Advantech 8GE(PoE)+2GE+2G SFP User manual

User Guide
8GE(PoE)+2GE+2G SFP Colorful LCD Display PoE Switch

- 2 -
Package Contents
Check the following contents of your package:
 PoE Switch x 1
 User’s Manual x 1
 Power Cord x 1
 Accessories(hanging ears*2, Rubber Feet*4, screw*8)
If any part is lost and damaged, please contact your local agent immediately.
1. Introduction
Thank you for choosing this PoE Switch. The 8GE(PoE)+2GE+2G SFP LCD Display PoE Switch Provides
have 8-10/100/1000Mbps PoE RJ45 Port witch 2-10/100/1000Mbps RJ45 Port and 2-1000Mbps SFP Slot. Its
PoE ports can automatically detect and supply power with those IEEE 802.3af/at compliant Powered
Devices (PD). The electrical power is transmitted along with data in one single cable allowing you to
expand your network where there are no power lines or outlets, where you wish to fix devices such as AP, IP
Cameras or IP Phones, etc.
The LCD not only can display the PoE work status, accurate judgment port of load, can also help customer
and engineer timely discover and solve the network failure, improve work efficiency and quality.
Port Feature
Model
Gigabit RJ45 Port
Gigabit SFP
Port
LCD Display
PSE Port
8GE(PoE)+2GE+2G SFP
Port1~10
Port11~12
Support
Port1~8

- 3 -
2. Hardware Description
2.1 Front Panel
The Front Panel of the PoE Ethernet Switch Consists of Ethernet Ports. The LCD Display and LED indicators
are also located on the panel
LED indicator
LED
Color
Function
PWR
Green
Off: No Power supply.
Light: Indicates the switch has power.
LNK/ACT
Orange
Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is successfully
established at 10/100Mbps.
Blink: Indicates that the Switch is actively sending or
receiving data over that port.
Green
Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is successfully
established at 1000Mbps.
Blink: Indicates that the Switch is actively sending or
receiving data over that port.
PoE
Orange
Off: No PoE powered device (PD) connected.
Light: There is a PoE PD connected to be port, which
supply power successfully.
Blink: Indicates port abnormal power supply.

- 4 -
Rear Panel
The rear panel of the PoE Switch indicates an AC inlet power socket, which accepts input power from
100 to 240V AC, 50/60HZ.
LCD Features
The PoE Switch with the function of the LCD display and PoE. The LCD can display the working condition of
PoE port not only, still can accurately show the state of each port such as :Output power,Overload,Short
circuit,Light load ,Low voltage ,Over voltage High temperature, and so on

- 5 -
Not only such visible on the basis of three generations in the second generation increases the color logo,
according to the menu button, switch mode, bandwidth display and warning, PD type, PSE power fine-tuning and
priority, PoE port switch control, LCD switch. Enhance the LCD viewing angles, smart fan control, language selection and
the function of the factory Settings, in turn, as shown in the figure below: See the operation instructions of the screen
concretely.
3. Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it .Please follow
the following instructions in avoid of incorrect installation causing device damage and security
threat.
Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with wet
cloth or liquid;
Do not place the switch near water or any damp area. Prevent water or moisture from entering the
switch chassis;
Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a
fall;
Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of
Obstruction;
Make sure that the operating voltage is the same one labeled on the switch ;
Do not open the chassis while the switch is operating or when electrical hazards are present to avoid
electrical shocks;

- 6 -
Desktop Installation
Install the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at
each corner of the Switch in case of the external vibration. Allow adequate space for ventilation
between the device and the objects around it.
3.2.Rack mountable Installation
The switch is rack-mountable and can be installed on an EIA-19 inch equipment rack. To do this, first,
please install the mounting brackets on the switch’s side panels (one on each side), secure them with
the included screws, and then use the screws provided with the equipment rack to mount the switch on
the 19 inch rack.

- 7 -
3.3 Turn on the switch
Please plug the power supply into the switch, the internal power system of the switch can Auto-regulate the
working power according to the actual input power. When the switch is power on, the power indicator will be
light on the front panel of the switch shines.
Note: Please confirm the voltage is correct before power on, otherwise the switch will be damaged.
(There is a power supply socket on the back panel of the PoE Ethernet switch. The power input is:
100V-240Vac, 50/60Hz.)

- 8 -
Specifications
Model
8GE(PoE)+2GE+2G SFP
Standard
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3x,IEEE802.3af, IEEE802.3at
Network -
Media(Cable)
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e cable (≤100m)
1000BASE-X: MMF or SMF SFP module(Optional)
LCD Display
Support
MAC Address Table
8K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T/X: 1488095pps/Port
Switching Capacity
24Gbps
1
2
.
8
G
Dimensions (L*W*H)
280*180*44mm
Fan
Fan
Power Input
AC: 100~240V, 50/60Hz
PoE Port
Port1~8
P
o
r
t
1
~
2
4
PoE Power on RJ45
port: Mode A 1/2(+),3/6(-)
PoE Power Output
Voltage: 55V DC Power: 32W(Max)
PoE Power Budget
120W
PoE Power total
130W
Temperature
Operating Temperature: -5°C ~ 50 °C (23 °F ~122°F )
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F )
Humidity
Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing