Advantech PCM-3347 Series User manual

PCM-3347 Series/
PCM-3348 Series
STPC Elite 133MHz Module with
SVGA/LCD/LAN Interface and
STPC Consumer II 133MHz CPU
Module with VGA/LAN/SSD/FDD
Users Manual

PCM-3347 User’s Manual ii
Copyright
This document is copyright ©, 2000 and 2002, by Advantech Co., Ltd.
All rights are reserved. The original manufacturer reserves the right to
make improvements to the products described in this manual at any time
without notice.
No part of this manual may be reproduced, copied, translated or transmit-
ted in any form or by any means without the prior written permission of
the original manufacturer. Information provided in this manual is
intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the
rights of third parties which may result from its use.
Acknowledgements
AMD is a trademark of Advanced Micro Devices, Inc.
Award is a trademark of Award Software International, Inc.
Cyrix is a trademark of Cyrix Corporation.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Microsoft WindowsÆ is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semiconductor Co., Ltd.
C&T is a trademark of Chips and Technologies, Inc.
UMC is a trademark of United Microelectronics Corporation.
Winbond is a trademark of Winbond Electronics Corp.
STPC is a trademark of SGS Thomson Corp.
For more information on this and other Advantech products, please visit
our website at:
http://www.advantech.com
http://www.advantech.com/ppc
For technical support and service, please visit our support website at:
http://www.advantech.com/support
This manual is for the PCM-3347F, PCM-3347L, PCM-3348F, PCM-
3348L.
Part No. 2006334710
1st. Edition Printed in Taiwan June 2003

iii
Packing List
Before you begin installing your card, please make sure that the following
materials have been shipped:
• PCM-3347 All-in-one single board computer
• 1 Start-up manual
• CD-ROM or Disks for utility, drivers, and manual (in PDF format)
• 1 2.5" IDE flat cable, 44-pin to 44-pin (product no. 1701440350)
• 1 KB/Mouse EXT Y-Cable (product no. 1703060053)
• 1 keyboard / PS2 mouse cable (product no. 1700060202)
• 3 serial port cables (product no. 1700100250)
•1 RS-422/485 cable (product no. 1700090301)
• 1 parallel cable (product no. 1700260250)
• 1 26-34 pin FDD cable converter (product no. 9681000044)
• 1 floppy cable, for 3.5" FDD only (product no. 1701340600)
• 1 VGA cable (product no. 1701160150)
• 1 LAN cable (product no. 1701100202)
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.

PCM-3347 User’s Manual iv

v Table of Contents
Contents
Chapter 1 General Information ........................................2
1.1 Introduction ....................................................................... 2
1.2 Features ............................................................................. 3
1.3 Specifications .................................................................... 3
1.3.1 Standard SBC functions.................................................. 3
1.3.2 VGA function (PCM-3347 only).................................... 4
1.3.3 VGA function PCM-3348............................................... 4
1.3.4 Ethernet function............................................................. 4
1.3.5 Solid state disk ................................................................ 4
1.3.6 Mechanical and environmental....................................... 4
1.4 Board Dimensions ............................................................. 5
Figure 1.1:PCM-3347 Dimensions ................................. 5
Chapter 2 Introduction ......................................................8
2.1 Connectors (PCM-3348 has no LCD connectors)............. 8
Table 2.1:Connectors ...................................................... 8
2.2 Locating connectors ........................... 10
Figure 2.1:Locating connectors (component side) ....... 10
Figure 2.2:Locating connectors (solder side) ............... 11
2.3 Installation Procedures ......................... 12
2.4 Ethernet connector (CN2) (PCM-3347F/3348F) ............ 12
2.4.1 Ethernet connector (CN2)............................................. 12
2.5 LCD-A display connector (CN7) .................................... 12
2.6 Serial ports (CN5, CN6, CN8, CN9)............................... 13
2.6.1 COM1,COM3,COM4 RS-232 port (CN6,CN9,CN8) .. 13
2.6.2 COM2 RS-232/422/485 port (CN5, CN23).................. 13
Table 2.2:Serial port default settings ............................ 13
2.7 EIDE HDD connector (CN1) .......................................... 13
2.7.1 Connecting the hard drive............................................. 13
2.8 PC/104 connector (CN17, CN19) ................................... 14
2.9 Parallel port connector (CN12) ....................................... 14
2.10 Backlight connector (CN3) PCM-3347........................... 14
2.11 VGA connector (CN10) .................................................. 14
2.11.1 CRT display connector (CN10) .................................... 15
2.12 Reset button connector (CN13)....................................... 15
2.13 Main power (+5 V / +12 V) connector (CN14) .............. 15
2.14 PS/2 Keyboard/mouse connector (CN18) ....................... 15
2.15 5 V connector (CN16)..................................................... 16
2.16 FDD connector (CN22)................................................... 16
2.16.1 Connecting the floppy drive ......................................... 16

