Airspan AirHarmony-1000 User manual

AirHarmony-1000 Installation Guide
Part Number: UGD-D01006
System Release: 14.1
Revision: A4
Published: August 2015

© Copyright by Airspan Networks Inc., 2015. All rights reserved worldwide.
Legal Notices
The information contained within this document is proprietary and is subject to all relevant copyright, patent and other laws
protecting intellectual property, as well as any specific agreements protecting Airspan Networks Inc. rights in the aforesaid
information. Neither this document nor the information contained herein may be published, reproduced or disclosed to third
parties, in whole or in part, without the express, prior, written permission of Airspan Networks Inc. In addition, any use of this
document or the information contained herein for the purposes other than those for which it is disclosed is strictly forbidden.
Airspan Networks Inc. reserves the right, without prior notice or liability, to make changes in equipment design or specifications.
Information supplied by Airspan Networks Inc. is believed to be accurate and reliable. However, no responsibility is assumed by
Airspan Networks Inc. for the use thereof nor for the rights of third parties which may be effected in any way by the use of
thereof.
Any representation(s) in this document concerning performance of Airspan Networks Inc. product(s) are for informational
purposes only and are not warranties of future performance, either expressed or implied. Airspan Networks Inc. standard
limited warranty, stated in its sales contract or order confirmation form, is the only warranty offered by Airspan Networks Inc. in
relation thereto.
This document may contain flaws, omissions or typesetting errors; no warranty is granted nor liability assumed in relation
thereto unless specifically undertaken in Airspan Networks Inc. sales contract or order confirmation. Information contained
herein is periodically updated and changes will be incorporated into subsequent editions. If you have encountered an error,
please notify Airspan Networks Inc. All specifications are subject to change without prior notice.
Product performance figures quoted within this document are indicative and for information purposes only.
Acknowledgements
© Intel Corporation http://www.intel.com/
© Microsoft Corporation http://www.microsoft.com

UGD-D01006 Airspan Commercial and Internal Use i
Table of Contents
Document Information.............................................................................1
Abstract..................................................................................................................1
Revision History.....................................................................................................1
Warnings and Cautions...........................................................................2
Human Exposure to Radio Frequencies ................................................................2
Radio Interference .................................................................................................2
Avoiding Radio Interference...................................................................................2
Modifications..........................................................................................................2
General..................................................................................................................2
Safety.....................................................................................................................2
Warning of Hazardous Voltages ............................................................................3
Adherence to European Directive 1999/519/EC ....................................................3
Warning Symbols...................................................................................................3
Service Information................................................................................................4
UL Information .......................................................................................................4
Lightning Protection ...............................................................................................4
DECLARATION OF CONFORMITY........................................................5
GPS Compliance ...................................................................................................6
Maximum Output TX Power....................................................................7
Power Consumption...............................................................................................7
Antenna System.....................................................................................................7
Front Mounted Sector Antenna..............................................................................7
SelectaBeam Multi-beam Antenna.........................................................................8
AirHarmony-1000 Antenna Usage Options............................................................8
About This Document ...........................................................................10
Purpose................................................................................................................10
Intended Audience...............................................................................................10
Document Conventions........................................................................................10
Document Organization .......................................................................................11
Related Reading ..................................................................................................11

