Airspan AirHarmony-4200 DC User manual

AirHarmony-4200 DC Installation Guide
Internal Filters
Part Number: UGD-D01196
System Release: 16.0
Revision: A
Published: March 2019

© Copyright by Airspan Networks Ltd., 2018-2019. All rights reserved worldwide.
Legal Notices
The information contained within this document is proprietary, privileged and intended only for the recipient. As such, the
information is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any
specific agreements protecting Airspan Networks Ltd. rights in the aforesaid information. Neither this document nor the
information contained herein may be published, reproduced, transmitted or disclosed to third parties, in whole or in part,
without the express, prior, written permission of Airspan Networks Ltd. In addition, any use of this document or the
information contained herein for the purposes other than those for which it is disclosed is strictly forbidden.
Airspan Networks Ltd. reserves the right, without prior notice or liability, to make changes in equipment design or
specifications.
Information supplied by Airspan Networks Ltd. is believed in good faith to be accurate and reliable, while every care has
been taken in preparing these documents. However, Airspan Networks Ltd. does not make any representations and gives
no warranties of whatever nature in respect of these documents, including without limitation, the accuracy or
completeness of any information, facts and/or opinions contained therein. No responsibility is assumed by Airspan
Networks Ltd. for the use of the documents nor for the rights of third parties which may be effected in any way by the use
thereof. The provision of these documents (and the documents themselves) does not constitute professional advice of any
kind. Any representation(s) in these documents concerning performance of Airspan Networks Ltd. product(s) are for
informational purposes only and are not warranties of future performance, either expressed or implied. Airspan Networks
Ltd., its affiliates, directors, employees and agents shall not be held liable for any damages or losses, of any nature
whatsoever, arising from any use of and/or reliance on the documents.
These documents may contain flaws, omissions or typesetting errors; no warranty is granted nor liability assumed in
relation thereto unless specifically undertaken in Airspan Networks Ltd. sales contract or order confirmation. Information
contained herein is periodically updated and changes will be incorporated into subsequent editions. If you have
encountered an error, please notify Airspan Networks Ltd.
Product performance figures quoted within this document are indicative and for information purposes only.
UK WEEE Registration number: WEEE/AB0207WZ. For more information, see WEEE Information for Airspan
Customers and Recyclers.
Acknowledgements
© Intel Corporation http://www.intel.com/
© Microsoft Corporation http://www.microsoft.com

UGD-D01196 Airspan Commercial and Internal Use i
Table of Contents
Document Information ......................................................................................1
Abstract............................................................................................................................ 1
Revision History................................................................................................................ 1
Warnings and Cautions ......................................................................................2
Human Exposure to Radio Frequencies............................................................................. 2
Radio Interference............................................................................................................ 2
Modifications ................................................................................................................... 2
General............................................................................................................................. 2
Général............................................................................................................................. 2
Important Safety Instructions ..................................................................................... 3
Safety ............................................................................................................................... 4
Securite ............................................................................................................................ 4
Warning of Hazardous Voltages........................................................................................ 5
Attention aux Voltages Hasardeux.................................................................................... 5
Adherence to European Directive 2014/53/EU ................................................................. 6
Warning Symbols.............................................................................................................. 6
Service Information .......................................................................................................... 6
UL Information ................................................................................................................. 6
Lightning Protection ......................................................................................................... 7
Outdoor Ethernet Cabling................................................................................................. 7
DECLARATION OF CONFORMITY ....................................................................................... 8
GPS Compliance.............................................................................................................. 10
Maximum Output TX Total Power....................................................................10
Power Consumption - Supply and Current ...................................................................... 10
Antenna System ............................................................................................................. 12
External Antenna............................................................................................................ 12
About This Document ......................................................................................13

