Advantech ARK-1382 User manual

User Manual
ARK-1382

ARK-1382 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2008
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No. 2006138200 Edition 1
May 2008

iii ARK-1382 User Manual
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Packing List
Before installation, please ensure the following items have been shipped:
Item Part Number
–1 ARK-1382 unit
–1 Utility CD
–1 Registration and 1 year Warranty card Rev. A
–1 2-Pole Phoenix to DC-Jack Power Cable 1700001394
–1 DVI-I to VGA connector
–1 WLAN antenna ( ARK-1382W version)
Ordering information
Model Number Description
ARK-1382-S0A1E
Intel ULV Celeron 1.06GHz, 2 x Serial ports,1 x Giga LAN, 4 x USB 2.0, 2 x
DVI-I ,Ultra Compact, Fanless Embedded Box Computer
ARK-1382W-S0A1E
Optional accessories
1757000222 AC-to-DC Adapter DC19 V/3.42 A 65 W, with Phoenix
Power Plug, 0 ~ 40° C for Home and Office Use
1750003222 802.11b/g 5dBi Dipole Antenna
1700001947 Power Cable 2-pin 180 cm, USA type
1700001948 Power Cable 2-pin 180 cm, Europe Type
1700001949 Power Cable 2-pin 180 cm, UK Type
9666K10000E DIN-Rail mounting kit for ARK-1000 series models
9666K10001E VESA mounting kit for ARK-1000 series models

ARK-1382 User Manual iv

v ARK-1382 User Manual
Contents
Chapter 1 General Introduction ...........................1
1.1 Introduction ...............................................................................................2
1.2 Product Feature ........................................................................................3
1.2.1 General.........................................................................................3
1.2.2 Display..........................................................................................3
1.3 Chipset......................................................................................................4
1.3.1 Functional Specification................................................................4
1.3.2 Mechanical Specification ..............................................................7
Figure 1.1 ARK-1382 Dimensions...............................................7
1.3.3 Electrical Specification..................................................................8
1.3.4 Environmental Specification..........................................................8
Chapter 2 H/W Installation....................................9
2.1 Jumpers ..................................................................................................10
2.1.1 Jumper Description.....................................................................10
2.1.2 Jumper Setting............................................................................11
2.1.3 Locating Jumpers on the Board..................................................13
2.2 Connectors..............................................................................................14
Figure 2.1 ARK-1382 Front Side External I/O Connectors........14
Figure 2.2 ARK-1382 Rear Side External I/O Connectors.........14
2.2.1 ARK-1382 Front Side External I/O Connectors ..........................15
Figure 2.3 COM Connector........................................................15
Table 2.1: COM Standard Serial Port Pin Assignments............15
Figure 2.4 USB Connector.........................................................15
Table 2.2: USB Connector.........................................................16
Figure 2.5 Ethernet Connector ..................................................16
Table 2.3: RJ-45 Connector Pin Assignments...........................16
2.2.2 ARK-1382 Rear Side External I/O Connectors...........................17
Figure 2.6 DVI-I Connector........................................................17
Table 2.4: DVI-I Connector Pin Assignment..............................17
Figure 2.7 eSATA/USB Connector............................................18
Table 2.5: eSATA/USB Connector Pin Assignment..................18
Figure 2.8 Power Input Connector.............................................18
Table 2.6: Power Connector Pin Assignments..........................18
Chapter 3 BIOS Operation..................................19
3.1 BIOS Introduction....................................................................................20
3.2 BIOS Setup .............................................................................................20
3.2.1 Main Menu..................................................................................21
3.2.2 Standard CMOS Features ..........................................................22
3.2.3 Advanced BIOS Features ...........................................................23
3.2.4 Advanced Chipset Features........................................................25
3.2.5 Integrated Peripherals.................................................................26
3.2.6 Power Management Setup .........................................................27
3.2.7 PnP/PCI Configurations..............................................................29
3.2.8 PC Health Status ........................................................................29
3.2.9 Frequency/Voltage Control.........................................................30
3.2.10 Load Optimized Defaults.............................................................30
3.2.11 Set Password..............................................................................31
3.2.12 Save & Exit Setup.......................................................................32
3.2.13 Exit Without Saving.....................................................................32

