Airspan AirSpeed 1030 B48 User manual

AirSpeed 1030 B48 Installation Guide
Part Number: DUG01623
System Release: 17.5
Revision: A1
Published: August 2020

© Copyright by Airspan Networks Ltd., 2020. All rights reserved worldwide.
Legal Notices
The information contained within this document is proprietary, privileged and intended only for the recipient. As
such, the information is subject to all relevant copyright, patent and other laws protecting intellectual property, as
well as any specific agreements protecting Airspan Networks Ltd. rights in the aforesaid information. Neither this
document nor the information contained herein may be published, reproduced, transmitted or disclosed to third
parties, in whole or in part, without the express, prior, written permission of Airspan Networks Ltd. In addition, any
use of this document or the information contained herein for the purposes other than those for which it is disclosed
is strictly forbidden.
Airspan Networks Ltd. reserves the right, without prior notice or liability, to make changes in equipment design or
specifications.
Information supplied by Airspan Networks Ltd. is believed in good faith to be accurate and reliable, while every
care has been taken in preparing these documents. However, Airspan Networks Ltd. does not make any
representations and gives no warranties of whatever nature in respect of these documents, including without
limitation, the accuracy or completeness of any information, facts and/or opinions contained therein. No
responsibility is assumed by Airspan Networks Ltd. for the use of the documents nor for the rights of third parties
which may be effected in any way by the use thereof. The provision of these documents (and the documents
themselves) does not constitute professional advice of any kind. Any representation(s) in these documents
concerning performance of Airspan Networks Ltd. product(s) are for informational purposes only and are not
warranties of future performance, either expressed or implied. Airspan Networks Ltd., its affiliates, directors,
employees and agents shall not be held liable for any damages or losses, of any nature whatsoever, arising from
any use of and/or reliance on the documents.
These documents may contain flaws, omissions or typesetting errors; no warranty is granted nor liability assumed
in relation thereto unless specifically undertaken in Airspan Networks Ltd. sales contract or order confirmation.
Information contained herein is periodically updated and changes will be incorporated into subsequent editions. If
you have encountered an error, please notify Airspan Networks Ltd.
Product performance figures quoted within this document are indicative and for information purposes only.
UK WEEE Registration number: WEEE/AB0207WZ. For more information, see WEEE Information for Airspan
Customers and Recyclers.
Acknowledgements
© Intel Corporation http://www.intel.com/
© Microsoft Corporation http://www.microsoft.com

AirSpeed 1030 B48 Installation Guide
DUG01610 Airspan Commercial and Internal Use 1
Table of Contents
Document Information..............................................................................5
Abstract..................................................................................................................5
Revision History.....................................................................................................5
Warnings and Cautions............................................................................6
Human Exposure to Radio Frequencies ................................................................6
Avertissement et Precautions d’Utilisation ...............................................6
Exposition des personnes aux fréquences radioélectriques ..................................6
Radio Interference .................................................................................................6
Modifications..........................................................................................................6
General..................................................................................................................6
Général..................................................................................................................6
Important Safety Instructions............................................................................7
Safety.....................................................................................................................7
Securite..................................................................................................................7
Warning of Hazardous Voltages ............................................................................8
Attention aux Voltages Hasardeux.........................................................................8
Adherence to European Directive 2014/53/EU ......................................................8
Warning Symbols...................................................................................................8
Service Information................................................................................................8
UL Information .......................................................................................................9
DECLARATION OF CONFORMITY ........................................................9
Maximum Output TX Power...................................................................11
Product Variants ..................................................................................................11
Power Consumption.............................................................................................12
External Antennas (Optional)...............................................................................13
About This Document.............................................................................14
Purpose................................................................................................................14
Intended Audience...............................................................................................14
Document Conventions........................................................................................14

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 2
Related Reading..................................................................................................15
Customer Care Help Desk.....................................................................16
Airspan Encourages Comments ..........................................................................16
1Introduction.........................................................................................17
1.1 AirSpeed 1030 B48.......................................................................................17
2Getting Started ...................................................................................18
2.1 Workflow of Installation .................................................................................18
2.2 AirSpeed 1030 B48 Installation Checklist......................................................18
3Verifying Prerequisites .......................................................................19
3.1 Verifying Site Requirements..........................................................................19
3.2 Verify Installation Requirements....................................................................19
3.2.1 Verify the Tools.............................................................................................. 19
3.2.2 Verify the Parts and Kits ................................................................................ 20
3.2.3 Power Supply................................................................................................. 21
3.2.4 Connections................................................................................................... 21
3.2.5 Physical Dimensions...................................................................................... 23
3.2.6 Environmental................................................................................................ 23
3.3 LEDs Display.................................................................................................24
4AirSpeed 1030 B48 Installation..........................................................25
4.1 Back Bracket Assembly.................................................................................25
4.2 Connecting the GPS Antenna.......................................................................26
4.3 Weather-proofing Antenna Connections .......................................................26
4.4 Pole Mounting Assembly...............................................................................27
4.5 Wall Mount Assembly....................................................................................29
4.6 Tilt Adjustment ..............................................................................................30
5Connect and Manage Cables.............................................................31
5.1 Grounding .....................................................................................................31
5.2 Fiber Ethernet (SFP) Cable Preparation .......................................................31
5.3 Copper Ethernet Cable Preparation..............................................................35
5.4 DC Cable Preparation...................................................................................38
5.5 Remote (External) Antenna Assembly ..........................................................42

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 3
AJob Sheet...........................................................................................44
BChecklist.............................................................................................45
CAbbreviations......................................................................................46
Figures
Figure 1: AirSpeed 1030 B48 (GPS Attached) .....................................................................................13
Figure 2: AirSpeed 1030 B48 Front View .............................................................................................17
Figure 3: Workflow................................................................................................................................18
Figure 4: AirSpeed 1030 B48 Top Ports...............................................................................................21
Figure 5: AirSpeed 1030 B48 Bottom Ports..........................................................................................22
Figure 6: Back Bracket Assembly.........................................................................................................25
Figure 7: Attaching GPS Antenna.........................................................................................................26
Figure 8: Pole Mounting Assembly.......................................................................................................27
Figure 9: Mounted on Pole....................................................................................................................28
Figure 10: AirSpeed on Wall.................................................................................................................29
Figure 11: Tilt Adjustment.....................................................................................................................30
Figure 12: Ground Connection..............................................................................................................31
Figure 13: Pre-assembled LC Duplex Cable ........................................................................................31
Figure 14: Open Housing Lock.............................................................................................................32
Figure 15: Gland Nut on Cable.............................................................................................................32
Figure 16: Insert Tightening Cone on Cable.........................................................................................32
Figure 17: Insert Rubber Gland on Cable.............................................................................................32
Figure 18: Pass Cable thru Housing.....................................................................................................33
Figure 19: Insert Cable into Transceiver...............................................................................................33
Figure 20: Insert Holder over theTransceiver.......................................................................................33
Figure 21: Holder into Housing Base....................................................................................................33
Figure 22: Holder into Transceiver........................................................................................................34
Figure 23: Lift Lever..............................................................................................................................34
Figure 24: Insert Gland .........................................................................................................................34
Figure 25: Insert Cone ..........................................................................................................................34
Figure 26: Tighten Gland Nut................................................................................................................35
Figure 27: Secure Housing Lock...........................................................................................................35
Figure 28: Pre-assembled RJ45 Cable.................................................................................................35
Figure 29: Gland Nut on Cable.............................................................................................................36
Figure 30: Insert Tightening Cone on Cable.........................................................................................36
Figure 31: Insert Rubber Gland on Cable.............................................................................................36
Figure 32: Insert Housing onto Cable...................................................................................................36