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use ii
Purpose .......................................................................................................................... 13
Intended Audience ......................................................................................................... 13
Document Conventions .................................................................................................. 13
Document Organization.................................................................................................. 14
Related Reading.............................................................................................................. 14
Customer Care Help Desk ................................................................................15
Airspan Encourages Comments ...................................................................................... 15
1Introduction.................................................................................................16
1.1 AirHarmony-4200 DC Internal Filters....................................................................... 16
1.2 Deployment ............................................................................................................ 17
1.3 Related AirHarmony 4200 DC Internal Filters Variants............................................. 18
2Getting Started ............................................................................................19
2.1 Workflow of Installation.......................................................................................... 19
2.2 AirHarmony-4200 DC Internal Filters Installation Checklist...................................... 20
3Verifying Prerequisites.................................................................................20
3.1 Verifying Site Requirements .................................................................................... 20
3.2 Verify Installation Requirements ............................................................................. 20
Verify the Tools ................................................................................................................. 20
Verify the Parts and Kits..................................................................................................... 21
Panels 23
Physical Dimensions .......................................................................................................... 24
Environmental................................................................................................................... 25
4Installing AirHarmony-4200 DC....................................................................26
4.1 Connecting the GPS Antenna................................................................................... 26
4.2 Pole/Wall Mount Assembly ..................................................................................... 27
Mounting on a Pole ........................................................................................................... 27
Mounting on a Wooden Pole ............................................................................................. 28
Mounting on a Wall ........................................................................................................... 30
4.3 Securing AirHarmony-4200 DC to the Mounting Plate............................................. 32

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use iii
5AirHarmony-4200 DC Connections...............................................................36
5.1 Grounding ............................................................................................................... 36
5.2 Remote Antenna Assembly ..................................................................................... 36
Connecting RF Jumper Cables to External Antenna ............................................................ 36
Weather-proofing the Antenna Connections...................................................................... 37
5.3 Cable Connections................................................................................................... 37
Copper Ethernet Cable Assembly....................................................................................... 37
5.4 Fiber Ethernet (SFP) Cable Installation..................................................................... 38
SFP Cable Connection ........................................................................................................ 39
5.5 Connecting the DC Power Cable to AirHarmony-4200 DC........................................ 41
Power Input –DC............................................................................................................... 41
Connecting the DC Power Cable to AirHarmony................................................................. 42
AC/DC Power Converter –Optional ................................................................................... 43
AJob Sheet .....................................................................................................44
BAbbreviations...............................................................................................45
Figures
Figure 1: AirHarmony-4200 DC Internal Filters................................................................................. 12
Figure 2: AirHarmony-4200 DC Internal Filters unit.......................................................................... 17
Figure 3: Workflow.......................................................................................................................... 19
Figure 4: AirHarmony-4200 DC Internal Filters Unit, Bottom panel .................................................. 23
Figure 5: AirHarmony-4200 DC Internal Filters Unit, Top panel ........................................................ 24
Figure 6: Attaching GPS antenna to unit .......................................................................................... 26
Figure 7: Pole/Wall mounting plate (w/o bolt)................................................................................. 27
Figure 8: Mounting plate mounted .................................................................................................. 28
Figure 9: Pole/Wall mounting plate ................................................................................................. 28
Figure 10: Mounting plate on pole................................................................................................... 29
Figure 11: Through-bolt & Mounting plate....................................................................................... 30
Figure 12: Mounting Plate on Wall................................................................................................... 31
Figure 13: Lift unit and fit the slotted holes unto studs on top of mounting plate ............................ 32
Figure 14: Align Pins ........................................................................................................................ 32
Figure 15: AirHarmony mounted on concrete Pole .......................................................................... 33
Figure 16: AirHarmony mounted Wooden Pole................................................................................ 34
Figure 17: AirHarmony mounted on a Wall...................................................................................... 35
Figure 18: Grounding....................................................................................................................... 36
Figure 19: Gland connector - copper................................................................................................ 38