ARK-1382 User Manual vi
Chapter 4 Full Disassembly Procedure............ 33
4.1 Introduction............................................................................................. 34
Figure 4.1 Unscrew the 4 screws on the bottom side................ 34
Figure 4.2 Unscrew the 6 screws on the front side frame ......... 35
Figure 4.3 Unscrew the 1 screws on the front face plate .......... 35
Figure 4.4 Unscrew the 4 Hex-bolt on the front face plate........ 36
Figure 4.5 Unscrew the 6 screws on the rear side frame.......... 36
Figure 4.6 Unscrew the 4 Hex-bolt on the rear face plate......... 37
Figure 4.7 Unscrew the antenna mounting screw..................... 37
Figure 4.8 Pull out the carrier board from the Aluminum case on
bottom side, and be careful for the thermal pad....... 38
Figure 4.9 Memory Socket ........................................................ 38
Figure 4.10MiniPCI Socket......................................................... 39
Figure 4.11Jumper Setting ......................................................... 39
Figure 4.12Install the board on the bottom side and be careful for
thermal pad .............................................................. 40
Appendix A RealtekRTL8111B/8111CGigabitBoot
Agent Configuration Menu41
A.1 Realtek RTL8111B/8111C Gigabit Boot Agent Configuration Menu ...... 42

Chapter 1
1General Introduction

ARK-1382 User Manual 2
1.1 Introduction
ARK-1382 is a fanless and ultra compact system designed for a wide range of appli-
cations, such as Point of information system, flight information display system, and
vehicle video player system.
ARK-1382 designed with Intel Celeron M 423 @ 1.06 GHz, which provides the excel-
lent computing and multimedia performance. The system Equipped with 802.11b/g
WLAN card and supports wide range of input voltages from 9 VDC to 35VDC. More-
over, to fitting in the different application, ARK-1382 supports dual DVI-I independent
display or dual VGA with clone mode. With the smallest size, ARK-1382 still support
4 x USB 2.0, 1 x Giga LAN and 2 x COM ports, user can install or take the CF card by
the external CF socket easily.
The ARK-1382 Compact Embedded Computer is equipped with a solid state onboard
CF card of up to 8 GB, so it easily passes 50 and 5 Grms shock and vibration tests.
ARK-1000 can be standalone, wall-mounted, DIN-rail mounted or VESA mounted.
The series accepts a wide range of power supplies (DC power in) and comes in a
footprint of only 189 x 41 x 130.6 mm (7.44" x 1.61" x 5.14"). The rugged cast alumi-
num case not only provides great protection from EMI, shock/vibration, cold and
heat, but also passive cooling for quiet fanless operation.

3 ARK-1382 User Manual
Chapter 1 General Introduction
1.2 Product Feature
1.2.1 General
CPU Intel/Celeron M ULV 423 at 1.06 GHz
System Chipset: 945GM chipset 533 MHz FSB
BIOS: AWARD® 4 Mbit Flash BIOS
System Memory: 200-pin SODIMM socket, support ECC Double Data Rate
(DDR2) 128 MB to 1 GB, DDR2 400/533 MHz
Power Management: APM1.2, ACPI 2.0 support
SSD: Supports CompactFlash® Card TYPE I/II (shared 1st IDE Channel) USB
memory
Watchdog Timer: Single chip Watchdog 255-level interval timer, setup by soft-
ware
Expansion Interface: 1 x miniPCI ( Equipped with miniPCI WLAN card for
ARK-1382W version)
Battery: 3V/210 mAh
I/O Interface: 2 x RS232/422/485 (default is RS-232, RS-422/485 by jumper
setting)
USB: 4 x USB 2.0 compliant Ports
Audio: ALC203 AC97 surround stereo sound and dual output 2.2 W amplifier.
Supports Line-out ( Left and Right)
IrDA: N/A
GPIO: N/A
LAN Chipset: Realtek 8111B PCI-E 10/100/1000 Base-T
Speed: 10/100/1000 Mbps
Interface: 1 x RJ45
Standard: IEEE 802.3u 100Base-T
1.2.2 Display
Chipset: Intel 945GM integrated 2D/3D graphic controller
Memory Size: Supports Intel DVMT (Dynamic Video Memory Technology) 3.0 1
MB or 8 MB under system BIOS
Resolution: CRT Display mode: pixel resolution up to 1600 x 1200 at 85-Hz
and 1600 x 1200 at 75-Hz LCD Display mode:
Display Interface: 2 x DVI-I, (VGA interface can be extended by connector)
Dual Independent: DVI + DVI; DVI + VGA; (VGA +VGA only supports clone
mode)