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 4
Figure 33: Insert Holder onto RJ45.......................................................................................................37
Figure 34: Holder into Housing Base....................................................................................................37
Figure 35: Align RJ45 into Holder.........................................................................................................37
Figure 36: Lift Lever..............................................................................................................................37
Figure 37: Insert Gland .........................................................................................................................38
Figure 38: Tighten Gland Nut................................................................................................................38
Figure 39: Secure Housing Lock...........................................................................................................38
Figure 40: Stripping Dimensions (DC Cable)........................................................................................39
Figure 41: Open Housing Lock.............................................................................................................39
Figure 42: Seperate into Sections.........................................................................................................39
Figure 43: Insert Gland Nut...................................................................................................................40
Figure 44: Pass DC Cable Thru............................................................................................................40
Figure 45: Tighten Two (2) Set Screws ................................................................................................40
Figure 46: Tighten the Strap Clamp......................................................................................................40
Figure 47: Align Marks + Click in Place ................................................................................................41
Figure 48: Place Split Rubber Gland ....................................................................................................41
Figure 49: Place Tightening Cone on Split Gland.................................................................................41
Figure 50: Tighten gland Nut.................................................................................................................41
Figure 51: Secure Housing Lock...........................................................................................................42
Figure 52: Antenna RF Cables .............................................................................................................42
Figure 53: Connecting Antenna RF Cable............................................................................................43
Tables
Table 1: AirSpeed 1030 B48 ETSI Maximum Output TX Power ..........................................................11
Table 2: AirSpeed 1030 B48 FCC Maximum Output TX Power...........................................................11
Table 3: Supported Frequency Bands..................................................................................................11
Table 4: Power Consumption................................................................................................................12
Table 5: Typographic Conventions.......................................................................................................14
Table 6. Minimum Hardware Requirements .........................................................................................19
Table 7. Parts & Kits .............................................................................................................................20
Table 8. AirSpeed 1030 B48 Physical Dimensions ..............................................................................23
Table 9. AirSpeed 1030 B48 Environment Compliance .......................................................................23
Table 10: LED Display ..........................................................................................................................24
Table 11: ABBREVIATIONS & DEFINITIONS......................................................................................46

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 5
Document Information
Abstract
This document details procedures for installing the Airspan’s AirSpeed 1030 B48 Pico-class LTE
eNodeB variant.
Revision History
Revision Details
Date
Summary of Changes
Rev 0.1 –0.5
June 2020
Initial document –draft
comments
Rev A
June 2020
Published after comments
Rev A1
August 2020
Added antenna variants + CBRS Note

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 6
Warnings and Cautions
Human Exposure to Radio Frequencies
The AirSpeed 1030 B48 should be installed andoperated from a minimum safe distance of at least 24.8
in. (63 cm) and installed higher than 2 meters to prevent unauthorized access.
Avertissement et Precautions d’Utilisation
Exposition des personnes aux fréquences radioélectriques
Les AirSpeed 1030 B48 doivent être installée et utilisée de façon à garantir la distance minimale de
sécurité de 63Cm et installé à plus de 2 mètres pour empêcher tout accès non autorisé.
Radio Interference
This AirSpeed 1030 B48 generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio, television reception or WiFi AP, which can be
determined by turning the equipment on and off, the technician is encouraged to try to correct the
interference by performing one or more of the following measures:
Re-orientate or relocate the unit
Increase separation between the units and/or End Devices
Connect the equipment to an outlet on a circuit different from that to which the power source is
connected
Modifications
Any changes and modifications to this device that are not expressly approved by Airspan Networks
may void the user's authority to operate the equipment.
General
Only qualified personnel should be allowed to install, replace, and service the equipment.
The device cannot be sold retail, to the general public or by mail order. It must be sold to
operators.
Installation must be controlled.
Installation must be performed by licensed professionals.
Installation requires special training. The AirSpeed 1030 B48 should be installed ONLY by
experienced installation professionals who are familiar with local building and safety codes
and, wherever applicable, are licensed by the appropriate government regulatory authorities.
Failure to do so may void Airspan's product warranty and may expose the end user or the
service provider to legal and financial liabilities.
Airspan and its resellers or distributors are not liable for injury, damage or violation of
regulations associated with the installation of units or antennas.
Général
Seul le personnel qualifié peut être autorisé pour installer ou remplacer l’équipement ainsi
qu’effectuer les opérations de maintenance pour cet équipement.
L’équipement ne peut pas être vendu en grande distribution ou par commande via email à
destination du public. Il doit être vendu aux opérateurs de télécommunications.
Son installation doit être contrôlée
Son Installation doit être effectuée par des professionnels autorises.

