Agilent Technologies InfiniiVision 4000 X Series User manual

s1
Agilent InfiniiVision
4000 X-Series
Oscilloscopes
User's Guide

2 Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide
Notices
© Agilent Technologies, Inc. 2005-2013
No part of this manual may be reproduced in
any form or by any means (including elec-
tronic storage and retrieval or translation
into a foreign language) without prior agree-
ment and written consent from Agilent
Technologies, Inc. as governed by United
States and international copyright laws.
Manual Part Number
54709-97026
Edition
Third edition, September 2013
Printed in Malaysia
Agilent Technologies, Inc.
1900 Garden of the Gods Road
Colorado Springs, CO 80907 USA
Warranty
The material contained in this docu-
ment is provided “as is,” and is sub-
ject to being changed, without notice,
in future editions. Further, to the max-
imum extent permitted by applicable
law, Agilent disclaims all warranties,
either express or implied, with regard
to this manual and any information
contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a par-
ticular purpose. Agilent shall not be
liable for errors or for incidental or
consequential damages in connec-
tion with the furnishing, use, or per-
formance of this document or of any
information contained herein. Should
Agilent and the user have a separate
written agreement with warranty
terms covering the material in this
document that conflict with these
terms, the warranty terms in the sep-
arate agreement shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a license
and may be used or copied only in accor-
dance with the terms of such license.
Restricted Rights Legend
If software is for use in the performance of a
U.S. Government prime contract or subcon-
tract, Software is delivered and licensed as
“Commercial computer software” as
defined in DFAR 252.227-7014 (June 1995),
or as a “commercial item” as defined in FAR
2.101(a) or as “Restricted computer soft-
ware” as defined in FAR 52.227-19 (June
1987) or any equivalent agency regulation or
contract clause. Use, duplication or disclo-
sure of Software is subject to Agilent Tech-
nologies’ standard commercial license
terms, and non-DOD Departments and
Agencies of the U.S. Government will
receive no greater than Restricted Rights as
defined in FAR 52.227-19(c)(1-2) (June
1987). U.S. Government users will receive
no greater than Limited Rights as defined in
FAR 52.227-14 (June 1987) or DFAR
252.227-7015 (b)(2) (November 1995), as
applicable in any technical data.
Safety Notices
CAUTION
A CAUTION notice denotes a haz-
ard. It calls attention to an operat-
ing procedure, practice, or the like
that, if not correctly performed or
adhered to, could result in damage
to the product or loss of important
data. Do not proceed beyond a
CAUTION notice until the indicated
conditions are fully understood and
met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly per-
formed or adhered to, could result
in personal injury or death. Do not
proceed beyond a WARNING
notice until the indicated condi-
tions are fully understood and
met.
Print History
54709-97000, October 2012
54709-97014, February 2013
54709-97026, September 2013
Trademarks
Java is a U.S. trademark of Sun Microsys-
tems, Inc.
Sun, Sun Microsystems, and the Sun Logo
are trademarks or registered trademarks of
Sun Microsystems, Inc. in the U.S. and other
countries.

Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide 3
InfiniiVision 4000 X-Series Oscilloscopes—At a Glance
Table 1 4000 X-Series Model Numbers, Bandwidths, Sample Rates
Bandwidth 200 MHz 350 MHz 500 MHz 1 GHz 1.5 GHz
Sample Rate
(interleaved,
non-interleaved)
5GSa/s,
2.5 GSa/s
5GSa/s,
2.5 GSa/s
5GSa/s,
2.5 GSa/s
5GSa/s,
2.5 GSa/s
5GSa/s,
2.5 GSa/s
2-Channel + 16 Logic
Channels MSO
MSO-X 4022A MSO-X 4032A MSO-X 4052A
4-Channel + 16 Logic
Channels MSO
MSO-X 4024A MSO-X 4034A MSO-X 4054A MSO-X 4104A MSO-X 4154A
2-Channel DSO DSO-X 4022A DSO-X 4032A DSO-X 4052A
4-Channel DSO DSO-X 4024A DSO-X 4034A DSO-X 4054A DSO-X 4104A DSO-X 4154A