ARK-1382 User Manual 4
1.3 Chipset
1.3.1 Functional Specification
1.3.1.1 Processor
For ARK-1382W-S0A1E, ARK-1382-S0A1E.
1.3.1.2 Chipset
Processor
CPU supports:
Support 533 MHz Source-Synchronous Processor System Bus
Support Intel Celeron ULV423 at 1.06 GHZ CPU
35 mm *35 mm Micro-FCBGA Package.
Memory
NB: Intel 945GM GMCH chip supports:
Supports for 400/533 MHz DDR2 SDRAM devices with max
Supports maximum 1GB DDR SDRAM.
SO-DIMM Socket on board: 200 pin SO-DIMM socket type x 1
It may have compatibility issue for 2 GB memory, please check with Advantech
support team.
Graphic
and Video
Controllers
NB: Intel 945GM GMCH chip supports:
Internal Graphics Features
Dual display choose on board: Dual DVI, Dual VGA or DVI + VGA through
OS Driver
–DVI-I ( CRT )
Integrated 400-MHz, Three 8-bit DACs provide the R,G and B signal to
the monitor
Supports pixel resolution up to QXGA
Supports for Display Hot Plug
Supports Dual VGA Display via Video Separate Amplifier
–DVI-I ( DVI )
Supports DVI 1.0 for External Digital Monitor
Supports for Display Hot Plug
DVI Transmitter Support Digital Visual Interface (DVI) Transmitter up to
165M pixels/second
Supports Dual DVI Display Independently
WinXP Extended desktop support for Dual DVI and DVI + VGA
DVI-I Connector on board: DVI-I Combined Conn. 29P 90D(F) x 2
IDE
Interface
SB: Intel NH82801GHM chip supports:
Supports PIO IDE transfers up to 16 Mbytes/sec
Supports Ultra ATA transfers to 100/66/33 Mbytes/sec
The IDE interface integrates 16x32-bit buffers for optimal transfers
Supports Compact Flash Card Type II Socket
 CF Socket on board: CF Type II 50P 90D(M) external connector x 1

5 ARK-1382 User Manual
Chapter 1 General Introduction
Audio
Link
SB: Intel NH82801GHM chip supports:
Supports Audio Codec’97, Revision 2.3 specification
Supports Link for Audio and Telephony CODECS
Supports Dual 2.2W Audio Amplifier Plus Stereo
RCA Jack on Board: 3P 90D(F) Red x 1 ( Right Channel )
RCA Jack on Board: 3P 90D(F) White x 1 ( Left Channel )
USB
Interface
SB: Intel NH82801GHM chip supports:
USB host interface with support for 5 USB 2.0 ports ( 1 combined with
eSATA )
All ports are High-Speed, Full-Speed, and Low-Speed capable
Supports legacy keyboard/mouse software
USB dual connecter on board: USB conn 8P 90D(M) DIP x 2
USB + eSATA connecter on board : E-SATA+USB 11P 90D(M) DIP x 1
eSATA
Interface
SB: Intel NH82801GHM chip supports:
Supports the Serial ATA specification Revision 1.0a
Supports several optional sections of Serial ATA II: Extensions to Serial
ATA 1.0 Specification, Revision 1.0
USB + eSATA connecter on board : E-SATA+USB 11P 90D(M) DIP x 1
Note: eSATA do not support PnP function.
Mini PCI
Interface
SB: Intel NH82801GHM chip supports:
Supports Mini PCI Interface 1.0
Supports Mini PCI WLAN extension card use only
Supports 802.11A/B/G when use 9680005627
Mini PCI socket: MINI PCI 124P 180D(F) SMD x 1
(ARK-1382W version, miniPCI is equipped with WLAN miniPCI card)
Power
Manage-
ment
SB: Intel NH82801GHM chip supports:
Supports ACPI 3.0
ACPI Power Management Logic Support
Power connecter: Plug-In block 2P DIP x 1
BIOS
SB: Intel NH82801GHM chip supports:
Low Pin Count (LPC) interface support
Firmware Hub (FWH) interface support
Phoenix 4M bit Flash BIOS, supports Plug & Play, APM 1.2/ACPI 1.1.
Socket: 32 pin PLCC socket x 1

