Airspan AirHarmony 4000 DC User manual

AirHarmony-4000 DC Installation Guide
Integrated External Duplexers
Part Number: UGD-D01123
System Release: 15.0
Revision: A
Published: August 2016

© Copyright by Airspan Networks Ltd., 2016-2016. All rights reserved worldwide.
Legal Notices
The information contained within this document is proprietary, privileged and intended only for the recipient. As such, the
information is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any
specific agreements protecting Airspan Networks Ltd. rights in the aforesaid information. Neither this document nor the
information contained herein may be published, reproduced, transmitted or disclosed to third parties, in whole or in part,
without the express, prior, written permission of Airspan Networks Ltd. In addition, any use of this document or the
information contained herein for the purposes other than those for which it is disclosed is strictly forbidden.
Airspan Networks Ltd. reserves the right, without prior notice or liability, to make changes in equipment design or
specifications.
Information supplied by Airspan Networks Ltd. is believed in good faith to be accurate and reliable, while every care has
been taken in preparing these documents. However, Airspan Networks Ltd. does not make any representations and gives
no warranties of whatever nature in respect of these documents, including without limitation, the accuracy or
completeness of any information, facts and/or opinions contained therein. No responsibility is assumed by Airspan
Networks Ltd. for the use of the documents nor for the rights of third parties which may be effected in any way by the use
thereof. The provision of these documents (and the documents themselves) does not constitute professional advice of any
kind. Any representation(s) in these documents concerning performance of Airspan Networks Ltd. product(s) are for
informational purposes only and are not warranties of future performance, either expressed or implied. Airspan Networks
Ltd., its affiliates, directors, employees and agents shall not be held liable for any damages or losses, of any nature
whatsoever, arising from any use of and/or reliance on the documents.
These documents may contain flaws, omissions or typesetting errors; no warranty is granted nor liability assumed in
relation thereto unless specifically undertaken in Airspan Networks Ltd. sales contract or order confirmation. Information
contained herein is periodically updated and changes will be incorporated into subsequent editions. If you have
encountered an error, please notify Airspan Networks Ltd.
Product performance figures quoted within this document are indicative and for information purposes only.
UK WEEE Registration number: WEEE/AB0207WZ. For more information, see WEEE Information for Airspan
Customers and Recyclers.
Acknowledgements
© Intel Corporation http://www.intel.com/
© Microsoft Corporation http://www.microsoft.com

UGD-D01080 Airspan Commercial and Internal Use i
Table of Contents
Document Information ......................................................................................1
Abstract .................................................................................................................................1
Revision History.....................................................................................................................1
Warnings and Cautions ......................................................................................2
Human Exposure to Radio Frequencies ................................................................................2
Radio Interference ................................................................................................................2
Modifications ........................................................................................................................2
General..................................................................................................................................2
Important Safety Instructions .........................................................................................3
Safety.....................................................................................................................................3
Warning of Hazardous Voltages............................................................................................3
Adherence to European Directive 1999/5/EC.......................................................................4
Warning Symbols ..................................................................................................................4
Service Information...............................................................................................................4
UL Information ......................................................................................................................5
Lightning Protection..............................................................................................................5
Outdoor Ethernet Cabling .....................................................................................................5
DECLARATION OF CONFORMITY ...........................................................................................6
GPS Compliance ....................................................................................................................7
Maximum Output TX Total Power......................................................................7
Power Consumption –Supply and Current...........................................................................8
Antenna System ....................................................................................................................9
External Antenna...................................................................................................................9
About This Document ......................................................................................10
Purpose ...............................................................................................................................10
Intended Audience..............................................................................................................10
Document Conventions.......................................................................................................10

