Airflow 7106A User manual

Warranty and Installation Instructions
MaxAir Wall Exhaust Fan
7106A7106A
7106A7106A
7106A
7108A7108A
7108A7108A
7108A

1. Check that the proposed location of the fan will
not foul joists, existing wiring or other internal
wall features (wall thickness between 110
and 310mm). Use template provided to mark
out hole.Cut a hole through the wall ø230mm.
Screw fan assembly to internal wall via 4
corner openings, see fig. A. (Appropriate
fasteners to be used for each installation
not provided.)
2. Remove Termination Cover see fig B (screws
marked with “1”, “2”, “3”). 4. With fan assembly mounted on the internal
wall, cut PVC sheet to suit wall depth.
7106A connection diagram
7108A connection diagram
1
2
3
Fig A
FAN
ASSEMBLY
2
3. Electrician to make electrical connections as
shown, using 3 core, 1mm2cable. Replace
Termination Cover.
Fig B
Fig B

5. Coil the cut PVC sheet around Wall
Grille Outlet spigot and slide into
retaining clips.
6. Screw Wall Grille Outlet to external wall.
(Appropriate fasteners to be used for
each installation not provided.)
7. Place Cover assembly as shown over fan
assembly and tighten retaining screw.
Test. Ready to go.
WARNING:
The appliance is not intended for use by children
or infirm persons without supervision.
Children should be supervised to ensure they do
not play with the appliance.
Appliance intended to be mounted on external
wall only.
HOLE CUTOUT TEMPLATE
HOLE CENTRE ø230mm

WARRANTY
The benefits conferred by this warranty are in addition to all other rights and remedies in respect of
the product which the consumer has under the Trade Practices Act and similar State and Territory laws.
The origional purchaser of this Airflow Ducted Fan Kit is provided with the following warranty,
subject to the following conditions. Gerard Industries Pty Ltd warrant this product for a period of 3
years from the date of purchase for all parts defective in workmanship or materials. All defective
parts will be replaced free of charge.The following exclusions do not preclude the purchaser from
those statutory rights consumers have under the Trade Practices Act or similar State and Territory Laws.
WARRANTY CONDITIONS
1. This warranty is only valid for appliances installed according to the manufacturer’s instructions.
2. This appliance must not be modified or changed in any way.
3. All wiring must be carried out by a licensed electrician or similarly qualified person and must be
connected to the voltage requirements as specified in the ratings label.
4. The manufacturer does not accept liability for any direct or consequential damage, loss or
other expense arising from misuse or incorrect installation and operation of the appliance.
5. Warranty will only be given on appliances where proof of purchase date is provided eg.original
invoice or copy.
As a record of your purchase, please fill out the following details and file this information with your
purchase invoice.
Products of Gerard Industries Pty Ltd ABN 27 007 873 529
12 Park Terrace, Bowden SA 5007
Telephone [phone] Facsimile [phone]
clipsal.com
F1698/01
 Copyright 2000
Launceston D.H. & L.S. Chilcott Pty Ltd
89 Olive Street
Launceston 7250
Phone [phone]
WA Electric Spares & Service
Unit 2/12 Buckingham Drive
Wangara 6065
Phone [phone]
NT G &T Electrical Enterprises Pty Ltd
Unit 4/4 College Road
Berrimah 0828
Phone [phone]
NZ Clipsal Industries (NZ) Ltd
PO Box 51317
Pakuranga, Auckland, New Zealand
47 Ben Lomond Crescent
Pakuranga, Auckland, New Zealand
Phone [phone]
SERVICE CENTRES
NSW Southside Elements
752 Old Princes Highway
Sutherland 2232
Phone [phone]
VIC W.A.M. (Wiring & Maintenance)
1126 Whitehorse Road
Box Hill 3128
Phone [phone]
QLD Universal Electrical Services
9 Horizon Drive
Beenleigh 4207
Phone [phone]
SA Ivesons Electrical
417 South Road
Keswick 5035
Phone [phone]
TAS/Hobart F.J. Booth Appliance Repairs
14 Patrick Street
Hobart 7000
Phone [phone]
Airflow Model Number
Serial Number
Purchased From
Date of Purchase