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use iv
Figure 20: Ethernet Cable through connector .................................................................................. 38
Figure 21: LC duplex cable assembly................................................................................................ 39
Figure 22: Cable connector hook up to the board connector............................................................ 39
Figure 23: Slide on inner housing..................................................................................................... 40
Figure 24: Slide over and click.......................................................................................................... 40
Figure 25: DC Power Connection ..................................................................................................... 41
Figure 26: Power Connector –Bottom Panel ................................................................................... 42
Figure 27: attaching power cable to AirHarmony............................................................................. 42
Figure 28: Optional AC/DC Converter .............................................................................................. 43
Tables
Table 1: AirHarmony-4200 DC Internal Filter FCC Maximum Output TX Total Power ........................ 10
Table 2: AirHarmony-4200 DC Internal Filter ETSI Maximum Output TX Total Power ....................... 10
Table 3: Power Consumption........................................................................................................... 11
Table 4: AW3089 Omni Antenna...................................................................................................... 12
Table 4: Typographic Conventions ................................................................................................... 13
Table 5: AirHarmony 4200 DC Variants ............................................................................................ 18
Table 6. Minimum Hardware Requirements .................................................................................... 20
Table 7. Parts & Kits......................................................................................................................... 21
Table 8: AirHarmony-4200 DC Physical Dimensions ......................................................................... 24
Table 9: AirHarmony-4200 DC Environment Compliance ................................................................. 25
Table 10: AC/DC Converter Specifications........................................................................................ 43
Table 11: Job Sheet.......................................................................................................................... 44

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 1
Document Information
Abstract
This document details procedures for installing the Airspan’s AirHarmony-4200 DC, with internal
filters, a mini-Macro class eNodeB variant and its place in the Airspan product suite. This document
is intended for qualified personnel with a working knowledge of LTE.
Revision History
Revision Details
Date
Summary of Changes
Rev 0.1, 0.2
November 2016
Initial document –draft
comments
Rev A
November 2016
Updated drawings
Publish
Rev A1
November 2017
Power Input –DC addition
Rev A2
May 2018
Antenna ports
Rev A3
March 2019
Modified Minimum Safety Distance
Rev A4
March 2019
Updated EU Directive
Added “Airspan FCC-specific” notes
This document is available at: AirHarmony 4200 DC Internal Filters Installation Guide

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 2
Warnings and Cautions
Human Exposure to Radio Frequencies
The AirHarmony-4200 DC Internal Filters antennas should be operated from a minimum safe
distance of 59 Cm (23.22 inches).
Radio Interference
The AirHarmony-4200 DC Internal Filters generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment on and off, the technician is
encouraged to try to correct the interference by performing one or more of the following measures:
Re-orientate or relocate the unit
Increase separation between the units and/or End Devices
Connect the equipment to an outlet on a circuit different from that to which the power
source is connected
Modifications
Any changes and modifications to this device that are not expressly approved by Airspan Networks
may void the user's authority to operate the equipment.
General
Only qualified personnel should be allowed to install, replace, and service the equipment.
The device cannot be sold retail, to the general public or by mail order. It must be sold to
operators.
Installation must be controlled.
Installation must be performed by licensed professionals according to FCC 96.39.
Installation requires special training. The AirHarmony-4200 should be installed ONLY by
experienced installation professionals who are familiar with local building and safety codes
and, wherever applicable, are licensed by the appropriate government regulatory
authorities. Failure to do so may void Airspan's product warranty and may expose the end
user or the service provider to legal and financial liabilities. Airspan and its resellers or
distributors are not liable for injury, damage or violation of regulations associated with the
installation of outdoor units or antennas.
The device is to be installed in a Restricted Access Location.
Installation is restricted to non-marine type area environments.
Surge Arrestors and Transient Voltage Surge Suppressors installed external to the ITE are
required to comply with the appropriate CEC/NEC requirements.
Général
Seul le personnel qualifié peut être autorisé pour installer ou remplacer l’équipement ainsi
qu’effectuer les opérations de maintenance pour cet équipement.
L’équipement ne peut pas être vendu en grande distribution ou par commande via email à
destination du public. Il doit être vendu aux opérateurs de télécommunications.

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 3
Son installation doit être contrôlée
Son Installation doit être effectuée par des professionnels autorises selon FCC 96.39.
Son installation requiert une formation spécifique du personnel. L’AirHarmony-4200, radio
et antenne doit être installe UNIQUEMENT par des installateurs professionnels
expérimentés et ayant une connaissance des constructions locales et règles de sécurité, ainsi
que, dès que nécessaire, disposant d’un agreement des autorités gouvernementales de
régulation. Toute enfreinte a ces obligations peut annuler la garantie délivrée par Airspan
pour ces produits et peut exposer l’utilisateur final ou le fournisseur de services a des
dommages légaux et financiers.
Airspan et ses revendeurs ou ses distributeurs ne sont pas responsables des blessures,
dommages ou violations de la régulation en vigueur lies a l’installation du système extérieur
ou des antennes.
L’Equipment doit être installe dans une zone a accès réduit et contrôle.
L'installation est limitée aux environnements de type non-marin.
Parafoudres et Protections contre les surtensions transitoires doivent etre installés a
l’exterieur de l’équipement ITE sont tenus de se conformer aux exigences relatives aux
normes CEC/NEC concernées
Important Safety Instructions
Read and Save these instructions
This Installation Guide contains instructions and warnings that should be followed during
installation, and operation.
Failure to follow these instructions could cause bodily injury and/or product failure

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 4
Safety
1. Read this guide and follow all operating and safety instructions.
2. Keep all product information for future reference.
3. Static sensitive components inside - do not remove the lid or base: No user serviceable
parts inside.
4. Position the power cord to avoid possible damage, do not overload circuits.
5. Do not place this product on or near a direct heat source, and avoid placing objects on
the terminal.
6. To avoid electrical shock do not install this device during adverse conditions such as rain
or inclement weather.
7. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the
power before cleaning.
8. The units should not be located too near power lines or other electrical power circuits,
where it can come into contact with such power lines or circuits.
9. The radio transceiver must be properly grounded to protect against power surges and
accumulated static electricity. It is the user’s responsibility to install this device in
accordance with the local electrical codes.
10. Installation of the AirHarmony-4200 DC Internal Filters must be contracted to a
professional installer.
11. The circuit breaker should be easily accessible in case you have to disconnect the device.
12. When installed in the final configuration, the product must comply with the applicable
Safety Standards and regulatory requirements of the country in which it is installed. If
necessary, consult with the appropriate regulatory agencies and inspection authorities
to ensure compliance.
Securite
1. Lire attentivement ce guide et suivre les instructions d’utilisation et de sécurité.
2. Des composants sensibles a électricité statique sont utilisés à l’intérieur. Ne pas retirer le
coffre ou la base. Aucune pièce a l’intérieur est d’utilité pour l’utilisateur.
3. La connexion "terre" doit être effectuée en priorité et avant d'effectuer les connexions à
la source d'alimentation (phase et neutre).
4. Positionner le cordon d’alimentation de façon à éviter des dommages potentiels. Ne pas
surcharger les circuits.
5. Ne pas placer ce produit sur ou à proximité d’une source directe de chaleur et éviter de
placer des objets sur le terminal.
6. Afin d’éviter des problèmes électriques, ne pas installer cet équipement au cours
d’évènements climatiques difficiles comme averses ou météo non clémente.
7. Utiliser uniquement chiffon de coton pour nettoyage. Ne pas utiliser de produits liquides
ou d’aérosols. Déconnecter le produit de la source d’alimentation avant nettoyage.
8. L’unité ne doit pas être située trop près de lignes électriques ou autres circuits de
puissance, avec lesquels il pourrait entrer en contact.