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use ii
Document Organization ......................................................................................................12
Related Reading ..................................................................................................................12
Customer Care Help Desk ................................................................................13
Airspan Encourages Comments ..........................................................................................13
1Introduction.................................................................................................14
1.1 AirHarmony-4000 ........................................................................................................14
1.2 Deployment .................................................................................................................14
1.3 Related AirHarmony 4000 DC INT EXT Variants ..........................................................16
2Getting Started ............................................................................................17
2.1 Workflow of Installation ..............................................................................................17
2.2 AirHarmony-4000 DC INT EXT Installation Checklist ...................................................18
3Verifying Prerequisites.................................................................................18
3.1 Verifying Site Requirements ........................................................................................18
3.2 Verify Installation Requirements.................................................................................18
3.2.1 Verify the Tools ...........................................................................................................18
3.2.2 Verify the Parts and Kits..............................................................................................19
3.2.3 Power Supply and Current .......................................................................................... 20
3.2.4 Panels ..........................................................................................................................22
3.2.5 Physical Dimensions ....................................................................................................23
3.2.6 Environmental .............................................................................................................23
4Installing AirHarmony-4000 DC INT EXT .......................................................25
4.1 Connecting the GPS Antenna ......................................................................................25
4.2 Pole/Wall Mount Assembly .........................................................................................25
4.2.1 Mounting on a Wooden Pole ......................................................................................26
4.2.2 Mounting on a Non-Wooden Pole .............................................................................. 28
4.2.3 Mounting on a Wall..................................................................................................... 29
4.3 Securing AirHarmony-4000 to the Mounting Plate.....................................................31
5AirHarmony-4000 DC INT EXT Connections..................................................35
5.1 Grounding ....................................................................................................................35

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use iii
5.2 Remote Antenna Assembly .........................................................................................35
5.2.1 Connecting RF Jumper Cables to External Antenna.................................................... 35
5.2.2 Weather-proofing the Antenna Connections ............................................................. 36
5.3 Cable Connections .......................................................................................................36
5.3.1 Copper Ethernet Cable Assembly................................................................................36
Hardware Requirements ........................................................................................................36
Assembly Instructions.............................................................................................................36
5.4 Fiber Ethernet (SFP) Cable Installation........................................................................37
5.4.1 SFP Cable Connection..................................................................................................38
5.5 Connecting the DC Power Cable to AirHarmony-4000 DC INT EXT.............................39
5.5.1 Connecting the DC Power Cable to AirHarmony.........................................................40
5.5.2 AC/DC Power Converter –Optional............................................................................ 41
AJob Sheet .....................................................................................................42
BAbbreviations...............................................................................................43
Figures
Figure 1: AirHarmony-4000 DC INT EXT with Integrated External Duplexers.........................................9
Figure 2: AirHarmony-4000 DC INT EXT................................................................................................ 15
Figure 3: Workflow................................................................................................................................17
Figure 4: AirHarmony-4000 DC INT EXT Unit, Bottom panel ................................................................ 22
Figure 5: AirHarmony-4000 DC INT EXT Unit, Top panel ......................................................................23
Figure 6: Attaching GPS antenna to unit............................................................................................... 25
Figure 7: Pole/Wall mounting plate......................................................................................................26
Figure 8: Mounting plate on pole ......................................................................................................... 27
Figure 9: Through-bolt & Mounting plate............................................................................................. 28
Figure 10: Pole/Wall mounting plate (w/o bolt)................................................................................... 28
Figure 11: Mounting plate mounted.....................................................................................................29
Figure 12: Mounting Plate on Wall .......................................................................................................30
Figure 13: Lift unit and fit the slotted holes unto studs on top of mounting plate..............................31
Figure 14: Align Pins..............................................................................................................................31
Figure 15: AirHarmony mounted on Wooden Pole ..............................................................................32
Figure 16: AirHarmony mounted on Concrete Pole .............................................................................33
Figure 17: AirHarmony being mounted on a Wall ................................................................................ 34
Figure 18: Grounding ............................................................................................................................35
Figure 19: Gland connector - copper ....................................................................................................36
Figure 20: Ethernet Cable through connector ...................................................................................... 37
Figure 21: LC duplex cable assembly ....................................................................................................38

