AERMEC MODUCONTROL User manual

SUMMARIZED USER MANUAL
WATER
CHILLER
MODUCONTROL
CHILLERS
REVERSIBLE HEAT PUMPS
CONDENSING UNITS
• EXTERNAL UNITS
• HIGH EFFICIENCY
• HOT WATER PRODUCTION
UP TO 50ºC
READINGMENU•USERMENU•ERRORMENU
EN

READINGS MENU
Reading menu
The reading menu gives the user the option to read all parameters
Lista indici e relative letture MENÚ LETTURE (nessuna password)
Index - String Meaning of the reading
Water output temperature
Water input temperature
Coil temperature
Force gas temperature
Outside air temperature
Delivery pressure
Suction pressure
Thermostat
CP times
Hours of operation (thousands)
Hours of operation (units)
Compressor pickup current
(thousands)
Index - String Meaning of the reading
Compressor pickup current (units)
Software release
Minor software releases
Setting currently in use
DCP pressure setting
Operating hours
COMPRESSOR 2 (thousands)
Operating hours
COMPRESSOR 2 (units)
Compressor pickup current
COMPRESSOR 2 (thousands)
Compressor pickup current
COMPRESSOR 2 (units)
Power fraction
Required frequency (INVERTER)
Pressure drop
Parameters only visible in heat pump models
Parameters only visible in models set for hot domestic
water production
Parameters only visible in the models with DCP installed
Parametes only visible in bicompressor models
Parameters only visible in the models with inverter
compressor

USER MENU
User menu
The user menu gives the user the option to change settings
1. press the srewdriver symbol
2. 000 apears
3. Press the srewdriver again
4. Use up and down keys to nd a setting
5. Press the screwdriver again (blinking of index nr)
6. Change the setting with up and down keys
7. Conrm with screwdriver
For Opticlimate set:
1 STF on 26°C
2 BNF on 1°C

-
- -
SF1: index (6) user menu;
SF2: index (8) user menu;
TF1: index (7) user menu;
TF2: index (9) user menu;
In cooling mode, the work setting is calculated au-
tomatically on the basis of the outside temperature,
following the logic highlighted in the diagram.
SC1: index (A) user menu;
SC2: index (C) user menu;
TC1: index (B) user menu;
TC2: index (d) user menu;
In heating mode, the work setting is calculated au-
tomatically on the basis of the outside temperature,
following the logic highlighted in the diagram.
USER MENU

-
-
USER MENU

-
-
rature (depending on the type of control set by parameter (0) in the installer menu) is less than the hot
Lista indici e relative letture MENÚ LETTURE (nessuna password)
Index - String Meaning of the reading
Water output temperature
Water input temperature
Coil temperature
Force gas temperature
Outside air temperature
Delivery pressure
Suction pressure
Thermostat
CP times
Hours of operation (thousands)
Hours of operation (units)
Compressor pickup current
(thousands)
Index - String Meaning of the reading
Compressor pickup current (units)
Software release
Minor software releases
Setting currently in use
DCP pressure setting
Operating hours
COMPRESSOR 2 (thousands)
Operating hours
COMPRESSOR 2 (units)
Compressor pickup current
COMPRESSOR 2 (thousands)
Compressor pickup current
COMPRESSOR 2 (units)
Power fraction
Required frequency (INVERTER)
Pressure drop
Parameters only visible in heat pump models
Parameters only visible in models set for hot domestic
water production
Parameters only visible in the models with DCP installed
Parametes only visible in bicompressor models
Parameters only visible in the models with inverter
compressor
USER MENU

ERROR MENU
Error
An error can be reset by switching the main power of the unit off for 5 seconds.
When there is air trapped inside the system E104 will appear. Bleed the system and switch the power off to reset.
After rst time operation E104 will appear several times until all air is out.
We advise to use automatic bleeders at the highest point of the water-system.
-
-
-
-
-

Notes
-
-
-
-
-
-
-
-
-
122
ERROR MENU

--
-
--
-
ERROR MENU