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use ii
Customer Care Help Desk....................................................................12
Airspan Encourages Comments ..........................................................................12
1Introduction.......................................................................................13
1.1 AirHarmony-1000..........................................................................................13
1.1.1 Deployment..................................................................................................13
2Getting Started..................................................................................15
2.1 Workflow of Installation .................................................................................15
2.2 AirHarmony-1000 Installation Checklist.........................................................16
3Verifying Prerequisites ......................................................................17
3.1 Verifying Site Requirements..........................................................................17
3.2 Verify Installation Requirements....................................................................17
3.2.1 Verify the Tools............................................................................................17
3.2.2 Verify the Parts and Kits...............................................................................17
3.2.3 Power Supply...............................................................................................19
3.2.4 Verify Components.......................................................................................19
3.2.5 Physical Dimensions....................................................................................22
3.2.6 Environmental..............................................................................................23
4Before Installation of AirHarmony-1000.............................................24
4.1 Connection of GPS Antenna .........................................................................24
4.2 Weather-proofing of the Antenna Connections .............................................24
5Installing AirHarmony-1000...............................................................26
5.1 Pole Mount Assembly....................................................................................26
5.1.1 Installing AirHarmony-1000 Back-to-Back....................................................29
5.2 Wall Mount Assembly....................................................................................30
5.3 Securing AirHarmony-1000 to the Mounting Plate ........................................32
5.4 Front Mount Antenna Tilt Adjustment............................................................33
5.5 LED Display ..................................................................................................34
5.6 Connecting the Ground Cable.......................................................................34
5.7 Installing AC/DC Converter ...........................................................................36
5.7.1 AC/DC Converter Pole Mount Assembly......................................................36
5.7.2 AC/DC Converter Wall Mount Assembly ......................................................37
6Cable Connections............................................................................39

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use iii
6.1 Connecting the AC/DC Power Converter to AirHarmony-1000.....................39
6.1.1 Power Cable Preparation .............................................................................39
6.2 Wiring AC Power Cable on the AC/DC Converter.........................................41
6.3 Wiring AC Power Input Cable........................................................................43
6.4 Fiber Ethernet (SFP) Cable Installation.........................................................44
6.4.1 SFP Cable Connection.................................................................................44
6.5 Copper Ethernet Cable Installation................................................................46
6.5.1 Hardware Requirements ..............................................................................46
6.5.2 Tool Requirements.......................................................................................47
6.5.3 Assembly Instructions ..................................................................................47
7Additional Installations (Non-Standard).............................................50
7.1 Front Antenna Assembly...............................................................................50
7.2 Connecting RF Jumper Cables to External Antenna.....................................50
AJob Sheet..........................................................................................52
BChecklist ...........................................................................................53
CAbbreviations ....................................................................................54
Figures
Figure 1: AirHarmony-1000 with front mounted antenna and AirHarmony-1000 with sun-shield ..........9
Figure 2: AirHarmony-1000 assembled with Front Mount antenna and GPS ......................................14
Figure 3: Workflow................................................................................................................................15
Figure 4: AirHarmony-1000 Unit, bottom termination ...........................................................................22
Figure 5: AirHarmony-1000 Unit, Top, RF ports...................................................................................22
Figure 6: Attaching GPS antenna to unit ..............................................................................................24
Figure 7: Verify connection of RF cable................................................................................................25
Figure 8: Weather-proof the connection ...............................................................................................25
Figure 9: Pole mounting assembly preparation ....................................................................................26
Figure 10: Mounting plate on pole ........................................................................................................27
Figure 11: Assemble clamp bands (4 required)....................................................................................27
Figure 12: Press down locking mechanism ..........................................................................................27
Figure 13: Tighten clamp bands ...........................................................................................................28
Figure 14: Pole mounting –exploded view...........................................................................................28
Figure 15: Mounted on pole..................................................................................................................29