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use iv
Figure 22: Cable connector hook up to the board connector .............................................................. 38
Figure 23: Slide on inner housing.......................................................................................................... 39
Figure 24: Slide over and click...............................................................................................................39
Figure 35: attaching power cable to AirHarmony.................................................................................40
Figure 36: Optional AC/DC Converter...................................................................................................41
Tables
Table 1: AirHarmony--4000 DC INT EXT FCC Maximum Output TX Total Power....................................7
Table 2: AirHarmony-4000 DC INT EXT ETSI Maximum Output TX Total Power ....................................7
Table 3: Power Consumption.................................................................................................................. 8
Table 4: Typographic Conventions........................................................................................................ 10
Table 5. AirHarmony 4000 DC Integrated External Duplexers Variants ...............................................16
Table 6. Minimum Hardware Requirements ........................................................................................18
Table 7. Parts & Kits ..............................................................................................................................19
Table 8. Amperage Draw.......................................................................................................................21
Table 9: AirHarmony-4000 Physical Dimensions ..................................................................................23
Table 10: AirHarmony-4000 Environment Compliance ........................................................................24
Table 11: Cable Hardware..................................................................................................................... 36
Table 12: AC/DO Converter Specifications ...........................................................................................41
Table 13: Job Sheet ...............................................................................................................................42

AirHarmony-4000 (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 1
Document Information
Abstract
This document details procedures for installing the Aispa’s AiHao-4000 DC INT EXT, a Macro-
class eNodeB variant and its place in the Airspan product suite. This document is intended for
qualified personnel with a working knowledge of LTE.
Revision History
Revision Details
Date
Summary of Changes
Rev 0.1 - 0.4
August 2016
Initial document –draft
comments
Rev A
TBD 2016
Published

This document is available at: AirHarmony 4000 DC INT EXT Installation Guide

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 2
Warnings and Cautions
Human Exposure to Radio Frequencies
The AirHarmony-4000 DC INT EXT antennas should be operated from a minimum safe distance of
3.90 m
Radio Interference
The AirHarmony-4000 DC INT EXT generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment on and off, the technician is encouraged to try
to correct the interference by performing one or more of the following measures:
Re-orientate or relocate the unit
Increase separation between the units and/or End Devices
Connect the equipment to an outlet on a circuit different from that to which the power
source is connected
Modifications
Any changes and modifications to this device that are not expressly approved by Airspan Networks
may void the user's authority to operate the equipment.
General
Only qualified personnel should be allowed to install, replace, and service the equipment.
The device cannot be sold retail, to the general public or by mail order. It must be sold to
operators.
Installation must be controlled.
Installation must be performed by licensed professionals.
Installation requires special training. The AirHarmony-4000 DC INT EXT should be installed
ONLY by experienced installation professionals who are familiar with local building and
safety codes and, wherever applicable, are licensed by the appropriate government
regulatory authorities. Failure to do so may void Airspan's product warranty and may expose
the end user or the service provider to legal and financial liabilities. Airspan and its resellers
or distributors are not liable for injury, damage or violation of regulations associated with
the installation of outdoor units or antennas.
The device is to be installed in a Restricted Access Location.
Power provided by PoE output cannot be considered limited power source (LPS) per IEC/UL
60950-1 clause 2.5.
Connection to the PoE port is permitted only by certified electrician according to NEC
requirements.
Connect PoE terminal only to euipet hih does ΠOT euie ΚP“ ol feedig.
Surge Arrestors and Transient Voltage Surge Suppressors installed external to the ITE are
required to comply with the appropriate CEC/NEC requirements.
Equipment connected to the PoE port must have its own fire enclosure.