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 7
Son installation requiert une formation spécifique du personnel. L’AirSpeed 1030 B48, radio
et antenne doit être installe UNIQUEMENT par des installateurs professionnels expérimentés
et ayant une connaissance des constructions locales et règles de sécurité, ainsi que, dès que
nécessaire, disposant d’un agreement des autorités gouvernementales de régulation. Toute
enfreinte a ces obligations peut annuler la garantie délivrée par Airspan pour ces produits et
peut exposer l’utilisateur final ou le fournisseur de services a des dommages légaux et
financiers.
Airspan et ses revendeurs ou ses distributeurs ne sont pas responsables des blessures,
dommages ou violations de la régulation en vigueur lies a l’installation du système ou des
antennes.
Important Safety Instructions
Read and Save these instructions
This Installation Guide contains instructions and warnings that should be followed during
installation, and operation.
Failure to follow these instructions could cause bodily injury and/or product failure
Safety
1. Read this guide and follow all operating and safety instructions.
2. No user serviceable parts inside.
3. Position the power cord to avoid possible damage; do not overload circuits.
4. Do not place this product on or near a direct heat source, and avoid placing objects on
the terminal.
5. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the
power before cleaning.
6. The units should not be located near power lines or other electrical power circuits.
7. It is the user’s responsibility to install this device in accordance with the local electrical
codes.
8. Installation of the AirSpeed 1030 B48 must be contracted to a professional installer.
9. The circuit breaker should be easily accessible in case you have to disconnect the
device.
10. When installed in the final configuration, the product must comply with the applicable
Safety Standards and regulatory requirements of the country in which it is installed. If
necessary, consult with the appropriate regulatory agencies and inspection authorities to
ensure compliance.
Securite
1. Lire attentivement ce guide et suivre les instructions d’utilisation et de sécurité.
2. Aucune pièce a l’intérieur est d’utilité pour l’utilisateur.
3. Positionner le cordon d’alimentation de façon à éviter des dommages potentiels. Ne pas
surcharger les circuits.
4. Ne pas placer ce produit sur ou à proximité d’une source directe de chaleur et éviter de
placer des objets sur le terminal.
5. Utiliser uniquement chiffon de coton pour nettoyage. Ne pas utiliser de produits liquides
ou d’aérosols. Déconnecter le produit de la source d’alimentation avant nettoyage.
6. L’unité ne doit pas être située trop près de lignes électriques ou autres circuits de
puissance, avec lesquels il pourrait entrer en contact.
7. L’utilisateur est tenu responsable de l’installation du produit conformément aux règles
électrique en vigueur localement.