4 Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide
The Agilent InfiniiVision 4000 X- Series oscilloscopes deliver these features:
• 200 MHz, 350 MHz, 500 MHz, 1 GHz, and 1.5 GHz bandwidth models.
• 2- and 4- channel digital storage oscilloscope (DSO) models.
• 2+16- channel and 4+16- channel mixed- signal oscilloscope (MSO)
models.
An MSO lets you debug your mixed- signal designs using analog signals
and tightly correlated digital signals simultaneously. The 16 digital
channels have a 1.25 GSa/s sample rate, with a 250 MHz toggle rate.
• 12.1 inch SVGA touchscreen display. The touchscreen makes the
oscilloscope easier to use:
•You can "touch" inside alpha- numeric keypad dialogs to enter file,
label, network, and printer names, etc., instead of using softkeys and
the Entry knob.
•You can drag a finger across the screen to draw rectangular boxes
for zooming in on waveforms or setting up Zone triggers.
•You can touch the blue menu icon in the sidebar to display
information or control dialogs. You can drag (undock) these dialogs
out of the sidebar, for example, to view cursor values and
measurements at the same time.
•You can touch other areas of the screen as substitutes for using
front panel keys, softkeys, and knobs.
• Interleaved 4 Mpts or non-interleaved 2 Mpts MegaZoom IV memory
for the fastest waveform update rates, uncompromised.
• All knobs are pushable for making quick selections.
• Trigger types: edge, edge then edge, pulse width, pattern, OR, rise/fall
time, Nth edge burst, runt, setup & hold, video, and zone.
• Serial decode/trigger options for: CAN/LIN, FlexRay, I2C/SPI, I2S,
UART/RS232, MIL- STD- 1553/ARINC 429, and USB. There is a Lister
for displaying serial decode packets.
• Math waveforms: add, subtract, multiply, divide, FFT, d/dt, integrate,
square root, Ax+B, square, absolute value, common logarithm, natural
logarithm, exponential, base 10 exponential, low pass filter, high pass
filter, averaged value, magnify, measurement trend, chart logic bus
timing, and chart logic bus state.

Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide 5
• Reference waveform locations (4) for comparing with other channel or
math waveforms.
• Many built- in measurements and a measurement statistics display.
• Built- in, license- enabled 2- channel waveform generator with: arbitrary,
sine, square, ramp, pulse, DC, noise, sine cardinal, exponential rise,
exponential fall, cardiac, and Gaussian pulse. Modulated waveforms on
WaveGen1 except for arbitrary, pulse, DC, and noise waveforms.
• USB and LAN ports make printing, saving, and sharing data easy.
• VGA port for displaying the screen on a different monitor.
• A Quick Help system is built into the oscilloscope. Press and hold any
key to display Quick Help. Complete instructions for using the quick
help system are given in “Access the Built-In Quick Help" on page 62.
For more information about InfiniiVision oscilloscopes, see:
"www.agilent.com/find/scope"

6 Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide
In This Guide
This guide shows how to use the InfiniiVision 4000 X-Series oscilloscopes.
When unpacking and using the
oscilloscope for the first time, see:
•Chapter 1, “Getting Started,” starting on page 27
When displaying waveforms and
acquired data, see:
•Chapter 2, “Horizontal Controls,” starting on page 65
•Chapter 3, “Vertical Controls,” starting on page 81
•Chapter 4, “Math Waveforms,” starting on page 91
•Chapter 5, “Reference Waveforms,” starting on page
121
•Chapter 6, “Digital Channels,” starting on page 125
•Chapter 7, “Serial Decode,” starting on page 145
•Chapter 8, “Display Settings,” starting on page 151
•Chapter 9, “Labels,” starting on page 159
When setting up triggers or changing
how data is acquired, see:
•Chapter 10, “Triggers,” starting on page 167
•Chapter 11, “Trigger Mode/Coupling,” starting on
page 205
•Chapter 12, “Acquisition Control,” starting on page 213
Making measurements and analyzing
data:
•Chapter 13, “Cursors,” starting on page 231
•Chapter 14, “Measurements,” starting on page 241
•Chapter 15, “Mask Testing,” starting on page 271
•Chapter 16, “Digital Voltmeter,” starting on page 283
When using the built-in license
enabled waveform generator, see:
•Chapter 17, “Waveform Generator,” starting on page
287
When saving, recalling, or printing,
see:
•Chapter 18, “Save/Email/Recall (Setups, Screens,
Data),” starting on page 309
•Chapter 19, “Print (Screens),” starting on page 323
When using the oscilloscope's utility
functions or web interface, see:
•Chapter 20, “Utility Settings,” starting on page 329
•Chapter 21, “Web Interface,” starting on page 349

Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide 7
For reference information, see: •Chapter 22, “Reference,” starting on page 367
When using licensed serial bus
triggering and decode features, see:
•Chapter 23, “CAN/LIN Triggering and Serial Decode,”
starting on page 387
•Chapter 24, “FlexRay Triggering and Serial Decode,”
starting on page 405
•Chapter 25, “I2C/SPI Triggering and Serial Decode,”
starting on page 415
•Chapter 26, “I2S Triggering and Serial Decode,”
starting on page 435
•Chapter 27, “MIL-STD-1553/ARINC 429 Triggering and
Serial Decode,” starting on page 445
•Chapter 28, “UART/RS232 Triggering and Serial
Decode,” starting on page 461
•Chapter 29, “USB 2.0 Triggering and Serial Decode,”
starting on page 471
TIP
Abbreviated instructions for pressing a series of keys and softkeys
Instructions for pressing a series of keys are written in an abbreviated manner. Instructions
for pressing [Key1], then pressing Softkey2, then pressing Softkey3 are abbreviated as
follows:
Press [Key1] > Softkey2 > Softkey3.
The keys may be a front panel [Key] or a Softkey. Softkeys are the six keys located directly
below the oscilloscope display.

8 Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide

Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide 9
Contents
InfiniiVision 4000 X-Series Oscilloscopes—At a Glance 3
In This Guide 6
1 Getting Started
Inspect the Package Contents 27
Attaching the Accessory Pouch 30
Tilt the Oscilloscope for Easy Viewing 31
Power-On the Oscilloscope 32
Connect Probes to the Oscilloscope 33
Maximum input voltage at analog inputs 34
Do not float the oscilloscope chassis 34
Input a Waveform 34
Recall the Default Oscilloscope Setup 35
Use Auto Scale 35
Compensate Passive Probes 37
Learn the Front Panel Controls and Connectors 38
Front Panel Overlays for Different Languages 45
Learn the Touchscreen Controls 47
Draw Rectangles for Waveform Zoom or Zone Trigger Set
Up 47
Drag Waveforms Left and Right to Change the Horizontal
Position 48

10 Agilent InfiniiVision 4000 X-Series Oscilloscopes User's Guide
Select Sidebar Information or Controls 49
Undock Sidebar Dialogs by Dragging 50
Select Dialog Menus and Close Dialogs 51
Drag Cursors 51
Touch Softkeys and Menus On the Screen 51
Enter Names Using Alpha-Numeric Keypad Dialogs 52
Change Waveform Offsets By Dragging Ground Reference
Icons 53
Access Controls and Menus Via the Spark Icon 54
Turn Channels On/Off and Open Scale/Offset Dialogs 56
Access the Horizontal Menu and Open the Scale/Delay
Dialog 56
Access the Trigger Menu, Change the Trigger Mode, and Open
the Trigger Level Dialog 57
Use a USB Mouse and/or Keyboard for Touchscreen
Controls 58
Learn the Rear Panel Connectors 58
Learn the Oscilloscope Display 60
Access the Built-In Quick Help 62
2 Horizontal Controls
To adjust the horizontal (time/div) scale 67
To adjust the horizontal delay (position) 67
Panning and Zooming Single or Stopped Acquisitions 68
To change the horizontal time mode (Normal, XY, or Roll) 69
XY Time Mode 70
To display the zoomed time base 73
To change the horizontal scale knob's coarse/fine adjustment
setting 75
To position the time reference (left, center, right) 75