AETEK C62-050-30-A User manual

C62-050-30-A / C62-050-30-B
* 1x PoE switch * 1x Quick Installation Guide
PACKAGE CONTENTS
P/N: A625016600G
Quick Installation Guide
C62-050-30-A L2 PRO bt Ceiling PoE Switch
C62-050-30-B L2 PRO bt Ceiling PoE Switch
CONNECTION
C62-050-30-A / C62-050-30-B
Installation Steps
24V LED
SYS LED
DO LED
DI LED
PWR LED
Reset
LAN LED
12V LED
PoE LED
φ150mm
Recommend hole size
for mounting ceiling PoE switch
is φ150 mm.
Connect LAN cable to
ceiling PoE switch.
Connect 12V / 24V / DI / DO cable
to ceiling PoE switch.
LAN
φ150mm φ150mm
12V / 24V
DI / DO
Installed on the system ceiling
1. Attach the ceiling mount bracket to plasterboard, etc.
● It is recommended to add the fastening screw to the hole size of the ceiling, turn it with a screwdriver to install it.
The ceiling thickness that can be connected with the clamping bracket is from 5 to 45 mm.
● The recommended screw torque is 7kgf-cm±3.
● Install on the ceiling with sufficient strength.
● If you have to install it on rock wool ceiling and other weak ceiling panels, please provide enough reinforcement.
● The recommended ceiling opening size is φ150mm.
● The recommended minimum space (height) for ceiling switch installation is 140mm (For Installation and CAT5/6 cable routing.)
Step 1 Step 2 Step 3
Push up ceiling PoE switch to
the ceiling hole.
Use a flathead screwdriver to installing
Turn right to lock.
(Turn left release)
Attach cover to
ceiling PoE switch.
Step 4 Step 5 Step 6
DO
DI
24VDC Output
at PoE Output
bt PoE Output
GND
bt PoE Input
12VDC Output
140mm 140mm 140mm
45~50mm
PD Port

AETEK INC.
6F, No.192-1,Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan,R.O.C.
|T:[phone]|W:
www.aetektec.com|E:[email protected] Copyright © 2023 AETEK INC. All rights reserved.
IP Address 192.168.1.1
Subnet Mask 255.255.255.0
User name
DEFAULTS
Power Amber ON The Power LED lights up when the switch is connected to a power source.
SYS
12V
24V
DI
DO
Green ON The System is ready.
Amber ON Have output 12VDC power.
Amber ON Have output 24VDC power.
The DI is received single.
The Do is enable.
LED DEFINITIONS
LAN
PoE
Green ON
Green ON
Green ON
Port is enabled and link established.
Grren Blinking Port is transmitting and receiving data.
Amber ON Indicates the PoE powered device (PD) is connected and the port supplies power successfully.
Amber Off Indicates no powered device (PD) connected.
Task Press time Port Status LED Behavior
Restart 2 ~ 7 seconds All LEDs are OFF
Restore default 7 ~ 12 seconds All LEDs stay ON
Reset Button
Password
admin
admin
C62-050-30-B C62-050-30-A
C62-044-91-380
L2 PRO bt PoE Switch
After installing this product on the ceiling, install the included panel.
Pay attention to the installation direction, align the groove with the notch on the panel
and install it correctly.
●Remove the panel with a flat-head screwdriver.
PoE (Data + Power)
Wifi AP Camera
Network
Speaker
Sensor
Wifi AP Camera
Network
Speaker
Sensor