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use iv
Figure 16: Back-2-Back Assembly........................................................................................................30
Figure 17: Positioning wall mounting plate ...........................................................................................31
Figure 18: Wall mounting plate fastened on wall..................................................................................31
Figure 19: Lift unit to top of mounting plate...........................................................................................32
Figure 20: unit engages into slots on the top of mounting plate...........................................................32
Figure 21: AirHarmony-1000 unit engaged into the bottom slots .........................................................33
Figure 22: Tilt adjustment body.............................................................................................................33
Figure 23: Tilt adjustment antenna .......................................................................................................34
Figure 24: Attaching ground cable to AirHarmony-1000.......................................................................35
Figure 25: attach ground cable to pole (example) ................................................................................35
Figure 26: Assemble clamp bands (2 required)....................................................................................36
Figure 27: Press down locking mechanism ..........................................................................................36
Figure 28: Tighten clamp bands ...........................................................................................................37
Figure 29: Pole mounting –exploded view...........................................................................................37
Figure 30: Wall mount –exploded view................................................................................................38
Figure 31: Wall mount...........................................................................................................................38
Figure 32: AC/DC Converter with DC power connector .......................................................................39
Figure 33: DC Power connector pre-assembled on converter..............................................................39
Figure 34: Power connection - on bottom panel of AirHarmony-1000..................................................40
Figure 35: Power cable assembly.........................................................................................................40
Figure 36: Power cable attached to AirHarmony-1000.........................................................................40
Figure 37: Waterproof connector exploded view ..................................................................................41
Figure 38: AC power cable preparation ................................................................................................41
Figure 39: Waterproof connector separated .........................................................................................41
Figure 40: Connector on cable..............................................................................................................41
Figure 41: Secure cable to connector...................................................................................................42
Figure 42: Power cable wires assembled.............................................................................................42
Figure 43: Numbered connector contacts.............................................................................................42
Figure 44: Assemble and tighten ..........................................................................................................43
Figure 45: AC/DC converter cable connector assembly.......................................................................43
Figure 46: AC/DC converter wires assembled......................................................................................43
Figure 47: Assemble and tighten ..........................................................................................................43
Figure 48: Connector assembled and tightened...................................................................................44
Figure 49: LC duplex cable assembly...................................................................................................44
Figure 50: Cable connector hook up to the board connector................................................................45
Figure 51: Slide on inner housing .........................................................................................................45
Figure 52: Slide over and click..............................................................................................................46
Figure 53: Ethernet cable thru connector..............................................................................................47
Figure 54: Ethernet cable stripped........................................................................................................48
Figure 55: RJ45 wire positioning...........................................................................................................48

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use v
Figure 56: cable trimmed ......................................................................................................................48
Figure 57: RJ45 plug assembly ............................................................................................................48
Figure 58: RJ45 crimping......................................................................................................................49
Figure 59: Crimped cable......................................................................................................................49
Figure 60: RJ45 assembled..................................................................................................................49
Figure 61: Attaching front mount antenna assembly to AirHarmony-1000...........................................50
Figure 62: Connecting RF cable ...........................................................................................................51
Figure 63: Weather-proof the connection .............................................................................................51
Tables
Table 1: AirHarmony-1000 FCC Maximum Output TX Power................................................................7
Table 2: AirHarmony-1000 ETSI Maximum Output TX Power ...............................................................7
Table 3: Power Consumption..................................................................................................................7
Table 4: Front Mounted Sector Antenna Parameters.............................................................................8
Table 5: Omni Antenna Parameters .......................................................................................................8
Table 6: Typographic Conventions .......................................................................................................10
Table 7. Minimum Hardware Requirements .........................................................................................17
Table 8. Parts & Kits .............................................................................................................................17
Table 9: AirHarmony-1000 additional items..........................................................................................19
Table 10: AirHarmony-1000 Components ............................................................................................20
Table 11. AirHarmony-1000 Physical Dimensions................................................................................22
Table 12. AirHarmony 1000 Environment Compliance.........................................................................23
Table 13: LED display...........................................................................................................................34
Table 14: Hardware...............................................................................................................................46
Table 15: Tools .....................................................................................................................................47

AirHarmony Installation Guide
UGD-D00105 Airspan Commercial and Internal Use 1
Document Information
Abstract
This document details procedures for installing the Airspan’s AirHarmony 1000 Indoor-Pico
Enterprise-Femto eNodeB variant.
Revision History
Revision Details
Date
Summary of Changes
Rev 0.1
October 2014
Initial document
Reformatted and revised the document.
Rev A + A1
November 2014
Updates
Rev A2 +A3
February 2015
B2B mounting option
Updates
Rev A4
August 2015
Additional Antenna
Additional content