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 5
9. L’émetteur radio doit être correctement relie a la terre afin de le protéger contre les
surtensions ou accumulation d’électricité statique. L’utilisateur est tenu responsable de
l’installation du produit conformément aux règles électrique en vigueur localement.
10. L’installation de AirHarmony-4000 DC doit être contractualisée avec un installateur
professionnel.
11. L’interrupteur de circuit électrique doit être facilement accessible afin de pouvoir
déconnecter l’équipement.
12. Lors de l’installation de la configuration finale, le produit doit être conforme aux
Standards de Sécurité en vigueur ainsi qu’aux exigences réglementaires du pays dans
lequel il est installé. Si nécessaire, consulter les agences règlementaires appropriées,
ainsi que les autorités chargées de l’inspection afin de garantir la conformité.
Warning of Hazardous Voltages
On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power.
Remove metal jewelry that could come into contact with AC power.
On DC sections, short-circuiting the low voltage, low impedance circuits can cause severe arcing that
may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits.
Note: Airspan products do not contain hazardous substances (as defined in UK Control of
Substances Hazardous to Health Regulations 1989 and the Dangerous Substances Regulations
1990). At the end of any Airspan products life cycle, the customer should consult with Airspan to
ensure that the product is disposed of in conformance with the relevant regulatory requirements.
Attention aux Voltages Hasardeux
Sur les installations de réseau électrique de type courant alternatif (CA), des voltages hasardeux
peuvent survenir. Garder une Attention particulière lors d’une vérification ou de travaux sur réseau
électrique CA. Retirer tous bijoux en métal qui pourraient entrer en contact avec l’alimentation ou le
réseau CA.
Sur les portions de réseau électrique de type courant continu (CC), un circuit basse impédance peut
causer de sérieux arcs électriques qui pourraient bruler ou endommager les yeux. Retirer bagues,
anneaux, montres etc… afin d’éviter les court-circuit sur le réseau CC.

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 6
Adherence to European Directive 2014/53/EU
European Council Recommendation 2014/53/EU details basic restrictions and reference levels on
human exposure to electromagnetic fields as advised by the ICNIRP. Adherence to these
recommended restrictions and reference levels should provide a high level of protection as regards
the established health effects that may result from exposure to electromagnetic fields.
Airspan equipment is compliant with CE and R&TTE regulations and can be operated in all EU
(European Union) locations listed below:
Country Code
BE
EL
LT
PT
BG
ES
LU
RO
CZ
FR
HU
SI
DK
HR
MT
SK
DE
IT
NL
FI
EE
CY
AT
SE
IE
LV
PL
UK
Warning Symbols
The following symbols may be encountered during installation or troubleshooting. These warning
symbols mean danger. Bodily injury may result if you are not aware of the safety hazards involved in
working with electrical equipment and radio transmitters. Familiarize yourself with standard safety
practices before continuing.
Caution, hot surface
Caution
Electro-Magnetic
Radiation
DC
Service Information
Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void
the warranty.
Disconnect the power to this product and return it for service if the following conditions apply:
a. The terminal does not function after following the operating instructions outlined in this
manual.
b. The product has been dropped or the housing is damaged.
Locate the serial number of the terminal and record this on your registration card for future
reference. Also record the MAC address, located on the product sticker.
UL Information
- The equipment must be properly grounded according with NEC and other local safety code
requirements.

