aFe Power Momentum GT User manual

®
advanced FLOW engineering Momentum GT Cold Air Intake System
Instruction Manual P/N: 51-76006 / 54-76006 / 75-76006
Make: Toyota Model: Land Cruiser (LC200/J200) Year: 2008-2019 Engine: V8-5.7L
Make: Toyota Model: Land Cruiser (LC200/J200) Year: 2012-2019 Engine: V8-4.6L
Make: Lexus Model: LX 570 Year: 2012-2019 Engine: V8-5.7L

®
Label Qty. Description Part Number
A1 1 Air Filter (Pro DRY S) 21-91092
A2 1 Air Filter (Pro 5R) 24-91092
A3 1 Air Filter (Pro-GUARD 7) 72-91092
B 1 Tube 05-76006B1
C 1 Housing 05-76006B2
D 1 Plug, Urethane 05-01202
E 1 Coupling, Silicone Hump 05-01398
F 1 Clamp, T-bolt 03-50265
G 1 Seal Trim (26" inches) 05-00007
H 1 Clamp #052 03-50008
I 2 Screw, Torx: M4 03-50491
J 1 Fitting, Nipple, Brs Hose 03-50191
Installation will require the following tools:
10mm & 8mm nut drivers, pliers, T20 & T30 drivers, 10mm & 11mm deep socket & driver, flathead
screwdriver, phillips screwdriver and 7/16" wrench.
Note: Not legal for use in California. The use of this device in any on-road or off-road vehicles registered with
the California Dept of Motor Vehicles (DMV) is strictly prohibited.
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call technical support at 951-493-7100
or e-mail [e-mail].
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Disconnect both the negative battery terminal before proceeding.
Page 2
Retain factory parts for future use.

aFepower.com
Page 3
A1/A2/A3
C
B
D
E
F
I
H
G
J

®
Refer to Figure A for Step 1
Step 1: Lexus Only: Remove the 7 clips 1 holding down the side cover 2 by pushing down on the
center of the clip to disengage them. Remove the side cover 2 .
REMOVAL
Page 4
Figure A
1
2
1
1
1
1
1
1

Refer to Figure B for Step 2
Step 2: Disconnect the MAF sensor 3 . Using a flat blade screwdriver, unclip the wire loom 4 from the
air box.
aFepower.com
Page 5
Figure B
REMOVAL
4
3

®
Refer to Figure C for Step 3
Step 3: Using a 10mm nut driver, loosen the clamp 5 at the air box. Unsnap the 4 clips 6 holding down
the air box lid. Remove the lid and the air filter.
Figure C
Page 6
REMOVAL
5
6
6
6
6

Refer to Figure D for Step 4
Step 4: Using a 10mm nut driver, remove the 3 screws 7 holding the lower section of the air box.
Remove the air box.
Figure D
aFepower.com
Page 7
7
REMOVAL
7
7

®
Page 8
Refer to Figure E for Step 5
Step 5: Using a 10mm nut driver, remove the 2 screws 8 and the air inlet 9 .
Figure E
REMOVAL
9
8
8

Refer to Figure F for Step 6
Step 6: Remove the engine cover 10 by pulling up and then out. Set the engine cover aside.
Page 9
Figure F
REMOVAL
10
aFepower.com

Refer to Figure G for Step 7
Step 7: Remove the vacuum hose 11 and breather hose 12 from the intake tube.
Page 10
Figure G
®
12
11
REMOVAL