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 2
Warnings and Cautions
Human Exposure to Radio Frequencies
The AirHarmony-1000 antennas should be installed and operated from a minimum safe distance of:
AirHarmony-1000 with Front Mount Antenna: 2.5m
AirHarmony-1000 with External Antenna: 2.5m
AirHarmony-1000 with Smart Beam Antenna (SBA): 0.5m (pending)
Radio Interference
This AirHarmony-1000 generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment on and off, the technician is encouraged to try to correct
the interference by performing one or more of the following measures:
Re-orientate or relocate the unit
Increase separation between the eNodeBs and/or End Device
Connect the equipment to an outlet on a circuit different from that to which the power source
is connected
Avoiding Radio Interference
Ensure a minimum of 1-meter separation between co-located AirHarmony 1000 units.
Modifications
Any changes and modifications to this device that are not expressly approved by Airspan Networks
may void the user's authority to operate the equipment.
General
Only qualified personnel should be allowed to install, replace, and service the equipment.
The device cannot be sold retail, to the general public or by mail order. It must be sold to
operators.
Installation must be controlled.
Installation must be performed by licensed professionals.
Installation requires special training. The AirHarmony-1000 radio and antenna should be
installed ONLY by experienced installation professionals who are familiar with local building
and safety codes and, wherever applicable, are licensed by the appropriate government
regulatory authorities. Failure to do so may void Airspan's product warranty and may expose
the end user or the service provider to legal and financial liabilities. Airspan and its resellers
or distributors are not liable for injury, damage or violation of regulations associated with the
installation of outdoor units or antennas.
The device is to be installed in a Restricted Access Location.
Safety
1. Read this guide and follow all operating and safety instructions.
2. Keep all product information for future reference.

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 3
3. This product is supplied with a grounding connection which must be connected. Do not
defeat this important safety feature.
4. Static sensitive components inside - do not remove the lid or base: No user serviceable
parts inside.
5. Position the power cord to avoid possible damage; do not overload wall outlets.
6. Do not place this product on or near a direct heat source, and avoid placing objects on
the terminal.
7. To avoid electrical shock do not install this device during adverse conditions such as rain
or inclement weather.
8. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the
power before cleaning.
9. The units should not be located too near power lines or other electrical power circuits,
where it can come into contact with such power lines or circuits.
10. The radio transceiver must be properly grounded to protect against power surges and
accumulated static electricity. It is the user’s responsibility to install this device in
accordance with the local electrical codes.
11. Installation of the AirHarmony-1000 must be contracted to a professional installer.
12. Disconnect Device. The socket outlet should be easily accessible in case you have to
disconnect the device.
13. When installed in the final configuration, the product must comply with the applicable
Safety Standards and regulatory requirements of the country in which it is installed. If
necessary, consult with the appropriate regulatory agencies and inspection authorities to
ensure compliance.
Warning of Hazardous Voltages
On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power.
Remove metal jewellery that could come into contact with AC power.
On DC sections, short-circuiting the low voltage, low impedance circuits can cause severe arcing that
may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits.
Note: Airspan products do not contain hazardous substances (as defined in UK Control of
Substances Hazardous to Health Regulations 1989 and the Dangerous Substances Regulations
1990). At the end of any Airspan products life cycle, the customer should consult with Airspan to
ensure that the product is disposed of in conformance with the relevant regulatory requirements.
Adherence to European Directive 1999/519/EC
European Council Recommendation 1999/519/EC details basic restrictions and reference levels on
human exposure to electromagnetic fields as advised by the ICNIRP. Adherence to these
recommended restrictions and reference levels should provide a high level of protection as regards
the established health effects that may result from exposure to electromagnetic fields.
Warning Symbols
The following symbols may be encountered during installation or troubleshooting. These warning
symbols mean danger. Bodily injury may result if you are not aware of the safety hazards involved in
working with electrical equipment and radio transmitters. Familiarize yourself with standard safety
practices before continuing.
Electro-Magnetic Radiation
High Voltage