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 7
- Reminder to all the BWA system installers: Attention to Section 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected
to the grounding system of the building, as close to the point of cable entry as is practical.
- AirHarmony-4200 DC is designed to operate in environmental conditions complying with IP66 and
relevant standards.
Lightning Protection
WARNING: The following notes are general recommendations for the system. The wireless
equipment should be installed by a qualified professional installer and must follow local and national
codes for electrical grounding and safety. Failure to meet safety requirements and/or use of non-
standard practices and procedures could result in personal injury and damage to equipment. A direct
lightning strike may cause serious damage even if these guidelines are followed.
All outdoor wireless equipment is susceptible to lightning damage from a direct hit or induced
current from a near strike. Lightning protection and grounding practices in local and national
electrical codes serve to minimize equipment damage, service outages, and serious injury. Reasons
for lightning damage are summarized as:
- Poorly grounded tower/antenna sites that can conduct high lightning strike energy into equipment.
- Lack of properly installed lightning protection equipment that can cause equipment failures from
lightning induced currents.
A lighting protection system provides a means by which the energy may enter earth without passing
through and damaging parts of a structure. A lightning protection system does not prevent lightning
from striking; it provides a means for controlling it and preventing damage by providing a low
resistance path for the discharge of energy to travel safely to ground. Improperly grounded
connections are also a source of noise that can cause sensitive equipment to malfunction.
A good tower grounding system disperses most of the surge energy from a tower strike away from
the building and equipment.
To limit the equipment damage due to a lightning strike, the following practices are recommended
for the wireless system:
- Provide direct grounding from the antenna mounting bracket, the radio and antenna and the
lightning/surge protectors to the same ground point at the base of the tower or a ground bus on the
building. Use the grounding screws on the antenna bracket and the radio and antenna for
terminating the ground wires.
- The circuit ground must be connected to the same grounding system as the eNodeB.
Outdoor Ethernet Cabling
- Ethernet cable connected to should be outdoor grade with UV protection.
- Use shielded out CAT5e (minimum) cabled terminated with metallic RJ45 connectors.
- In order to protect the indoor unit, install surge protection circuits on all copper cables on their
entrance to the building.
- Surge protection circuit must use a minimum 16AWG grounding cable.

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 8
DECLARATION OF CONFORMITY
Declaration of Conformity with Regard to the R&TTE Directive 2014/53/EU
Czech:
Airspan tímto prohlašuje, že tento přístroj je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 2014/53 / EU.
Danish:
Undertegnede, Airspan erklærer hermed, at følgende udstyrsenhed opfylder de væsentlige krav og
andre relevante krav i direktiv 2014/53 / EF.
Deutsch:
Hiermit erklärt Airspan, dass die Produkteinheit die grundlegenden Anforderungen und anderen
relevanten Bestimmungen der Richtlinie 2014/53 / EU erfüllt.
Estonian:
Käesolevaga kinnitab Airspan, et seadme seade vastab direktiivi 2014/53 / EL olulistele nõuetele ja
muudele kõnealuse direktiivi asjakohastele sätetele.
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU.
Español:
Por medio de este Airspan, declara que la unidad cumple con los requisitos esenciales y cualquier
otra disposición aplicable o exigible de la Directiva 2014/53 / UE.
Greek:
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ΠΡΟΔΙΑΓΡΑΦΗ, η Airspan ΔΗΛΩΝΕΤΑΙ ότι η μονάδα συμμορφώνεται με τις
ουσιώδεις απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 2014/53 / ΕE.
Français:
Airspan déclare par la présente que l'appareil est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 2014/53 / UE.
Italiano:
Con la presente Airspan dichiara che questa unità è conforme ai requisiti essenziali e alle altre
disposizioni pertinenti stabilite dalla direttiva 2014/53 / UE.
Latvian:
Ar šo Airspan paziņo, ka vienība atbilst Direktīvas 2014/53 / ES būtiskajām prasībām un citiem
attiecīgajiem noteikumiem;
Lithuanian:
Šis „Airspan“ pareiškia, kad šis įrenginys atitinka esminius Direktyvos 2014/53 / ES reikalavimus ir
kitas nuostatas.
Nederlands:
Airspan verklaart hierbij dat de apparaateenheid voldoet aan de essentiële vereisten en andere
relevante bepalingen van richtlijn 2014/53 / EU.