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 3
Important Safety Instructions
Read and Save these instructions
This Installation Guide contains instructions and warnings that should be followed during
installation, and operation.
Failure to follow these instructions could cause bodily injury and/or product failure
Safety
1. Read this guide and follow all operating and safety instructions.
2. Keep all product information for future reference.
3. Static sensitive components inside - do not remove the lid or base: No user serviceable
parts inside.
4. Position the power cord to avoid possible damage, do not overload circuits.
5. Do not place this product on or near a direct heat source, and avoid placing objects on
the terminal.
6. To avoid electrical shock do not install this device during adverse conditions such as rain
or inclement weather.
7. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the
power before cleaning.
8. The units should not be located too near power lines or other electrical power circuits,
where it can come into contact with such power lines or circuits.
9. The radio transceiver must be properly grounded to protect against power surges and
auulated stati eletiit. It is the use’s esposiilit to istall this deie i
accordance with the local electrical codes.
10. Installation of the AirHarmony-4000 DC INT EXT must be contracted to a professional
installer.
11. The circuit breaker should be easily accessible in case you have to disconnect the device.
12. When installed in the final configuration, the product must comply with the applicable
Safety Standards and regulatory requirements of the country in which it is installed. If
necessary, consult with the appropriate regulatory agencies and inspection authorities
to ensure compliance.
Warning of Hazardous Voltages
On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power.
Remove metal jewelry that could come into contact with AC power.
On DC sections, short-circuiting the low voltage, low impedance circuits can cause severe arcing that
may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits.
Note: Airspan products do not contain hazardous substances (as defined in UK Control of
Substances Hazardous to Health Regulations 1989 and the Dangerous Substances Regulations
1990). At the end of any Airspan products life cycle, the customer should consult with Airspan to
ensure that the product is disposed of in conformance with the relevant regulatory requirements.

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 4
Adherence to European Directive 1999/5/EC
European Council Recommendation 1999/5/EC details basic restrictions and reference levels on
human exposure to electromagnetic fields as advised by the ICNIRP. Adherence to these
recommended restrictions and reference levels should provide a high level of protection as regards
the established health effects that may result from exposure to electromagnetic fields
Airspan equipment is compliant with CE and R&TTE regulations and can be operated in all EU
(European Union) locations listed below:
Country Code
BE
EL
LT
PT
BG
ES
LU
RO
CZ
FR
HU
SI
DK
HR
MT
SK
DE
IT
NL
FI
EE
CY
AT
SE
IE
LV
PL
UK
Warning Symbols
The following symbols may be encountered during installation or troubleshooting. These warning
symbols mean danger. Bodily injury may result if you are not aware of the safety hazards involved in
working with electrical equipment and radio transmitters. Familiarize yourself with standard safety
practices before continuing.
Caution, hot surface
Caution
Electro-Magnetic
Radiation
High Voltage
Service Information
Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void
the warranty.
Disconnect the power to this product and return it for service if the following conditions apply:
a. The terminal does not function after following the operating instructions outlined in this
manual.
b. The product has been dropped or the housing is damaged.
Locate the serial number of the terminal and record this on your registration card for future
reference. Also record the MAC address, located on the product sticker.

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 5
UL Information
- The equipment must be properly grounded according with NEC and other local safety code
requirements.
- Reminder to all the BWA system installers: Attention to Section 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected
to the grounding system of the building, as close to the point of cable entry as is practical.
- AirHarmony-4000 DC is designed to operate in environmental conditions complying with IP66 and
relevant standards.
Lightning Protection
WARNING: The following notes are general recommendations for the system. The wireless
equipment should be installed by a qualified professional installer and must follow local and national
codes for electrical grounding and safety. Failure to meet safety requirements and/or use of non-
standard practices and procedures could result in personal injury and damage to equipment. A direct
lightning strike may cause serious damage even if these guidelines are followed.
All outdoor wireless equipment is susceptible to lightning damage from a direct hit or induced
current from a near strike. Lightning protection and grounding practices in local and national
electrical codes serve to minimize equipment damage, service outages, and serious injury. Reasons
for lightning damage are summarized as:
- Poorly grounded tower/antenna sites that can conduct high lightning strike energy into equipment.
- Lack of properly installed lightning protection equipment that can cause equipment failures from
lightning induced currents.
A lighting protection system provides a means by which the energy may enter earth without passing
through and damaging parts of a structure. A lightning protection system does not prevent lightning
from striking; it provides a means for controlling it and preventing damage by providing a low
resistance path for the discharge of energy to travel safely to ground. Improperly grounded
connections are also a source of noise that can cause sensitive equipment to malfunction.
A good tower grounding system disperses most of the surge energy from a tower strike away from
the building and equipment.
To limit the equipment damage due to a lightning strike, the following practices are recommended
for the wireless system:
- Provide direct grounding from the antenna mounting bracket, the radio and antenna and the
lightning/surge protectors to the same ground point at the base of the tower or a ground bus on the
building. Use the grounding screws on the antenna bracket and the radio and antenna for
terminating the ground wires.
- The circuit ground must be connected to the same grounding system as the eNodeB.
Outdoor Ethernet Cabling
- Ethernet cable connected to should be outdoor grade with UV protection.
- Use shielded out CAT5e (minimum) cabled terminated with metallic RJ45 connectors.