PCM-3347 User’s Manual vi
2.17 LCD-B connector (CN11)............................................... 17
2.18 CompactFlash™ socket (CN22) ..................................... 17
2.19 I2C BUS (CN4).............................................................. 17
2.20 HDD LED connector (CN15) ......................................... 17
2.21 SIR connector (CN20)..................................................... 18
Chapter 3 Software Configuration .................................20
3.1 Introduction ..................................................................... 20
3.2 Connections for four standard LCDs (PCM-3347) ......... 20
3.2.1 Sharp LM64183P,LM64P89 (640x480 DSTN MONO
LCD) ....................................... 20
Table 3.1:Sharp LM64183P & LM64P89 .................... 20
3.2.2 Toshiba LTM10C042(640x480 TFT color LCD) ........ 21
Table 3.2:Connections to Toshiba LTM10DC042 ....... 21
3.2.3 Sharp LM64C142(640x 480 DSTN color LCD) .......... 22
3.2.4 Connections to Toshiba LTM12C275A (800 x 600 TFT
color LCD)....................................................................... 23
3.3 Ethernet software configuration ...................................... 24
Chapter 4 Award BIOS Setup.........................................28
4.1 System test and initialization........................................... 28
4.1.1 System configuration verification................................. 28
4.1.2 Further CMOS Data Safeguards ................................... 28
4.2 Award BIOS setup .......................................................... 29
4.2.1 Entering setup ............................................................... 29
4.2.2 Standard CMOS setup .................................................. 30
Figure 4.1:BIOS setup initial screen............................. 30
4.2.3 Advanced CMOS setup ................................................ 31
Figure 4.2:Standard CMOS setup screen...................... 31
4.2.4 Advanced chipset setup ................................................ 31
Figure 4.3:Advanced chipset setup............................... 31
4.2.5 Power management setup ............................................. 32
Figure 4.4:Power management setup............................ 32
4.2.6 PCI / Plug and Play configuration ................................ 32
Figure 4.5:Plug and Play Configuration ....................... 32
4.2.7 Peripheral setup............................................................. 33
Figure 4.6:Peripheral setup ........................................... 33
4.2.8 Load BIOS defaults ...................................................... 33
4.2.9 Change password .......................................................... 33
4.2.10 Save settings and exit.................................................... 34
Figure 4.7:Save and exit settings .................................. 34
4.2.11 Exit without saving ....................................................... 34
Chapter 5 SVGA Setup....................................................36
5.1 Introduction ..................................................................... 36
5.1.1 Chipset .......................................................................... 36

vii Table of Contents
5.1.2 Display memory............................................................ 36
5.2 Installation of SVGA driver ............................................ 36
5.2.1 Installation for Windows 3.1 ........................................ 37
5.2.2 Installation for Windows 95 ......................................... 40
Chapter 6 PCI SVGA Setup ............................................48
6.1 Introduction ..................................................................... 48
6.1.1 Chipset .......................................................................... 48
6.1.2 Display memory............................................................ 48
6.1.3 Display types................................................................. 48
6.2 Installation of the SVGA Driver ..................................... 49
6.2.1 Installation for Windows 3.1 ........................................ 49
6.2.2 Installation for Windows 95 ......................................... 53
6.2.3 Installation for Windows NT ........................................ 58
6.3 Further information ......................................................... 62
Chapter 7 PCI Bus Ethernet Interface...........................64
7.1 Introduction ..................................................................... 64
7.2 Installation of Ethernet driver ......................................... 64
7.2.1 Installation for MS-DOS and Windows 3.1.................. 64
7.2.2 Installation for Windows 95/98 .................................... 65
7.2.3 Installation for Windows NT ........................................ 69
7.3 Further information ......................................................... 72
Appendix A Programming the Watchdog Timer .............74
A.1 Programming the watchdog timer ................................... 74
Appendix B Installing PC/104 Modules ............................78
B.1 Installing PC/104 modules .............................................. 78
Table B.1:PCM-3347/PCM-3348 PC/104 (CN12)....... 80
Appendix C Pin Assignments .............................................84
C.1 Ethernet connector (CN2) ....................... 84
Table C.1:Ethernet connector (CN2) ............................ 84
C.2 LCD-A connector (CN7)........................ 85
C.3 COM1, COM3, COM4 connector (CN6, CN 9, CN8) ... 86
Table C.3:COM1,COM3,COM4 (CN6,CN 9,CN8) ..... 86
C.4 COM2 connector (CN5, CN23) ...................................... 87
C.5 EIDE hard drive connector (CN1) .................................. 88
Table C.6:EIDE hard drive connector (CN1) ............... 88
C.6 PC/104 connector (CN17, CN19) ................................... 89
C.7 Parallel port connector (CN12) ................... 89
Table C.7:Parallel port connector (CN12).................... 89
C.8 Backlight connector (CN3) ...................... 90
Table C.8:Backlight connector (CN3) .......................... 90
C.9 VGA connector (CN10) ........................ 90
Table C.9:VGA connector (CN10)............................... 90

