AirLive IG-641BT-1.25G User manual

Aug. 10, 2021
Ver. 1.0
IG-641BT-1.25G
User Manual

Copyright & Disclaimer
No part of this publication may be reproduced in any form or by any means, whether
electronic, mechanical, photocopying, or recording without the written consent of AirLive
Technology Corp.
AirLive Technology Corp has made the best effort to ensure the accuracy of the information
in this user’s guide. However, we are not liable for the inaccuracies or errors in this guide.
Please use with caution. All information is subject to change without notice
All Trademarks are properties of their respective holders.
Disposal
For more detailed specifications please see the datasheet.
The datasheet can been found online on www.airlive.com
** Specifications are subject to change and improvement without notice.
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this
product for environmentally safe recycling.

Table of Contents
1. Overview................................................................................................... 4
1.1 Power On Switch ............................................................................... 5
1.2 Switch Connections ........................................................................... 6

1
1. Overview
6-Port Gigabit PoE Switch with VLAN and 90W 802.3bt High PoE port
Compliant with the latest PoE technology 802.3bt/at/af, the AirLive IG-641BT-1.25G Gigabit
switch supports high power, port 1 up to 90W (802.3bt), and Port 2~4 up to 30W/each
(802.3at), with 1 SFP port and 1 Gigabit PD Uplink port which can receive up to 60W PoE
Power and power on the switch. The switch automatically detects and adaptively supplies
needed power to connected PoE devices; for non-PoE devices, it will just transfer data
intelligently.
For the application where management is not really needed but VLAN is useful and budget
is controlled, the AirLive IG-641BT can help. Using a smart DIP-switch to turn the IG-641BT
VLAN feature and PoE Watch dog on. Moreover Port 4 can support data and power up to
250meter at 10Mbps over Cat.5e cable that help where a PD is installed far away, and a
power source is hard to get.

1.1 Power On Switch
Power On the IG-641BT-1.25G Switch.
The Switch can be powered by the Standard 4 Pin Terminal block or also via Port 5 (Uplink)
of the Switch with a max of 60W PoE.
Input Voltage: DC48~55V
Input Type: 4 Pin Terminal (block V1+V1- V2+ V1-) Supports Dual Power Input
PoE Input: Uplink Gigabit port (port 5) supports PoE power Supply, which can receive
power up to 60W.

1.2 Switch Connections
AirLive IGM-642BT-2.5G Industrial switch supports the high-power output PoE++ at 90W for Port 1.
This higher output allows it to power more device then just an IP camera or Access point. The 90W
PoE can be used to power on high power needed PoE Systems, Digital Signage or even PoE LED
lighting and much more.
Ports 2 ~3 have a maxium output of 30W.
DIP Switch Control
VLAN: Port isolation mode. In this mode PoE Ports (1~4) cannot communicate with each other and
can only communicate with the UP-Link port, Also the PoE Watch Dog function is Enabled. DIP
Switch LED will be buring Solid Green.
Default: Normal mode, Normal communication with each port. The transmission distance is up to
100meter. PoE Watch Dog function not available. DIP Switch LED is Off.
Extend: Link extension mode, (Port 4) PoE power supply and data transmission distance can be
extended to 250 meter at the transmission rate 10Mbps. Also, the PoE Watch Dog function is
Enabled. DIP Switch LED will be flashing Green.
LED Indicator Definition State Description
PWR (Red) Power Indicator Lighting Powered
Un-Light No Power
Link (Green) Port Indicator Lighting Connecting
Flash Data Transmition
Un-light Disconnect
PD (Green) Power receiving Indicator Lighting Receiving power
Un-light No Receiving power
Mode (Green) DIP Indicator Lighting VLAN
Un-light Default
Flash Extend
PoE (Yellow) PoE Indicator Lighting PoE Powered
Un-light No Power