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 9
Maltese:
Hawnhekk, Airspan, tiddikjara li din l-unità tikkonforma mar-rekwiżiti essenzjali u dispożizzjonijiet
rilevanti oħra li jinsabu fid-Direttiva 2014/53 / UE.
Hungarian:
Alulírott, az Airspan kijelenti, hogy az egység megfelel a 2014/53 / EU irányelv vonatkozó alapvető
követelményeinek és egyéb követelményeinek.
Polish:
Niniejszym Airspan oświadcza, że urządzenie jest zgodne z zasadniczymi wymaganiami i innymi
odpowiednimi postanowieniami dyrektywy 2014/53 / UE.
Português:
Airspan declara que esta unidade está em conformidade com os requisitos essenciais e outras
disposições da Diretiva 2014/53 / UE.
Slovenian:
Airspan izjavlja, da je ta enota skladna z bistvenimi zahtevami in drugimi ustreznimi določbami
Direktive 2014/53 / EU.
Slovak:
Airspan týmto vyhlasuje, že tento prístroj spĺňa základné požiadavky a všetky príslušné ustanovenia
Smernice 2014/53 / EÚ.
Suomalainen:
Airspan vakuuttaa täten, että laitteen tyyppi on direktiivin 2014/53 / EU olennaisten vaatimusten ja
muiden asiaankuuluvien säännösten mukainen.
Swedish:
Därmed intygar Airspan att denna enhet överensstämmer med de väsentliga egenskapskraven och
andra relevanta bestämmelser som anges i direktiv 2014/53 / EU.
Íslenska:
Airspan lýsir hér með yfir að þessi eining uppfylli grunnkröfur og aðrar kröfur tilskipunar 2014/53 /
ESB.
Norsk:
Airspan erklærer herved at utstyrsenheten oppfyller grunnleggende krav og andre relevante krav i
direktiv 2014/53 / EU.
Român:
Airspan declarăm pe propria răspundere că produsul produsului respectă cerințele esențiale și alte
prevederi aplicabile din Directiva 2014/53 / UE.
The Declaration of Conformity related to this product can be obtained from [e-mail].

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 10
GPS Compliance
The GPS is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC."
The GPS complies with the following EMC Common Regulatory Testing standards:
EN55022: Radiated and Conducted Emissions
CISPR 22: Class B
EN 50081-1: Generic Emissions Class B
EN 50082-1: Generic Immunity Class B
EN 61000-4-2: Electrostatic Discharge Immunity
EN 61000-4-3: Radiated RF EM Field Immunity Test
EN 61000-4-4: Electrical Fast Transient/Burst Test
EN 61000-4-6: Conducted Immunity
EN 61000-4-8: Magnetic Field Immunity
Note: A GPS is recommended for synchronizing between LTE sectors.
Note: An optional GPS Lightning/Surge protector is available from Airspan when installing the GPS
antenna in a remote location for lightning prone deployments.
Maximum Output TX Total Power
Table 1: AirHarmony-4200 DC Internal Filter FCC Maximum Output TX Total Power
Frequency Band
(MHz)
FCC
TX (dBm) EIRP (dBm)
Antenna Gain
(dBi)
B48 3550-3700
36.9
46.4
9.5
Note: The AirHarmony 4200 DC Internal Filters requires operation using an Airspan FCC-specific
version of Netspan acting as a CBRS Domain Proxy.
Table 2: AirHarmony-4200 DC Internal Filter ETSI Maximum Output TX Total Power
Frequency Band
(MHz)
ETSI
TX (dBm) EIRP (dBm)
Antenna Gain
(dBi)
3400-3600
39-40
TBD
18
Caution: Do not set maximum output TX power to higher than local regulations.
Power Consumption - Supply and Current
AirHarmony-4200 DC Internal Filters supports direct connection to DC power source.
DC Power Source requirements are:
Operational Voltage Range: -40.5 to -57 VDC Max, 8A Max
Safety approved (certified) according to IEC/EN/UL 60950-1

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 11
Transient Voltage: +150V (ETR283)
The use of other power sources may impair safety
AC power feed is also available, using an AC/DC power converter offered by Airspan.
Note: For more details on the offered AC/DC converter (sold separately), please contact your
nearest Airspan sales representative.
Table 3: Power Consumption
Duplex
Tx Power
at RF
Port
(dBm)
Power
Source
Nominal
Power
Consumption
(W)
MAX Power
Consumption
with PoE
(Instantaneous)
(W)
MAX Current
with PoE
(Instantaneous)
(A)
PoE Maximum
Power
Consumption
(W)
Power Supply
Requirements
(W)
TDD
4 x 39-40
DC
265
387
4.30
60
400
TDD
4 x 36-37
DC
265
387
4.30
60
400