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 8
8. L’installation de AirSpeed 1030 B48 doit être contractualisée avec un installateur
professionnel.
9. L’interrupteur de circuit électrique doit être facilement accessible afin de pouvoir
déconnecter l’équipement.
10. Lors de l’installation de la configuration finale, le produit doit être conforme aux Standards
de Sécurité en vigueur ainsi qu’aux exigences réglementaires du pays dans lequel il est
installé. Si nécessaire, consulter les agences règlementaires appropriées, ainsi que les
autorités chargées de l’inspection afin de garantir la conformité.
Warning of Hazardous Voltages
On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power.
Remove metal jewellery that could come into contact with AC power.
On DC sections, short-circuiting the low voltage, low impedance circuits can cause severe arcing that
may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits.
Note: Airspan products do not contain hazardous substances (as defined in UK Control of
Substances Hazardous to Health Regulations 1989 and the Dangerous Substances Regulations
1990). At the end of any Airspan products life cycle, the customer should consult with Airspan to
ensure that the product is disposed of in conformance with the relevant regulatory requirements.
Attention aux Voltages Hasardeux
Sur les installations de réseau électrique de type courant alternatif (CA), des voltages hasardeux
peuvent survenir. Garder une Attention particulière lors d’une vérification ou de travaux sur réseau
électrique CA. Retirer tous bijoux en métal qui pourraient entrer en contact avec l’alimentation ou le
réseau CA.
Sur les portions de réseau électrique de type courant continu (CC), un circuit basse impédance peut
causer de sérieux arcs électriques qui pourraient bruler ou endommager les yeux. Retirer bagues,
anneaux, montres etc… afin d’éviter les court-circuit sur le réseau CC.
Adherence to European Directive 2014/53/EU
European Council Recommendation 2014/53/EU details basic restrictions and reference levels on
human exposure to electromagnetic fields as advised by the ICNIRP. Adherence to these
recommended restrictions and reference levels should provide a high level of protection as regards
the established health effects that may result from exposure to electromagnetic fields.
Warning Symbols
The following symbols may be encountered during installation or troubleshooting. These warning
symbols mean danger. Bodily injury may result if you are not aware of the safety hazards involved in
working with electrical equipment and radio transmitters. Familiarize yourself with standard safety
practices before continuing.
Caution, hot surface
Caution
Electro-Magnetic
Radiation
DC
Service Information
Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void
the warranty.
Disconnect the power to this product and return it for service if the following conditions apply:

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 9
a. The terminal does not function after following the operating instructions outlined in this
manual.
b. Liquid has been spilled, a foreign object is inside, or the terminal has been exposed to
rain.
c. The product has been dropped or the housing is damaged.
Locate the serial number of the terminal and record this on your registration card for future reference.
Also record the MAC address, located on the product sticker.
UL Information
- The electrical source must be properly grounded according with NEC and other local safety code
requirements.
- AirSpeed 1030 B48 is designed to operate in environmental conditions complying with IP40 and
relevant standards.
DECLARATION OF CONFORMITY
Declaration of Conformity with Regard to the R&TTE Directive 2014/53/EU
Czech:
Airspan tímto prohlašuje, že tento přístroj je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 2014/53 / EU.
Danish:
Undertegnede, Airspan erklærer hermed, at følgende udstyrsenhed opfylder de væsentlige krav og
andre relevante krav i direktiv 2014/53 / EF.
Deutsch:
Hiermit erklärt Airspan, dass die Produkteinheit die grundlegenden Anforderungen und anderen
relevanten Bestimmungen der Richtlinie 2014/53 / EU erfüllt.
Estonian:
Käesolevaga kinnitab Airspan, et seadme seade vastab direktiivi 2014/53 / EL olulistele nõuetele ja
muudele kõnealuse direktiivi asjakohastele sätetele.
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU.
Español:
Por medio de este Airspan, declara que la unidad cumple con los requisitos esenciales y cualquier otra
disposición aplicable o exigible de la Directiva 2014/53 / UE.
Greek:
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ΠΡΟΔΙΑΓΡΑΦΗ, η Airspan ΔΗΛΩΝΕΤΑΙ ότι η μονάδα συμμορφώνεται με τις
ουσιώδεις απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 2014/53 / ΕE.
Français:
Airspan déclare par la présente que l'appareil est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 2014/53 / UE.
Italiano:
Con la presente Airspan dichiara che questa unità è conforme ai requisiti essenziali e alle altre
disposizioni pertinenti stabilite dalla direttiva 2014/53 / UE.
Latvian:

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 10
Ar šo Airspan paziņo, ka vienība atbilst Direktīvas 2014/53 / ES būtiskajām prasībām un citiem
attiecīgajiem noteikumiem;
Lithuanian:
Šis „Airspan“ pareiškia, kad šis įrenginys atitinka esminius Direktyvos 2014/53 / ES reikalavimus ir kitas
nuostatas.
Nederlands:
Airspan verklaart hierbij dat de apparaateenheid voldoet aan de essentiële vereisten en andere
relevante bepalingen van richtlijn 2014/53 / EU.
Maltese:
Hawnhekk, Airspan, tiddikjara li din l-unità tikkonforma mar-rekwiżiti essenzjali u dispożizzjonijiet
rilevanti oħra li jinsabu fid-Direttiva 2014/53 / UE.
Hungarian:
Alulírott, az Airspan kijelenti, hogy az egység megfelel a 2014/53 / EU irányelv vonatkozó alapvető
követelményeinek és egyéb követelményeinek.
Polish:
Niniejszym Airspan oświadcza, że urządzenie jest zgodne z zasadniczymi wymaganiami i innymi
odpowiednimi postanowieniami dyrektywy 2014/53 / UE.
Português:
Airspan declara que esta unidade está em conformidade com os requisitos essenciais e outras
disposições da Diretiva 2014/53 / UE.
Slovenian:
Airspan izjavlja, da je ta enota skladna z bistvenimi zahtevami in drugimi ustreznimi določbami Direktive
2014/53 / EU.
Slovak:
Airspan týmto vyhlasuje, že tento prístroj spĺňa základné požiadavky a všetky príslušné ustanovenia
Smernice 2014/53 / EÚ.
Suomalainen:
Airspan vakuuttaa täten, että laitteen tyyppi on direktiivin 2014/53 / EU olennaisten vaatimusten ja
muiden asiaankuuluvien säännösten mukainen.
Swedish:
Därmed intygar Airspan att denna enhet överensstämmer med de väsentliga egenskapskraven och
andra relevanta bestämmelser som anges i direktiv 2014/53 / EU.
Íslenska:
Airspan lýsir hér með yfir að þessi eining uppfylli grunnkröfur og aðrar kröfur tilskipunar 2014/53 / ESB.
Norsk:
Airspan erklærer herved at utstyrsenheten oppfyller grunnleggende krav og andre relevante krav i
direktiv 2014/53 / EU.
Român:
Airspan declarăm pe propria răspundere că produsul produsului respectă cerințele esențiale și alte
prevederi aplicabile din Directiva 2014/53 / UE.
The Declaration of Conformity related to this product can be obtained from [email protected].

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 11
Maximum Output TX Power
Table 1: AirSpeed 1030 B48 ETSI Maximum Output TX Power
Frequency Band
(MHz)
ETSI
TX (dBm) EIRP (dBm)
Antenna Gain
(dBi)
Variant
3550-3700
33
50
17
1030
Table 2: AirSpeed 1030 B48 FCC Maximum Output TX Power
Frequency Band
(MHz)
FCC
TX (dBm) EIRP (dBm)
Antenna Gain
(dBi)
Variant
3550-3700
27.36 @ 10MHz
29.42 @ 20MHz
44.86 @10MHz
46.92 @20MHz
17.5
1030
26.86 @ 10MHz
28.92 @ 20MHz
44.86 @10MHz
46.92 @20MHz
18
1030
24.36 @ 10MHz
26.42 @ 20MHz
44.86 @10MHz
46.92 @20MHz
20.5
1030
19.86 @ 10MHz
21.92 @ 20MHz
44.86 @10MHz
46.92 @20MHz
25
1030
Note: The AirSpeed 1030 requires operation using an Airspan FCC-specific version of Netspan
acting as a CBRS Domain Proxy.
Caution: Do not set maximum output TX total power to higher than local regulations.
Product Variants
AirSpeed supports the following frequency bands with the specific performance values:
Table 3: Supported Frequency Bands
LTE
Band
Variant
Downlink
Freq.
(MHz)
Uplink
Freq.
(MHz)
Tx / Rx
Conf.
Tx Power
per Port
(dBm)
Power
Source
48
AS103-U48-B03DP
3550-3700
3550-3700
2 x 2T2R
4x 33 (4x2W)
DC

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 12
Power Consumption
Table 4: Power Consumption
Power Source
Nominal Power Consumption
(W)
Max Nominal Power
Consumption (W)
DC
65
95
Note: Nominal Power Consumption (W) - refers to average power consumption over time.