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 6
- In order to protect the indoor unit, install surge protection circuits on all copper cables on their
entrance to the building.
- Surge protection circuit must use a minimum 16AWG grounding cable.
DECLARATION OF CONFORMITY
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
English:
This equipment is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC.
Deutsch:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden Vorgaben der
Richtlinie 1999/5/EU.
Dansk:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Directiv
1999/5/EF.
Español:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directive 1999/5/EC.
Greek:
 Η ΑΑ Aispa ΗΩΙ Ι  Ι ΩΑΙ  Ι ΙΩΙ ΑΑΙΗΙ
ΑΙ Ι Ι Ι ΙΑΑΙ Η ΗΙΑ 1/5/.
Français:
Cet appareil est conforme aux exigencies essentialles et aux autres dispositions pertinantes de la Directive
1999/5/EC.
Íslenska:
Þessi búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipunar 1999/5/ESB.
Italiano:
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/EC.
Nederlands:
Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijn 1999/5/EC.
Norsk:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-directiv
1999/5/EC.
Português:
Este equipamento satisfaz os requisitos essenciais e outras provisões da Directiva 1999/5/EC.
Suomalainen:
Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimukset ja on siinä asetettujen muidenkin ehtojen
mukainen.

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 7
Svenska:
Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i
Direktiv 1999/5/EC.
Român:
Acest echipament este în conformitate cu eiţele eseţiale şi alte peedei eleate ale Dietiei
1999/5/CE.
The Declaration of Conformity related to this product can be obtained from [e-mail].
GPS Compliance
The GPS is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC."
The GPS complies with the following EMC Common Regulatory Testing standards:
EN55022: Radiated and Conducted Emissions
CISPR 22: Class B
EN 50081-1: Generic Emissions Class B
EN 50082-1: Generic Immunity Class B
EN 61000-4-2: Electrostatic Discharge Immunity
EN 61000-4-3: Radiated RF EM Field Immunity Test
EN 61000-4-4: Electrical Fast Transient/Burst Test
EN 61000-4-6: Conducted Immunity
EN 61000-4-8: Magnetic Field Immunity
Note: A GPS is recommended for synchronizing between LTE sectors.
Note: An optional GPS Lightning/Surge protector is available from Airspan when installing the GPS
antenna in a remote location for lightning prone deployments.
Maximum Output TX Total Power
Table 1: AirHarmony--4000 DC INT EXT FCC Maximum Output TX Total Power
Frequency Band
(MHz)
FCC
TX (dBm) EIRP (dBm)
Antenna Gain
(dBi)
728-746
46.06
59.56
13.5
Table 2: AirHarmony-4000 DC INT EXT ETSI Maximum Output TX Total Power
Frequency Band
(MHz)
ETSI
TX (dBm) EIRP (dBm)
Antenna Gain
(dBi)
729-746
46
59.5
13.5
Caution: Do not set maximum output TX power to higher than local regulations.