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 4
Service Information
Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void
the warranty.
Disconnect the power to this product and return it for service if the following conditions apply:
a. The terminal does not function after following the operating instructions outlined in this
manual.
b. Liquid has been spilled, a foreign object is inside, or the terminal has been exposed to
rain.
c. The product has been dropped or the housing is damaged.
Locate the serial number of the terminal and record this on your registration card for future reference.
Also record the MAC address, located on the product sticker.
UL Information
- The equipment must be properly grounded according with NEC and other local safety code
requirements.
- Reminder to all the BWA system installers: Attention to Section 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected
to the grounding system of the building, as close to the point of cable entry as is practical.
- AirHarmony-1000 is designed to operate in environmental conditions complying with IP66 and
relevant standards.
Lightning Protection
WARNING: The following notes are general recommendations for the system. The wireless
equipment should be installed by a qualified professional installer and must follow local and national
codes for electrical grounding and safety. Failure to meet safety requirements and/or use of non-
standard practices and procedures could result in personal injury and damage to equipment. A direct
lightning strike may cause serious damage even if these guidelines are followed.
All outdoor wireless equipment is susceptible to lightning damage from a direct hit or induced current
from a near strike. Lightning protection and grounding practices in local and national electrical codes
serve to minimize equipment damage, service outages, and serious injury. The antennas are to be
DC grounded, so surge protection is not required. Reasons for lightning damage are summarized as:
- Poorly grounded tower/antenna sites that can conduct high lightning strike energy into equipment.
- Lack of properly installed lightning protection equipment that can cause equipment failures from
lightning induced currents.
A lighting protection system provides a means by which the energy may enter earth without passing
through and damaging parts of a structure. A lightning protection system does not prevent lightning
from striking; it provides a means for controlling it and preventing damage by providing a low
resistance path for the discharge of energy to travel safely to ground. Improperly grounded
connections are also a source of noise that can cause sensitive equipment to malfunction.
A good tower grounding system disperses most of the surge energy from a tower strike away from the
building and equipment.
To limit the equipment damage due to a lightning strike, the following practices are recommended for
the wireless system:
- Provide direct grounding from the antenna mounting bracket, the radio and antenna and the
lightning/surge protectors to the same ground point at the base of the tower or a ground bus on the
building. Use the grounding screws on the antenna bracket and the radio and antenna for terminating
the ground wires.
- The AC wall outlet ground must be connected to the same grounding system as the eNodeB.

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 5
DECLARATION OF CONFORMITY
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Deutsch:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden
Vorgaben der Richtlinie 1999/5/EU.
Dansk:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i
Directiv 1999/5/EF.
Español:
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directive
1999/5/EC.
Greek:
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Airspan ΔΗΛΩΝΕΙ ΟΤΙ Ο ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français:
Cet appareil est conforme aux exigencies essentialles et aux autres dispositions pertinantes de la
Directive 1999/5/EC.
Íslenska:
Þessi búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipunar 1999/5/ESB.
Italiano:
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva
1999/5/EC.
Nederlands:
Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijn
1999/5/EC.
Norsk:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-
directiv 1999/5/EC.
Português:
Este equipamento satisfaz os requisitos essenciais e outras provisões da Directiva 1999/5/EC.
Suomalainen:
Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimukset ja on siinä asetettujen muidenkin
ehtojen mukainen.
Svenska:
Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta
bestämmelser i Direktiv 1999/5/EC.
Român:
Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale Directivei
1999/5/CE.
The Declaration of Conformity related to this product can be obtained from [email protected].

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 6
GPS Compliance
The GPS is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC."
The GPS complies with the following EMC Common Regulatory Testing standards:
EN55022: Radiated and Conducted Emissions
CISPR 22: Class B
EN 50081-1: Generic Emissions Class B
EN 50082-1: Generic Immunity Class B
EN 61000-4-2: Electrostatic Discharge Immunity
EN 61000-4-3: Radiated RF EM Field Immunity Test
EN 61000-4-4: Electrical Fast Transient/Burst Test
EN 61000-4-6: Conducted Immunity
EN 61000-4-8: Magnetic Field Immunity
Note: A GPS is recommended for synchronizing between LTE sectors.
Note: An optional GPS Lightning/Surge protector is available from Airspan when installing the GPS
antenna in a remote location for lightning prone deployments.