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 13
External Antennas (Optional)
AirSpeed 1030 B48 can be connected to external antennas (if required) via four (4) N-Type female
connectors located at the top panel. The antenna should be mounted to its appropriate mounting
facility.
The supported antennas should be dual slant, cross polar, DC grounded antennas.
Note: For a list of compatible external antennas, please contact your nearest Airspan Sales
representative.
Figure 1: AirSpeed 1030 B48 (GPS Attached)

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 14
About This Document
Purpose
This guide provides the workflow and step-by-step procedures for installing the Airspan’s AirSpeed
1030 B48, Pico-class LTE eNodeB variant. These procedures include:
Verify prerequisites
Install Back bracket & Pole/Wall bracket
Install the AirSpeed 1030 B48
Connect and manage cables
Intended Audience
This guide is intended for persons who are responsible for installing the AirSpeed 1030
B48 equipment.
Document Conventions
This document uses the following typographic conventions.
Table 5: Typographic Conventions
Convention
Element
Blue underlined text
Cross-reference links.
Bold text
Keyboard buttons and GUI elements.
Command
Command names or phrases.
Computer output
Text displayed by the computer.
Hyperlinks
Website and e-mail addresses.
Danger
Signifies a hazardous situation—if not avoided—will
cause death or serious injury. Describes how to avoid it.
Warning
Signifies a hazardous situation—if not avoided—can
cause death or serious personal injury. Describes how to
avoid it.
Caution
Signifies a hazardous situation—if not avoided—can void
the product warranty, and cause property damage.
Describes how to avoid it.
Important
Provides necessary information to explain a task.
Note
Provides additional information.
Tip
Provides helpful hints.

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 15
Related Reading
The following documents contain related information:
AirSpeed 1030 B48 Product Datasheet
Airspan LTE Commissioning Manual

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 16
Customer Care Help Desk
Airspan’s Customer Care Help Desk offers prompt and efficient customer support services.
Note: To avail Airspan’s Customer Care Help Desk support, you must be a registered user and must
have a valid support contract. To register, click here and fill the Registration form.
To create and update issue logs, send e-mails to Customer Care Help Desk. Once you submit your
issue, the system generates a new issue and sends an issue number for your reference. The system
uses this issue number to categorize and store e-mails under the appropriate issue.
To help Customer Care Help Desk identify your issue, include the issue number and your Customer
Care Helpdesk account details in all further communications.
Main Operations
Airspan Communications Ltd.
Capital Point
33 Bath Road
Slough, Berkshire
SL1 3UF, United Kingdom
Tel: [phone]
Worldwide Headquarters
Airspan Networks Inc.
777, Yamato Road, Suite 105
Boca Raton, FL 3341-4408, USA
Tel: [phone]
Airspan Encourages Comments
Airspan welcomes any feedback and suggestions that help to improve the quality of the documentation.
Send your feedback to documentf[email protected].

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 17
1 Introduction
This section provides a descriptive overview of the Airspan’s AirSpeed 1030 B48 small cell eNodeB
variant and its place in the Airspan product suite.
1.1AirSpeed 1030 B48
AirSpeed 1030 B48 is part of Airspan’s carrier-class LTE Advanced outdoor small cell eNodeB family.
AirSpeed 1030 B48 provides high-speed data, mobility, Voice over LTE, and broadcast/multicast
services.
AirSpeed 1030 B48 is a super compact, easy to install eNodeB, allowing an operator to deploy LTE
broadband services on any Street Furniture, rooftop or building front.
AirSpeed 1030 B48 is a dual sector / carrier 2x2 MIMO product with integrated front antenna.
Note: For management please refer to the Airspan LTE Commissioning Manual as well as the
Netspan User Manual.
The AirSpeed 1030 B48 unit is displayed below.
Figure 2: AirSpeed 1030 B48 Front View

AirSpeed 1030 B48 Installation Guide
DUG01623 Airspan Commercial and Internal Use 18
2 Getting Started
2.1Workflow of Installation
The Workflow to install the AirSpeed 1030 B48 is displayed in the following diagram:
Figure 3: Workflow
2.2AirSpeed 1030 B48 Installation Checklist
Plan the installation of the AirSpeed 1030 B48 by using the Installation Checklist, which you can find as
a removable job aid in Appendix B for this guide.