Advantech PCM-3665 PC/104-Plus Installation and operation manual

PCM-3665 Startup Manual 1
PCM-3665 PC/104-Plus Dual Giga
Ethernet LAN Module
Startup Manual
The powerful, new PC/104-plus dual Giga Ethernet LAN
module is designed to support the ever increasing number
of network connected embedded products on the market.
It can be applied to any size form factor CPU board by
employing the PC/104-plus throughput connectors. The
PCM-3665 can provide a single or dual ethernet configura-
tion using combinations of Intel’s 82541PI ethernet
chipsets (see ordering information below). The PCM-3665
provides full 32-bit performance, PCI bus capability and is
in full compliance with IEEE 802.3u 100Base-T specifica-
tions and IEEE 802.3x Full Duplex Flow Control.The PCM-
3665 is your off-the-shelf solution that can immediately
provide one or two ethernet ports to your embedded sys-
tem.
The PCM-3665 module includes a built-in 10 pin box
header and RJ-45 connectors. Two diagnostic LEDs indi-
cate the operating status of the module and the network.
You can define LEDs according to the application. The
PCM-3665 comes with drivers for a wide variety of net-
worksandoperatingsystems.
Before you begin installing your card, please make sure
that the following materials have been shipped:
If any of these items are missing or damaged, contact
y o u r d i s t r i b u t o r o r s a l e s r e p r e s e n t a t i ve i m m e d i a t e l y.
Standard Functions
• Chipset: Intel 82541PI
• Single/Twin Ethernet Port: PCM-3665-00A1E Dual
Giga LAN with RJ45 con; PCM-3665P-00A1E Dual Giga
LAN w/o RJ45 con; PCM-3665-01A1E Single Giga LAN
w/o RJ45 con.
• Network Port: Provide a standare IEEE 802.3 Ethernet
Interface for 1000Base-T, 100Base-TX, and 10Base-T
applications (802.3, 802.3u, and 802.3ab)
• Compatability: PCI version 2.2, 33MHz PCI
• Expansion Interface: PC104+ (ISA bypass)
Mechanical and Environmental
• Power Consumption: Dual LAN: +5V @ 1.2A (typical);
Single LAN: +5V @ 0.6A (typical)
• Power Requirements: +5V +/-5% tolerance on power
supply
• Dimensions (L x W): 96 x 90 mm (3.8" x 3.5")
• Weight: 0.084kg (0.185 Ib)
• Operating Temperature: 0 ~ 60°C(32~140°F)
• Storage Temperature: -40 ~ 85°C(-40~185°F)
• Operating Humidity: 0%~90% relative humity,non-con-
densing
Introduction Specifications
Packing list
• 1 Startup Manual for PCM-3665
• 1 CD-ROM for PCM-3665 Driver/Utility
• 1 Giga LAN cable for PCM-3665-01A1E
• 2 Giga LAN cable for PCM-3665P-00A1E
Note 1: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded at:
www.adobe.com/products/acrobat/
readstep2.html(Acrobat is a trademark of
Adobe.)
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the PCM-3665 series Rev. A1.
Part No.2006366500 1st Edition
May. 2006
PCM-3665 PC/104-Plus Dual Giga Ethernet LAN Module 430TX/SODIMM/LAN/USB/CRT/LCD/COM/DOC
CM-3351

2 PCM-3665 Startup Manual
Connectors on the board link it to external devices, such as
hard disk drives, a keyboard or expansion bus connectors.
In addition, the board has a number of jumpers that allow
you to configure your system to suit your application.
The table below lists the function of each of the jumpers
and connectors.
Locating connector (component side)
Mechanical Drawing (component side)
Mechanical Drawing (solder side)
Jumpers & Connectors
Jumper
J1 PCI VIO Select
S1 PCI INT Select
Connectors
Label Function
CN1 PC104- Connector
CN3 LAN1 RJ45 Connector
CN4 LAN1 Internal Connector
CN5 LAN1 LED Connector
CN6 LAN2 Internal Connector
CN7 LAN2 RJ45 Connector
CN8 LAN2 LED Connector
Board Layout

PCM-3665 Startup Manual 3
Jumper Settings
Jumper setting
J1: PCI VIO Select
Pin Function
1-2* +5V
2-3 +3.3V
*: Default
S1: PCI INT Select
SW (2,1) LAN1
ON, ON PCI_REQ#0 PCI_GNT#0 PCI_CLK#0 PCI_IDSEL#0 PCI_INTA#
ON, OFF PCI_REQ#1 PCI_GNT#1 PCI_CLK#1 PCI_IDSEL#1 PCI_INTB#
OFF, ON PCI_REQ#2 PCI_GNT#2 PCI_CLK#2 PCI_IDSEL#2 PCI_INTC#
OFF, OFF PCI_REQ#3 PCI_GNT#3 PCI_CLK#3 PCI_IDSEL#3 PCI_INTD#
SW (4,3) LAN2
ON, ON PCI_REQ#0 PCI_GNT#0 PCI_CLK#0 PCI_IDSEL#0 PCI_INTA#
ON, OFF PCI_REQ#1 PCI_GNT#1 PCI_CLK#1 PCI_IDSEL#1 PCI_INTB#
OFF, ON PCI_REQ#2 PCI_GNT#2 PCI_CLK#2 PCI_IDSEL#2 PCI_INTC#
OFF, OFF PCI_REQ#3 PCI_GNT#3 PCI_CLK#3 PCI_IDSEL#3 PCI_INTD#
This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undes-
ired operation
This equipment has been tested and found to comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this device in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his/her own expense. The user is advised that any equipment
changes or modifications not expressly approved by the party responsible for compliance would void
the compliance to FCC regulations and therefore, the user's authority to operate the equipment.
Caution!
Achtung!
There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge,
force open, or heat the battery. Replace the battery only with the same or equivalent type recom-
mended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.