pink DATA1+ AI 2- RTD3- RS-485 D+
7 Blue NC AI 3+ RTD3 COM RS-485 D-
8 Red RS-232 GND AI 3- NC RS-485 GND
PWR
1 Brown +VS +VS +VS +VS
2 White -VS -VS -VS -VS
3 Blue SP+ SP+ SP+ SP+
4 Black NC SP- SP- SP-
Application Wiring

WISE-4610 Startup Manual 3
Application Wiring of WISE-S600 Series I/O Module with M12 Connectors
WISE-S614 (4AI/4DI)
WISE-S615 I/O Application Wiring
Solar Panel V-
Solar Panel V+
RTD
PT100 (385) : -200~+600°C
PT100 (392) : -200~+600°C
PT1000 : -40 ~+160°C
Pin Name Color of Cable
Wiring Pin Number Connector
RTD 0+ White 1
A
RTD 0- Brown 2
COM 0 Green 3
NC Yellow 4
RTD 1+ Gray 5
RTD 1- Pink 6
COM 1 Blue 7
NC Red 8
RTD 2+ White 1
B
RTD 2- Brown 2
COM 2 Green 3
NC Yellow 4
RTD 3+ Gray 5
RTD 3- Pink 6
COM 3 Blue 7
NC Red 8
+Vs Brown 1
PWR
-Vs White 2
Solar Panel V+ Blue 3
Solar Panel V- Black 4
Application Wiring (Cont.)

4 WISE-4610 Startup Manual
WISE-S617 (2AI/2DI/1DO/1RS-485)
WISE-S672 (6DI/1RS-485/1RS-485 or 1RS-232)
Application Wiring (Cont.)

WISE-4610 Startup Manual 5
Application Wiring of WISE-S600T Series I/O Module with Terminal Block
WISE-S614T (4AI/4DI)
WISE-S617T (2AI/2DI/1DO/1RS-485)
Application Wiring (Cont.)

6 WISE-4610 Startup Manual
• Please install the CP210x USB to UART Controller driver.
• USB is not able to power up the module, and please ensure to remove the USB cable before RF transmitting.
There are three ways to power up the WISE module, battery power, solar panel power and line power.
OpentherubbercoveronthesideoftheWISEmoduleandyoucanseeabatteryswitchforturningon/o󰀨thebatterypower.
For the solar power, it is not only to recharge the battery but also to power up the device.
Please refer to the application wiring section for solar panel power and line power pin assignment.
Also,thereisaUSBportforthedevicecongurationviaWISEStudiobutpleasenotethattheWISEdevicecannotbepow-
ered via USB.
Notes
Module Conguration

WISE-4610 Startup Manual 7
Led Indicators
The LED indicators are described as follows:
LED Color Indication Behavior
Status Green
Fast Blink
(0.2 sec ON,
0.3 sec OFF)
Wait for connecting or connecting
Slow Blink
(0.2 sec ON,
1.8 sec OFF)
Connecting and normal at work
Error Red
Fast Blink
(0.2 sec ON,
0.8 sec OFF)
Application errors
• Network registration timeout
• I/O error
Slow Blink
(0.2 sec ON,
2.8 sec OFF)
• Low battery voltage (V <= 20%)
• Low RTC battery voltage
O󰀨 No error
RF RX Green
On Receiving data from Gateway
O󰀨 NA
RF TX Yellow
On Sending data to Gateway
O󰀨 NA
Signal Strength*4 Green On
(after pressing membrane button)
Main battery capacity
• All OFF – V <= 20 %
• 1 ON – 20% < V < 40%
• 2 ON – 40% <= V < 60%
• 3 ON – 60% <= V < 80%
• 4 ON – V >= 80%