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 8
Power Consumption –Supply and Current
AirHarmony-4000 DC INT EXT supports direct connection to DC power source.
DC Power Source requirements are:
Operational Voltage Range: -40.5 to -57 VDCMax, 8A Max
Safety approved (certified) according to IEC/EN/UL 60950-1
Transient Voltage: +150V (ETR283)
The use of other power sources may impair safety
AC power feed is also available, using an AC/DC power converter offered by Airspan.
Warning: Power provided by PoE outputs (RJ45 ETH1, ETH2) cannot be considered limited power
source (LPS) per IEC/UL 60950-1 clause 2.5
Table 3: Power Consumption
Duplex
Tx Power
at RF
Port
(dBm)
Band
Power
Source
Nominal
Power
Consumption
(W)
MAX Power
Consumption
with PoE
(Instantaneous)
(W)
MAX Current
with PoE
(Instantaneous)
(A)
PoE Maximum
Power
Consumption
(W)
Power Supply
Requirements
(W)
FDD
2 x 43
B12
DC
TBD
TBD
9
60
400
FDD
2 x 43
B17
DC
TBD
TBD
9
60
400

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 9
Antenna System
AirHarmony-4000 DC INT EXT comes in a range of frequency variants that can be mounted with
different antenna options and formats. A typical installation will have a cross-polar sector or dual
slant antenna connected to the appropriate Integrated External Duplexers of the AirHarmony-4000
DC INT EXT variant unit. Various antennas are designed specifically for AirHarmony-4000 DC INT EXT
deployments; specifications are available from Airspan separately.
External Antenna
The externally mounted antenna should be a dual slant or cross polarized fixed antenna which is
connected via DIN connectors located on the Integrated Duplexers. The antenna should be mounted
to its appropriate mounting facility.
Figure 1: AirHarmony-4000 DC INT EXT with Integrated External Duplexers

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 10
About This Document
Purpose
This guide provides the workflow and step-by-step procedures for installing the Aispa’s
AirHarmony-4000 DC INT EXT Macro-class eNodeB variant. These procedures include:
Verify prerequisites
Mount GPS
Install Mounting bracket
Install the AirHarmony-4000 DC INT EXT
Mount Antenna (external antenna)
Mount iRelay (if applicable)
Connect to External Antenna (if applicable)
Connect and manage cables
Intended Audience
This guide is intended for persons who are responsible for installing the AirHarmony-4000 DC INT
EXT.
These persons should have a working knowledge of the equipment.
AiHao a e tightl itegated ith Aispa’s iBidge ad iRela transport solutions.
AirHarmony-4000 DC INT EXT supports an integrated PoE interface which powers and connects
either iBridge, iRelay, or a third party WiFi Access Point. This configuration creates a single piece
installation that supports full end to end IPv6 plug and play deployment by just adding power. For
more details please refer to the iBridge and iRelay product specifications.
Document Conventions
This document uses the following typographic conventions.
Table 4: Typographic Conventions
Convention
Element
Blue underlined text
Cross-reference links.
Bold text
Keyboard buttons and GUI elements.
Command
Command names or phrases.
Computer output
Text displayed by the computer.
Hyperlinks
Website and e-mail addresses.
Danger
Signifies a hazardous situation—if not avoided—will cause
death or serious injury. Describes how to avoid it.
Warning
Signifies a hazardous situation—if not avoided—can cause
death or serious personal injury. Describes how to avoid it.

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 11
Convention
Element
Caution
Signifies a hazardous situation—if not avoided—can void
the product warranty, and cause property damage.
Describes how to avoid it.
Important
Provides necessary information to explain a task.
Note
Provides additional information.
Tip
Provides helpful hints.