ARK-1382 User Manual 6
1.3.1.3 Others (chipset)
Serial
Ports
Super I/O: Winbond W83627HG supports:
2 full function serial ports by Winbond W83627
Support IRQ Sharing among serial ports on XPE
COM1: Supports to RS-232/422/485 and setting by Jumper
COM2: Supports to RS-232/422/485 and setting by Jumper
COM connecter: D-SUB CON. 9P 90D(M)DIP x 2
Note:RS-485 does not support Auto flow control. Please refer to CH2 for jumper
setting.
Thermal
sensor
Super I/O: Winbond W83627HG supports:
Monitor the current CPU temperature
Monitor the main power voltage
LAN
LAN Chip: Realtek RTL8111B-GR supports:
Supports PCI Express 1.0a
Integrated 10/100/1000 transceiver
Fully compliant with IEEE 802.3 compliant
Supports Wake on LAN and remote wake-up
Giga LAN Phone Jack on board: Phone Jack conn 8P 90D DIP x 1
Audio
Audio Codec: Realtek ALC203
Amplifier: National LM4863
Compliant with AC’97 2.3 specifications
Supports to 20-bit DAC and 18-bit ADC resolution
Supports Dual 2.2W Audio Amplifier Plus Stereo
RCA Jack on Board: 3P 90D(F) Red x 1 ( Right Channel )
RCA Jack on Board: 3P 90D(F) White x 1 ( Left Channel )
DVI
DVI Transmitter: Chrontel CH7307C x 2
Digital Visual Interface (DVI) Transmitter up to 165M pixels/second
High-speed SDVO (1G~2Gbps) AC-coupled serial differential RGB
inputs
Complete Windows and DOS driver support
DVI hot plug detection
DVI-I Connector on board: DVI-I Combined Conn. 29P 90D(F) x 2
VGA
Video Amplifier: Linear LT6557 x 2
Supports Dual VGA Display via Video Separate Amplifier
Share with DVI-I Connector on board: DVI-I Combined Conn. 29P
90D(F) x 2

7 ARK-1382 User Manual
Chapter 1 General Introduction
1.3.2 Mechanical Specification
1.3.2.1 Dimension (mm)
189 x 41 x 130.6mm
(7.44” x 1.61” x 5.14”)
Figure 1.1 ARK-1382 Dimensions
Battery
backup
Battery support: CR2032
BATTERY 3V/210 mAh with WIRE x 1
WLAN
(Optional)
Wireless LAN Module Card: WM3210
Supports Mini PCI Interface 1.0
Supports 802.11 b/g
Mini PCI socket: MINI PCI 124P 180D(F) SMD x 1
Unit: mm

