aFe Power Takeda 56-10005D User manual

®
advanced FLOW engineering
Instruction Manual P/N: 56-10005D / 56-10005R
Make: Hyundai Model: Elantra Sport Year: 2017-2020 Engine: L4-1.6L Turbo
Make: Hyundai Model: Elantra GT Sport Year: 2018 Engine: L4-1.6L Turbo
Make: Hyundai Model: Elantra GT N Line Year: 2019-2020 Engine: L4-1.6L Turbo
Make: Hyundai Model: Veloster Year: 2019-2020 Engine: L4-1.6L Turbo
Make: Kia Model: Forte GT Year: 2019-2020 Engine: L4-1.6L Turbo

®
Label Qty. Description Part Number
A1 1 Air Filter (Pro DRY S) 21-91108 (Grey Media)
A2 1 Air Filter (Pro 5R) 24-91108 (Blue Media)
B 1 Tube 05-5610005B1
C 1 Housing 05-5610005B2
D 1 Coupling, Silicone Reducer 05-01490
E 1 Clamp, #044 03-50019
F 2 Retainer Clips 03-50616
G 1 Clamp, #048 03-50007
H 1 Fitting 03-50615
I 1 Threadlocker 03-50162
J 1 Seal, Trim: 7/16" (25" inches) 05-00072
Installation will require the following tools:
8mm and 10mm socket, extension, ratchet, 16mm wrench, pliers and flat-head screwdriver.
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7185.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Disconnect the negative battery terminal before proceeding.
• Retain factory parts for future use.
Page 2
Retain factory parts for future use.
Emissions Disclaimer:
This product is not currently CARB exempt and is not available for purchase in California or for use on any
vehicle registered with the California Department of Motor Vehicles.

aFepower.com
Page 3
A1/A2
B
D
FC
F
G
I
H
J
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF
ADVANCED FLOW ENGINEERING, INC. ANY REPRODUCTION IN PART OR IN WHOLE WITHOUT
THE WRITTEN PERMISSION OF ADVANCED FLOW ENGINEERING, INC. IS PROHIBITED.
SHEET 1 OF 1
advanced FLOW engineering, inc.
P.O. BOX 1719
CORONA, CA 92878-1719
[phone] / [phone] FAX
A
ThreadLocker
"Drawn"
A
1:2
APPROVED
DRAWN
REV.
DWG. NO.
CAD FILE:
SIZE
SCALE:

®
Refer to Figure A for Steps 1-3
Step 1: Remove the engine cover by pulling upward on it.
Step 2: Using pliers, open the clamp securing the hose to the air intake tube, and then slide the clamp
away from the intake tube. This clamp will be re-used. Disconnect the rubber hose from the air
intake tube.
Step 3: Release the two clips securing the top of the airbox to the bottom of the airbox.
REMOVAL
Page 4
Figure A

Refer to Figure B for Steps 4-5
Step 4: Using pliers, open the clamp securing the small hose to the air intake tube toward the firewall.
Slide the clamp away from the tube and disconnect the small rubber hose from the intake tube.
The clamp will be re-used.
Step 5: Loosen the clamp at the turbo inlet using a 10mm socket and ratchet.
aFepower.com
Page 5
REMOVAL
Figure B

®
Refer to Figure C for Step 6
Step 6: Remove the top of the factory airbox and the tube as one piece from of the vehicle.
Page 6
Figure C
REMOVAL

Refer to Figure D for Steps 7-9
Step 7: Remove the two plastic rivets connecting the factory air inlet to the front of the car. Use a
flat-head screwdriver to press down on the center of the rivet to unlock, and then pull them out.
These plastic rivets will be replaced.
Step 8: With a 10mm socket, extension and ratchet, loosen the three bolts securing the factory
housing to the vehicle. These three bolts will be re-used during the installation of the Takeda
air intake system.
Step 9: Remove the bottom of the factory housing and air inlet as one piece out of the vehicle.
Figure D
aFepower.com
Page 7
REMOVAL

®
Page 8
®
Page
Refer to Figure E for Step 10
Step 10: Transfer the three mounting grommets and sleeves from the bottom of the factory housing
to the Takeda housing.
Figure E
INSTALL

Page 9 aFepower.comaFepower.com Page
Refer to Figure F for Step 11
Step 11: Install the provided seal trim around the top edges of the airbox.
Figure F
INSTALL

®
Page 10
®
Refer to Figure G for Steps 11-12
Step 11: Install the Takeda housing into the vehicle. Secure it with the three bolts removed at Step 7.
One of the bolts will be installed inside the housing.
Step 12: Secure the housing to the air inlet with the two provided christmas tree plastic rivets.
Figure G
INSTALL