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 7
Maximum Output TX Power
Table 1: AirHarmony-1000 FCC Maximum Output TX Power
Frequency Band
FCC
TX EIRP
Antenna Gain
2300-2400 MHz
TBDdBm
TBDdBM
12dBi
2496-2 690 MHz
39.86dBm
57.86dBm
18dBi
Table 2: AirHarmony-1000 ETSI Maximum Output TX Power
Frequency Band
ETSI
TX EIRP
Antenna Gain
2300-2400 MHz
40dBm
52dBm
12dBi
2496-2 690 MHz
40dBm
58dBm
18dBi
Caution: Do not set maximum output TX power to higher than local regulations.
Power Consumption
AirHarmony-1000 has a Max nominal power consumption of 130W. AirHarmony-1000 power
consumption is described in the following table:
Table 3: Power Consumption
Duplex
Tx Power at RF
Port (dBm)
Nominal Power
Consumption (W)
Power Supply Requirement (W)
FDD
TBD
TBD
TBD
TDD
37
156
200
Antenna System
The following antennas are designed specifically for AirHarmony-1000 deployments. Externally
mounted antennas are available for use as well (pending), but are specified separately.
Note: For a list of compatible external antennas, please contact your nearest Airspan sales
representative.
Front Mounted Sector Antenna
The front mounted sector antenna is a cross polarized fixed antenna which mounts on the front of the
unit in place of the sun-shield.

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 8
Note: When using a front mounted antenna, external antennas cannot be used.
Note: When using external antennas, the sun-shield must be used.
Table 4: Front Mounted Sector Antenna Parameters
Parameter
2.x GHz
3.x GHz
Frequency
2.3–2.7
2.3–2.7
3.3–3.8
Polarization
Dual Slant ±45
Dual Slant ±45
Dual Slant ±45
Polarization discrimination
18 dB
15 dB
>15 dB
Boresight gain
12 dBi
7.5 dBi
11.5 dBi
Azimuth HPBW
65
90± 10
65
Elevation HPBW
22
20
22
Electrical tilt
-1
N/A
-1
Grounding
DC GND
DC GND
DC GND
SelectaBeam Multi-beam Antenna
The SelectaBeam SC-800 provides four direction beams and an omnidirectional pattern covering
360in azimuth. Beam selection is achieved via a digital control interface.
Table 5: Omni Antenna Parameters
Parameter
2.x GHz
Frequency
2.3–2.7
Polarization
Dual Slant ±45
Polarization discrimination
16 dB
Boresight gain
2.0 dBi
Peak gain
7.5 dBi
Azimuth HPBW
Omni-Directional
Elevation HPBW
20
Electrical tilt
N/A
Grounding
DC GND
AirHarmony-1000 Antenna Usage Options
AirHarmony-1000 comes in arange of frequency variants that can be mounted with different
antenna options and formats. Initially deliveries are of the Front Mount Antenna variant.
A typical sector installation will have a cross-polar sector antenna fitted directly to the front of the
AirHarmony-1000 main unit. (This is attached instead of the sun-shield in other variants - pending).

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 9
Figure 1: AirHarmony-1000 with front mounted antenna and AirHarmony-1000 with sun-shield

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 10
About This Document
Purpose
This guide provides the workflow and step-by-step procedures for Installing the AirHarmony-1000.
These procedures include:
Verify prerequisites
Install wall / pole mount
Install the AirHarmony-1000
Install the AC/DC converter
Connect and manage cables
Intended Audience
This guide is intended for persons who are responsible for installing the AirHarmony-1000 equipment.
These persons should have aworking knowledge of the equipment.
Document Conventions
This document uses the following typographic conventions.
Table 6: Typographic Conventions
Convention
Element
Blue underlined text
Cross-reference links.
Bold text
Keyboard buttons and GUI elements.
Command
Command names or phrases.
Computer output
Text displayed by the computer.
Hyperlinks
Website and e-mail addresses.
Danger
Signifies a hazardous situation—if not avoided—will
cause death or serious injury. Describes how to avoid
it.
Warning
Signifies a hazardous situation—if not avoided—can
cause death or serious personal injury. Describes
how to avoid it.
Caution
Signifies a hazardous situation—if not avoided—can
void the product warranty, and cause property
damage. Describes how to avoid it.
Important
Provides necessary information to explain a task.
Note
Provides additional information.
Tip
Provides helpful hints.