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 12
Antenna System
AirHarmony-4200 DC comes in a range of frequency variants that can be mounted with different
antenna options and formats. A typical installation will have a cross-polar sector or dual slant
antenna connected to the approprate RF port of the AirHarmony-4200 DC variant unit. Various
antennas are designed specifically for AirHarmony-4200 DC deployments; specifications are available
from Airspan separately.
External Antenna
The externally mounted antennas should be a dual slant or cross polarized fixed antennas which is
connected via DIN connectors located on the AirHarmony-4200 DC unit. The antennas should be
mounted to its appropriate mounting facility.
AirHarmony-4200 DC, can also support SBA configuration which can be mounted directly to the unit
or remotely. The current permitted antenna type is as specified below:
Table 4: AW3089 Omni Antenna
Frequency Range (MHz)
Antenna Gain (dBi)
Type
3300MHz –3800MHz
9.5
Dual Port, Omni, +/-45⁰Polarisation, Fixed Tilt
Note: For a list of compatible external antennas, please contact your nearest Airspan Sales
representative.
Figure 1: AirHarmony-4200 DC Internal Filters

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 13
About This Document
Purpose
This guide provides the workflow and step-by-step procedures for installing the Airspan’s
AirHarmony-4200 DC Internal Filters Macro-class eNodeB variant. These procedures include:
Verify prerequisites
Mount GPS
Install Mounting bracket
Mount iRelay (if applicable)
Mount Antenna (external antenna)
Connect and manage cables
Intended Audience
This guide is intended for persons who are responsible for installing the AirHarmony-4200 DC
Internal Filter unit.
These persons should have a working knowledge of the equipment.
AirHarmony can be tightly integrated with Airspan’s iBridge and iRelay transport solutions.
AirHarmony-4200 DC Internal Filters supports an integrated PoE interface which powers and
connects either iBridge, iRelay, or a third party WiFi Access Point. This configuration creates a single
piece installation that supports full end to end IPv6 plug and play deployment by just adding power.
For more details please refer to the iBridge and iRelay product specifications.
Document Conventions
This document uses the following typographic conventions.
Table 5: Typographic Conventions
Convention
Element
Blue underlined text
Cross-reference links.
Bold text
Keyboard buttons and GUI elements.
Command
Command names or phrases.
Computer output
Text displayed by the computer.
Hyperlinks
Website and e-mail addresses.
Danger
Signifies a hazardous situation—if not avoided—will cause
death or serious injury. Describes how to avoid it.
Warning
Signifies a hazardous situation—if not avoided—can cause
death or serious personal injury. Describes how to avoid it.
Caution
Signifies a hazardous situation—if not avoided—can void
the product warranty, and cause property damage.
Describes how to avoid it.
Important
Provides necessary information to explain a task.

AirHarmony-4200 DC (Internal Filters) Installation Guide
UGD-D01196 Airspan Commercial and Internal Use 14
Convention
Element
Note
Provides additional information.
Tip
Provides helpful hints.
Document Organization
Chapter
Contents
Introduction
Provides a comprehensive overview of AirHarmony-4200 DC Internal
Filters and its installation.
Getting Started
Provides workflows for initial install and workflow.
Verifying Prerequisites
Lists the hardware, software, and client requirements for
installation.
AirHarmony-4200 DC Internal Filters Installation
Describes how to install AirHarmony-4200 DC Internal Filters unit.
GPS Installation
Describes how to install the GPS antenna.
Connect and Manage Cables
Describes how to connect the cables.
Job Sheet
Provides information that aids users in performing the installation.
Abbreviations
Lists the abbreviations used in this document and their expansions.
Related Reading
The following documents contain related information:
AirHarmony-4200 Hardware Product Specification
Airspan LTE Commissioning Manual