AETEK C11-082-32-120 User manual

- OR - - OR -
ConsoleNVRRouter / switch
1. Install the PoE switch in a ventilated and dry place that is free of electromagnetic source, vibration, moisture, and dust.
2. Make sure the ventilation openings on the switch are not blocked.
3. Use CAT5 or 6 UTP/STP cables.
4. AC input (100~240V/AC, 50~60Hz, 2.5A)
C11-082-32-120 PoE Switch
Quick Installation Guide
The C11-082-32-120 is a 8xFE PoE + 2xGbE Combo Ex PoE switch capable of feeding 15.4/30W (56V max. per port)
power to Power over Ethernet (PoE) devices.
IMPORTANT:
INTRODUCTION
LED DEFINITIONS
CONNECTION
* 1x PoE switch * 1x Quick Installation Guide
* 2x rack mount ears * 1x power cord (type by the shipped-to area)
PACKAGE CONTENTS
Rack-mounting
Connections
Use SFP, LC type transceiver with 100Mbps or 1Gbps transfer speed in Single mode (10km,30km,50km,80km) or Multi
mode (0.5m or 2km) or Bidi (10km,30km,50km,80km).
PWR Green ON Power is on and normal.
Green OFF Power is off.
LAN Green ON Ethernet port is connected.
Blinking Data is being transmitted and received.
Green OFF No connection.
GbE
9,10
Green ON Ethernet port is connected
Blinking Data is being transmitted and received
Green OFF No connection
PoE Orange ON Port is enabled and supplying power to connected device.
Blinking An abnormal state, such as overload status, has been detected in the switch.
Orange OFF Port has no active network cable connected, or it is not established a link to connected
device.

EXTENSIVE MODE DIP SWITCH
ST Mode: normal communication between port 1~10.
ST VLAN: 1-8 port can be isolated each other but 1-8 port can connect to 9~10 port after open VLAN to stop broadcast
Storm to increase forwarding rate of frame.
EX Mode: 1-8 port can be isolated each other but 1-8 port can connect to 9~10 port after open VLAN to stop broadcast
storm to increase forwarding rate of frame. The EX mode(Port 1 & 2), Up to 250m PoE distance allows you to expand
you network via Ethernet cable to where there is no power line or outlet but where you want to x device such as IP
Camera.
• EX mode reaches 802.3af(12.95W) camera up to 250m@10Mbps via EXPoE ports
• EX mode reaches 802.3at(24W) camera up to 200m@10Mbps via EXPoE ports
Restart the switch after changing the Extensive mode.
Power
250 meters (820 feet)
PowerData &
EXtensive Mode
802.3af PoE Camera
Power
200 meters (656 feet)
PowerData &
EXtensive Mode
802.3at PoE Camera
GROUNDING COLUMN
50/60Hz, 2.5A Max
Power Socket
Grounding Column
The switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting
Earth) cable of AC cord or with Ground Cable.
AETEK INC.
3F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:[phone]|W:www.aetektec.com|E:[email protected]
All specications are subject to change without noice.
Copyright © 2020 AETEK INC. All rights reserved.
*Effect factors
1.Must connect af PoE PD.
2.Poor cabling quality with insufcient copper.
3.IP camera’s networking design could not support 10Mbps@250m transmission.
**Suggestion
1.Checking the interoperability reaching 10Mbps@250m before physical deployment.
2.Adjust to “EX Mode OFF” reaching 10/100Mbps@100m if “EX Mode ON” is fail.