Advantech PCM-261 Installation and operation manual

1 PCM-261Startup Manual P/N:2006026101
PCM-261 LVDS/TTL to DVI Module
Startup Manual
Before you begin installing your card, please make sure
that the following materials have been shipped:
• 1 PCM-261
• 1 Startup manual
If any of these items are missing or damaged, contact
your distributor or sales representative immediately.
Optional Accessory:
• 1700000851:24bit TTL to 24 bit TTL cable
• 1700000840:18bit LVDS to 18 bit LVDS FOR 855GME
• 1700000853:24 bit LVDS to 24 bit LVDS
• 1700000827:18 bit LVDS T0 18 bit LVDS
• Chipset: Silicon Image SiI 164
• LVDS Input: 24,18bit LVDS
• Resolution:1024 x 768, 800 x 600, 640 x 480
• TFT Connector:Hirose or Pin Header
• External Power:+5V
• LCD connector Hirose or pin header
Mechanical and Environmental
• Dimensions (L x W): 72 x 62 mm (3.8" x 3.5")
• Weight: 30g
• Operating Temperature: 0 ~ 60°C(32~140°F)
• Storage temperature: -40 ~ 85°C(-40~185°F)
• Operating Humidity: 0%~90% ralative humity,non-con-
densing
• Power Supply Voltage: 5V
• Power Requirements: 5V @100mA
LVDS/TTL to DVI panel transfer module
Suitable for TFT LCD Panel Adapter
Packing list Specifications
Note 1: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded at:
www.adobe.com/Prodindex/acrobat/read-
step.html(Acrobat is a trademark of Adobe.)
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/epc
For technical support and service, please visit our
support website at:
http://service.advantech.com.tw/eservice/
This manual is for the PCM-261 series Rev. A1.
Part No. 2006026101 2nd Edition
Jan. 2005
Features
PCM-261 LVDS/TTL to DVI ModuleCA-6773 ISA IntelPCM-3351 SBC 3351 SBC Low Power Intel Tilamook

2 PCM-261 Startup Manual P/N:2006026101
Connectors on the board link it to external devices, such
as hard disk drives, a keyboard or expansion bus connec-
tors. In addtion, the board has a number of jumpers that
allow you to configure your system to suit your applica-
tion.
The table below lists the function of each of the jumpers
and connectors.
Jumpers & Connectors
Connectors
Label Function
CN1 AT SMALL POWER Connector
CN2 24 pin D-sub
CN3 LCD 40-Pin HIROSE (24 bits)
CN4 TTL 40-Pin HIROSE (24 bits)
(PCM-261T-A0A1 only)
CN1
Pin Pin name
1NC
2GND
3GND
45V
CN2
Pin Pin name
1 TMDS_TX2-
2 TMDS_TX2+
3GND
4NC
5NC
6 DDC CLOCK
7 DDC DATA
8NC
9 TMDS_TX1-
10 TMDS_TX1+
11 GND
12 NC
13 NC
14 +5V
15 GND
16 NC
17 TMDS_TX0-
18 TMDS_TX0+
19 GND
20 NC
21 NC
22 GND
23 TMDS_TXCLK+
24 TMDS_TXCLK-
CN3
Pin Pin name Pin Pin name
1NC 2NC
3 GND 4 GND
5NC 6NC
7 24LVDSD0- 8 18LVDSD0-
9 24LVDSD0+ 10 18LVDSD0+
11 GND 12 GND
13 24LVDSD1- 14 18LVDSD1-
15 24LVDSD1+ 16 18LVDSD1+
17 GND 18 GND
19 24LVDSD2- 20 18LVDSD2-
21 24LVDSD2+ 22 18LVDSD2+
23 GND 24 GND
25 24LVDSCLK0- 26 18LVDSCLK0-
27 24LVDSCLK0+ 28 18LVDSCLK0+
29 GND 30 GND
31 NC 32 NC
33 GND 34 GND
35 24LVDSD3- 36 NC
37 24LVDSD3+ 38 NC
39 NC 40 NC

3 PCM-261 Startup Manual P/N:2006026101
Dimensions
Component Placement
CN4
Pin Pin name Pin Pin name
1NC 2NC
3 GND 4 GND
5NC 6NC
7NC 8GND
9PD0 10PD1
11 PD2 12 PD3
13 PD4 14 PD5
15 PD6 16 PD7
17 PD8 18 PD9
19 PD10 20 PD11
21 PD12 22 PD13
23 PD14 24 PD15
25 PD16 26 PD17
27 PD18 28 PD19
29 PD20 30 PD21
31 PD22 32 PD23
33 GND 34 GND
35 SHFCLK 36 FLM(V-SYNC)
37 M/(DE) 38 LP(H-SYNC)
39 NC 40 NC
Board Layout