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 12
Document Organization
Chapter
Contents
Introduction
Provides a comprehensive overview of AirHarmony-4000 DC INT EXT
and its installation.
Getting Started
Provides workflows for initial install and workflow.
Verifying Prerequisites
Lists the hardware, software, and client requirements for
installation.
AirHarmony-4000 Installation
Describes how to install AirHarmony-4000 DC INT EXT.
GPS Installation
Describes how to install the GPS antenna.
Connect and Manage Cables
Describes how to connect the cables.
Job Sheet
Provides information that aids users in performing the installation.
Abbreviations
Lists the abbreviations used in this document and their expansions.
Related Reading
The following documents contain related information:
AirHarmony-4000 Hardware Product Specification
Airspan LTE Commissioning Manual

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 13
Customer Care Help Desk
Aispa’s Customer Care Help Desk offers prompt and efficient customer support services.
Note: To avail Airspa’s Customer Care Help Desk support, you must be a registered user and must
have a valid support contract. To register, click here and fill the Registration form.
To create and update issue logs, send e-mails to Customer Care Help Desk. Once you submit your
issue, the system generates a new issue and sends an issue number for your reference. The system
uses this issue number to categorize and store e-mails under the appropriate issue.
To help Customer Care Help Desk identify your issue, include the issue number and your Customer
Care Helpdesk account details in all further communications.
Main Operations
Airspan Communications Ltd.
Capital Point
33 Bath Road
Slough, Berkshire
SL1 3UF, United Kingdom
Tel: [phone]
Worldwide Headquarters
Airspan Networks Inc.
777, Yamato Road, Suite 105
Boca Raton, FL 3341-4408, USA
Tel: [phone]
Airspan Encourages Comments
Airspan welcomes any feedback and suggestions that help to improve the quality of the
documentation. Send your feedback to documentfeedb[email protected].

AirHarmony-4000 DC (Integrated External Duplexers) Installation Guide
UGD-D01123 Airspan Commercial and Internal Use 14
1Introduction
This setio poides a desiptie oeie of the Aispa’s AirHarmony-4000 with Integrated
External Duplexers a Macro-class eNodeB variant and its place in the Airspan product suite.
This document is intended for readers with LTE working knowledge.
All information in this document is for general information only, and is subject for change without
notice.
1.1 AirHarmony-4000
AirHarmony-4000 is part of Aispa’s aie-class LTE Advanced small cell eNodeB family.
AirHarmony-4000 is a Macro-class product that supports 3GPP’s Long Term Evolution (LTE) eNodeB
specifications, providing high-speed data, mobility, Voice over LTE, and broadcast/multicast services
in order to meet the demands of the LTE Mobile Carriers.
AirHarmony-4000 is a compact, easy to install Macro-class eNodeB, allowing an operator to deploy
LTE broadband services using existing infrastructure or Street Furniture (e.g. street lamps, power
poles, uildig ooftop o sides et…
AirHarmony-4000 employs Software Defined Radio (SDR) technology, together with two transmit
and receive paths for each sector and a GPS antenna and receiver –all in a highly integrated,
physically small and light, All-Outdoor package, targeted to blend seamlessly into the urban
environment. This compact outdoor product minimizes physical footprint, power consumption and
operator OPEX.
AirHarmony-4000 is a 2T2R solution that enables a flexible deployment scenarios, but can achieve
higher coverage and throughput by combing multiple eNodeBs enabling the support of 4T4R, 4T8R,
and 8T8R.
AirHarmony-4000 implements 2 x 20W transmitters (2 x 43 dBm) and fully supports the standard LTE
(Uu/S1/X2) interfaces.
All Airspan eNodeB products, including AirHarmony-4000, are interoperable with a rich portfolio of
3rd party end user devices, including many handsets, indoor UEs, outdoor UEs and USB dongles from
several ODMs, using various chipsets. For an updated of interoperability list, please contact your
nearest Airspan Sales Representative.
Additionally, AiHao a e tightl itegated ith Aispa’s iBidge ad iRela transport
solutions. AirHarmony-4000 supports an integrated PoE interface which powers and connects either
iBridge, iRelay, or a third party Wi-Fi Access Point. This configuration creates a single installation that
fully supports end to end IPv6 plug and play deployment by just adding power. For more details
please refer to the iBridge and iRelay product specifications.
Note: For management please refer to the Airspan LTE Commissioning Manual as well as Netspan.
1.2 Deployment
A highly flexible and scalable 4G Base Station, the AirHarmony-4000 DC INT EXT is capable of
supporting LTE profiles across multiple frequency bands.