PCM-3347 User’s Manual viii
C.10 Reset button connector (CN13)................... 91
Table C.10:Reset button connector (CN13) ................. 91
C.11 Main power (+5 V) connector (CN14) ............. 92
Table C.11:Main power (+5 V) connector (CN14) ...... 92
C.12 PS/2 keyboard/mouse connector (CN18) ........... 92
Table C.12:PS/2 keyboard/mouse connector (CN18)... 92
C.13 5 V connector (CN16) .......................... 93
C.14 FDD connector (CN22)................................................... 94
Table C.14:FDD connector (CN22).............................. 94
C.15 LCD-B connector (CN11) ....................... 95
Table C.15:LCD-B connector (CN11).......................... 95
C.16 CompactFlash™ socket (CN21) ..................................... 96
Table C.16:CompactFlash™ socket (CN21) ............... 96
Figure C.1:CompactFlash™ socket .............................. 97
Table C.17:I2C BUS connector (CN4)......................... 97
Appendix D System Assignments .....................................100
D.1 System I/O ports............................................................ 100
Table D.1:System I/O ports ........................................ 100
D.2 DMA channel assignments............................................ 101
Table D.2:DMA channel assignments ........................ 101
D.3 Interrupt assignments .................................................... 102
D.4 1st MB memory map .................................................... 103
Table D.4:1st MB memory map ................................. 103
Appendix E LCD Services ..................................................98
E.1 LCD Services .................................................................. 98

CHAPTER
1
General Information
This chapter gives background infor-
mation on the 3347/PCM-3348.
Sections include:
• Introduction
• Features
• Specifications
• Board dimensions

PCM-3347 User’s Manual 2
Chapter 1 General Information
1.1 Introduction
The PCM-3347 is the ultimate cost-effective PC/104 solution for limited-
space applications. It offers all the functions of an AT-compatible indus-
trial computer on a single board, and occupies less space than a 3¾" hard
drive. The PCM-3347 comes with an embedded STPC Elite 133MHz
processor on board. The PCM-3348 comes with an embedded STPC Con-
sumer II processor on board. For maximum performance, the PCM-3347
also supports on board memory that can accept up to 32/64 MB memory.
Onboard features include a socket for a CompactFlash™ Card, 100Base-
T Ethernet, Enhanced IDE interface, one parallel port, four serial ports
(RS-232), a keyboard, and a PS/2 mouse interface. A SVGA LCD display
controller allows CRT resolutions up to 1024 x 768 @ 16bpp colors, LCD
resolutions up to 1024 x 768 @ 16bpp colors. There is no LCD support
for the PCM-3348 series.
If you need any additional functions, the PCM-3347/PCM-3348 has a PC/
104 connector for future upgrades.

3 Chapter1
1.2 Features
• Ultra-compact size single board computer, smaller than a 3¾" hard disk
drive (96 mm x 90 mm)
• Onboard STPC Elite 133MHz/Cousumer II CPU
• Onboard 32/64 MB system memory, default is 32MB
• Onboard VGA/36-bit LCD interface PCM-3347 Series
• Supports CompactFlash™ card
• Built-in Enhanced IDE (AT bus) hard disk drive interface
• Onboard PS/2 keyboard/mouse connector
• Three serial ports (RS-232) and one RS-232/422/485 port.
• Upgradeable through PC/104 module
• Green engine with sleep mode and low power consumption
• +5 V power supply (for CPU board), +12 V power supply (for PC/104,
backlight)
• Onboard 10/100Base-T Ethernet interface
1.3 Specifications
1.3.1 Standard SBC functions
• CPU: ST Thomson STPC Elite 133MHz(PCM-3347) or Consumer II
(PCM-3348)
• BIOS: Award 256 KB Flash BIOS, supports Plug & Play
• Fanless operation
• DRAM: On board can be 32/64 MB SDRAM (default is 32MB)
• SSD: Supports one CompactFlash™ card
• Network: RTL 8100BL chipset
• Watchdog: 1.6 sec interval watchdog timer (optional flexible interval
available)
• IDE interface: One Enhanced IDE
PC/104 expansion: 104-pin 16-bit PC/104 module connectors

