Aircraft PowerScrub User manual

POWERSCRUB
User Guide

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
2

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
3
Welcome
Thank you for purchasing this AirCraft POWERSCRUB
Please read all instructions, and the following important Safety
Advice, before use:
• This appliance is for domestic, indoor use only.
• POWERSCRUB is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless supervised or instructed by a
person responsible for their safety.
• Do not expose the electronics of your POWERSCRUB, or attempt to
service the Battery. There are no user serviceable parts inside. Refer
servicing to qualified service agents only. Attempting self-service will
invalidate your guarantee.
• Please ensure voltage rating for the Charging Adaptor matches your
outlet voltage.
• Before using, remove any items that could become entangled in the
rotating head, such as clothing, loose papers, cords, cables, and any
fragile objects.
• Do not use to clean volatile liquids such as petrol or white spirit.
• Only use the Charging Adaptor supplied, or an original replacement.
Visit AirCraftVacuums.com for original replacement parts.
• Do not handle the Charging Adaptor plug or power cable with wet
hands.
• If appliance is not working as intended, please do not continue to
operate or charge, and refer to an authorised service agent.
• Disconnect from the Charger before commencing use, and before
cleaning or maintaining.
• Operate in room temperature environments only.
• Do not submerge whole unit in water or any other liquid.
• Do not touch the rotating disc during operation.
• Always apply a Brush head or Pad to the rotating disc before use.
• Avoid operating continuously for over 20 minutes as this may cause
overheating.
• For technical assistance, please contact us via
[email protected].

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
4
POWERSCRUB

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
5
Getting Started
Inside the box with your POWERSCRUB you will find:
• 3 Brush heads: 1 x Flat; 1 x Round; 1 x Pointed
• Pad holder
• Grey microfibre Pad
• Sponge Pad
• Extension handle
• Hook attachment
• Charging adaptor
• Storage base/stand
• Stainless steel storage rack
Assembly
Before starting, ensure your POWERSCRUB is fully charged
using the original AC Charging Adaptor.
POWERSCRUB has an optional handle
extension for those harder-to-reach spots,
and for comfortable floor cleaning. Please
insert either the hook attachment or the
handle extension into the top of the
POWERSCRUB as required.
To assemble the stand, insert the stainless
steel storage rack into the corresponding
holes on the stand – you may choose either
side. You may now neatly store your
POWERSCRUB,brush heads and the
handle extension (or hook attachment)
together in the stand.

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
6
Using your POWERSCRUB
1. Select an attachment. To use one of the 3 brush heads (Round, Flat
or Pointed), insert the rotating triangular shaft at the tip of the
POWERSCRUB into the corresponding opening in the centre of the
Brush head, and twist clockwise. To remove, simply twist in an
anticlockwise direction and detach.
2. To use the grey microfibre Pad or the sponge Pad, simply attached to
the pad holder using Velcro, and attach the Pad holder to the
POWERSCRUB as above. Please ensure that the Pad is placed
centrally on the Pad holder.
3. You may choose to use your POWERSCRUB with or without the
handle extension installed. To install, simply click into place. To
remove, press the Handle release button, and pull to detach.
4. You may also choose to moisten surfaces using a spray bottle
containing water or cleaning solution, before going over with your
POWERSCRUB.
5. Adjust the hinge to your preferred angle.
6. Press the
Start/Stop
button. The LED light on the handle will illuminate
green and the Brush head/Pad will start to rotate at 180rpm. Press
again to switch to high-speed mode (250rpm) – the Speed Indicator
light will now turn red. To turn off, press the
Start/Stop
button once
again. You may also hold down the button for 3 seconds when in low
speed mode to switch off.
7. You may submerge the rotation shaft (the section below the hinge) of
your POWERSCRUB in water for short periods. Do not allow the
section above the hinge to become submerged in water.

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
7
Charging
Use
only
the original Charging Adaptor supplied with your
POWERSCRUB.
The battery charge level is indicated in real time on the numerical
LED display on the handle:
Please recharge when the battery level indicator shows a low level of
power, by connecting the Charging Adaptor to a power supply and
to the charging port on the base, as shown above. Please insert the
rubber cover into the charging port when not being charged.
Charge time is approximately 2.5 hours. Disconnect the Charging
Adaptor once fully charged (when the battery level indicator displays
100). Overcharging may damage the built-in battery.
Important
: Use only the original AirCraft AC Charging Adaptor
supplied, or an original replacement from an authorized AirCraft
retailer. Using any other type of Charging Adaptor will not charge the
battery, and may damage the battery and invalidate your guarantee.

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
8
Storage and Maintenance
It is recommended that your POWERSCRUB is regularly cleaned and
maintained to ensure optimal performance.
You may clean the exterior of your POWERSCRUB using a soft, dry
cloth.
The microfibre Pad may be machine-washed (at 30º, without bleach
or fabric softener) or hand-washed as often as required. Do not dry
clean or iron. Brush heads and the sponge Pad should be rinsed with
clean water after each use and may be left to dry on the storage rack.
Do not store where there is a danger of freezing. Freezing may
damage internal components and may void your guarantee.
Store with at least at 60% charge to prolong the lifespan of the
battery. Charge at least every 6 months to maintain the battery.
Additional or replacement POWERSCRUB accessories are available
at AirCraftVacuums.com.

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
9

!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
10
Technical Specifications
• Voltage: 7.4 v
• Power: 84 w
• Battery: Lithium 2000mAh (14.8 Wh)
• Adaptor output voltage: DC 12 v / 1 A
• Charge Time: 2.5 hrs
• Operating Time: 40 mins
• Dimensions: 120 x 6.5 x 6.5 cm
• Net Weight: 1.08 kg
• Noise level: < 70 dB