ARK-1382 User Manual 8
1.3.2.2 Weight (g)
1.15 kg
1.3.3 Electrical Specification
1.3.3.1 Power Supply Voltage
Voltage requirement with Adaptor:
9 V-3.8 A ~ 35 V-1 A Adaptor
1.3.3.2 Power Supply Current
Supply Current (Maximum)
CPU : Intel Celeron ULV423 1.06 , RAM:533MHz 512GB DDR2 SDRAM
1.3.3.3 RTC Battery
Norminal Voltage: 3.0 V
Nominal discharge capacity: 210 mAh
1.3.4 Environmental Specification
1.3.4.1 Operating Temperature
The Intel® Celeron® is specified for proper operation when the junction temperature
is within the specified range of 0° C to 100° C.
The Intel® 945GM chipset temperature runs at a maximum of 100° C. The Intel®
ICH7 I/O Controller Hub 7 ( 82801GHM) case temperature runs at a maximum of
110° C.
The processor protects itself from catastrophic overheating by use of an internal ther-
mal sensor at a temperature level of approximately 135° C.
Operating temperature: 0 ~ 60° C (32 ~ 140° F)
1.3.4.2 Operating Humidity
Operating Humidity: 0% ~ 90% Relative Humidity, non-condensing
1.3.4.3 Storage Temperature
Standard products (0 ~ 60° C)
Storage temperature: -20 ~ 70° C
1.3.4.4 Storage Humidity
Standard products (0 ~ 60° C)
Relative humidity: 95% @ 60° C
Adaptor 19 V
Dos 0.86 A
BIOS NC
WINXP Idle 0.88 A
WINXP HCT11.0 NC
WINXP 3DMARK2001SE NC
WINXP
BURN IN TEST 1.16 A
Suspend 0.66 A

Chapter 2
2H/W Installation

ARK-1382 User Manual 10
2.1 Jumpers
2.1.1 Jumper Description
Cards can be configured by setting jumpers. A jumper is a metal bridge used to close
an electric circuit. It consists of two metal pins and a small metal clip (often protected
by a plastic cover) that slides over the pins to connect them. To close a jumper, you
connect the pins with the clip. To open a jumper, you remove the clip. Sometimes a
jumper will have three pins, labeled 1, 2 and 3. In this case you would connect either
pins 1 and 2, or 2 and 3.
The jumper settings are schematically depicted in this manual as follows.
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes.
Warning! To avoid damaging the computer, always turn off the power supply
before setting jumpers. Clear CMOS. Before turning on the power sup-
ply, set the jumper back to 3.0 V Battery On.
123

11 ARK-1382 User Manual
Chapter 2 H/W Installation
2.1.2 Jumper Setting
2.1.2.1 COM1 Jumper
ARK-1382 series of embedded box computer provide a jumper - JP1 ~ JP3 located
on the internal carrier board for COM1 selecting the RS-232, RS422 and RS485.
2.1.2.2 COM2 Jumper
ARK-1382 series of embedded box computer provide a jumper - JP1 ~ JP3 located
on the internal carrier board for COM2 selecting the RS-232, RS422 and RS485.]
JP1
Close pins Function
1-3 RS-232*
2-4 RS-232*
3-5 RS-422/RS-485
4-6 RS422/RS-485
(*): means default setting of the jumper/function.
JP2
Close pins Function
1-3 RS-232*
2-4 RS-232*
3-5 RS-422/RS-485
4-6 RS-422/RS-485
(*): means default setting of the jumper/function.
JP3
Close pins Function
1-2 RS-485
3-4 RS-422
5-6 RS-232*
(*): means default setting of the jumper/function.
JP4
Close pins Function
1-3 RS-232*
2-4 RS-232*
3-5 RS-422/RS-485
4-6 RS422/RS-485
(*): means default setting of the jumper/function.
JP5
Close pins Function
1-3 RS-232*
2-4 RS-232*

ARK-1382 User Manual 12
2.1.2.3 CMOS Jumper (JP8)
ARK-1382 series of embedded box computer provide a jumper - JP8 located on the
internal carrier board for selecting the CMOS of Clear or Normal status.
3-5 RS-422/RS-485
4-6 RS-422/RS-485
(*): means default setting of the jumper/function.
JP6
Close pins Function
1-2 RS-485
3-4 RS-422
5-6 RS-232*
(*): means default setting of the jumper/function.
Close pins Function
1-2 Clear CMOS
2-3 Normal*
(*): means default setting of the jumper/function.

13 ARK-1382 User Manual
Chapter 2 H/W Installation
2.1.3 Locating Jumpers on the Board

ARK-1382 User Manual 14
2.2 Connectors
Figure 2.1 ARK-1382 Front Side External I/O Connectors
Figure 2.2 ARK-1382 Rear Side External I/O Connectors
COM1 COM2 ON/OFF
USB4 USB2
USB3 USB1
LAN
Alarm LED
Normal LED
Compact Flash HDD LED
PWR LED
GN DVCC