PCM-3347 User’s Manual 4
1.3.2 VGA function (PCM-3347 only)
• Controller: C&T 69000, supports CRT and 36-bit LCD
• Display memory: 2 MB SDRAM built-in
• Display resolution: 1024 x 768 @ 16 bpp (CRT), 1024 x 768 @ 16
bpp (LCD)
Resolution Map for PCM-3347 Series
1.3.3 VGA function PCM-3348
• Display memory: 512 KB ~ 4 MB share memory, set in BIOS
• Display type: Supports CRT
• CRT display mode: Non-interlaced CRT monitors resolutions up to
1280 x 1024 @ 24 bpp
1.3.4 Ethernet function
• Chipset: RTL 8100BL
• Ethernet interface: PCI 10/100 Mbps Ethernet. IEEE 802.3u protocol
compatible
• Connection: Onboard 10-pin 2 mm connector
1.3.5 Solid state disk
• Supports CompactFlash™ cards
1.3.6 Mechanical and environmental
• Operating voltage: +5 V only
• Power consumption: +5 V @ 1.62 A (typical) @ STPC Elite 133 MHz
CPU +32 MB
• Size (L x W): 96 mm x 90 mm (3.77" x 3.54")
• Weight: 0.103 kg (0.227 lb)
• Operating temperature: 0 ~ 60° C (32 ~ 140° F)
Resolution Colors
256 64K 16M
640 x 480 OK OK OK
800 x 600 OK OK OK
1024 x 768 OK OK NG

5 Chapter1
1.4 Board Dimensions
Figure 1.1: PCM-3347 Dimensions

PCM-3347 User’s Manual 6

CHAPTER
2
Introduction
This chapter tells how to set up the
PCM-3347 hardware. It includes
instructions on setting jumpers and
connecting peripherals, switches and
indicators. Make sure you read all the
safety precautions before you begin the
installation procedure.

PCM-3347 User’s Manual 8
Chapter 2 Introduction
2.1 Connectors (PCM-3348 has no LCD connectors)
The board has a number of connectors that allow you to configure your
system to suit your application.
The tables below shows the function of each of the board's connectors:.
Table 2.1: Connectors
Label Function
CN1 Primary connector
CN2 Ethernet connector
CN3 Backlight connector
CN4 I2C connector
CN5 COM2 (RS232/422/485) connector
CN6 COM1 connector
CN7 LCD 40 Pin connector
CN8 COM4 connector
CN9 COM3 connector
CN10 VGA connector
CN11 LCD 20 Pin connector
CN12 Parallel connector
CN13 Reset connector
CN14 Power connector
CN15 HDD LED connector
CN16 CPU FAN connector
CN 17 PC104 AT connector
CN18 PS/2 Keyboard and Mouse connector
CN19 PC104 XT connector
CN20 SIR connector
CN21 Compact Flash (Secondary IDE Master)
CN22 FDD connector
CN23 COM2 RS422/485
J1 Setting COM2 RS232/422/485 function

9 Chapter2
J2 Clear CMOS
J3 Setting WatchDog trigger event
BT1 Battery Socket
Table 2.1: Connectors

PCM-3347 User’s Manual 10
2.2 Locating connectors
Warning: Make sure you use the correct component side.
Improper installation can cause serious damage
to your hardware!
Figure 2.1: Locating connectors (component side)

11 Chapter2
Figure 2.2: Locating connectors (solder side)

PCM-3347 User’s Manual 12
2.3 Installation Procedures
2.4 Ethernet connector (CN2) (PCM-3347F/3348F)
The PCM-3347F is equipped with a high performance 32-bit PCI-bus
Fast Ethernet interface which is fully compliant with IEEE 802.3u 100/
10Base-T specifications. It is supported by all major network operating
systems.
The medium type can be configured via the RSet8139.EXE program
included on the utility disk. (See Chapter 5 for detailed information.)
2.4.1 Ethernet connector (CN2)
10/100Base-T connects to the PCM-3347F and PCM-3348 via an adapter
cable to the 10-pin 2 mm connector.
2.5 LCD-A display connector (CN7)
CN7 is a 40-pin dual-in-line header and is used to connect an LCD dis-
play to the PCM-3347F.
Warning: Always completely disconnect the power cord
from your board whenever you are working on it.
Do not make connections while the power is on,
because sensitive electronic components can be
damaged by a sudden rush of power.
Caution: Always ground yourself to remove any static
charge before touching the board. Modern elec-
tronic devices are very sensitive to static electric
charges. Use a grounding wrist strap at all times.
Place all electronic components on a static-dissi-
pative surface or in a static-shielded bag when
they are not in the chassis.