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 11
Document Organization
Chapter
Contents
Introduction
Provides a comprehensive overview of AirHarmony 1000 and
its installation.
Getting Started
Provides workflows for initial install and workflow.
Verifying Prerequisites
Lists the hardware, software, and client requirements for
installation.
AirHarmony-1000 Installation
Describes how to install AirHarmony-1000.
Install the AC/DC converter
AC/DC converter installation
Connect and Manage Cables
Describes how to connect the cables.
Job Sheet
Provides information that aids users in performing the
installation.
Checklist
Provides an overview of the high–level steps involved in the
workflow.
Abbreviations
Lists the abbreviations used in this document and their
expansions.
Related Reading
The following documents contain related information:
AirHarmony-1000 Hardware Product Specification
AirHarmony-1000 Commissioning Manual

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 12
Customer Care Help Desk
Airspan’s Customer Care Help Desk offers prompt and efficient customer support services.
Note: To avail Airspan’s Customer Care Help Desk support, you must be a registered user and
must have a valid support contract. To register, click here and fill the Registration form.
To create and update issue logs, send e-mails to Customer Care Help Desk. Once you submit your
issue, the system generates a new issue and sends an issue number for your reference. The system
uses this issue number to categorize and store e-mails under the appropriate issue.
To help Customer Care Help Desk identify your issue, include the issue number and your Customer
Care Helpdesk account details in all further communications.
Main Operations
Airspan Communications Ltd.
Capital Point
33 Bath Road
Slough, Berkshire
SL1 3UF, United Kingdom
Tel: [phone]
Worldwide Headquarters
Airspan Networks Inc.
777, Yamato Road, Suite 105
Boca Raton, FL 3341-4408, USA
Tel: [phone]
Airspan Encourages Comments
Airspan welcomes any feedback and suggestions that help to improve the quality of the
documentation. Send your feedback to [e-mail].

AirHarmony-1000 Installation Guide
UGD-D01006 Airspan Commercial and Internal Use 13
1 Introduction
This section provides a descriptive overview of the Airspan’s AirHarmony-1000 Micro / Pico eNodeB
variant and its place in the Airspan product suite.
1.1AirHarmony-1000
AirHarmony-1000 is part of Airspan’s carrier-class 4G Micro eNodeB family. AirHarmony-1000
supports 3GPP’s Long Term Evolution (LTE) eNodeB specifications, providing high-speed data and
mobility in order to meet the demands of the Broadband Wireless Access market.
AirHarmony-1000 is a compact, easy to install Micro / Pico-cell, allowing an operator to deploy LTE
broadband services using existing Street Furniture (e.g. street lamps, power poles, etc…)
AirHarmony-1000 employs Software Defined Radio (SDR) technology, together with two transmit and
receive paths, antennas and a GPS receiver - all in a highly integrated, physically small and light, All-
Outdoor package, targeted to blend seamlessly into the urban environment. This very compact
outdoor product minimizes physical footprint, power consumption and operator OPEX.
AirHarmony-1000 will support a wide array of frequencies and channel sizes, able to operate in both
licensed and unlicensed bands. Frequencies and channel sizes will be added regularly.
AirHarmony-1000 implements dual 37 dBm (2 x 5W) transmitters with the availability of several
optional integral antennas and external antennas connectivity.
AirHarmony-1000 fully supports the standard LTE (Uu/S1/X2) interfaces.
All Airspan eNodeB products, including AirHarmony-1000, are interoperable with a rich portfolio of 3rd
party end user devices, including many handsets, indoor UEs, outdoor UEs and USB dongles from
several ODMs, using various chipsets. For an updated of interoperability list, please contact your
nearest Airspan Sales Representative.
Note: For management please refer to the AirHarmony-1000 LTE Commissioning Manual as well
as the Netspan User Manual.
1.1.1 Deployment
A highly flexible and scalable 4G Base Station, the AirHarmony-1000 is capable of supporting LTE
profiles across multiple frequency bands.
Note: The following is for illustration only; actual layout may differ as infrastructure is installation-
specific.
Note: AirHarmony-1000 must be properly grounded according with NEC and other local safety
code requirements.