Airspan AirSpeed 1050 B3 User manual

AirSpeed 1050 B3 Installation Guide
Part Number: DUG01593
System Release: 16.5
Revision: A
Published: December 2020

© Copyright by Airspan Networks Inc., 2020. All rights reserved worldwide.
Legal Notices
The information contained within this document is proprietary, privileged and intended only for the recipient. As such, the
information is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any specific
agreements protecting Airspan Networks Ltd. rights in the aforesaid information. Neither this document nor the information
contained herein may be published, reproduced, transmitted or disclosed to third parties, in whole or in part, without the
express, prior, written permission of Airspan Networks Ltd. In addition, any use of this document or the information contained
herein for the purposes other than those for which it is disclosed is strictly forbidden.
Airspan Networks Inc. reserves the right, without prior notice or liability, to make changes in equipment design or specifications.
Information supplied by Airspan Networks Ltd. is believed in good faith to be accurate and reliable, while every care has been
taken in preparing these documents. However, Airspan Networks Ltd. does not make any representations and gives no
warranties of whatever nature in respect of these documents, including without limitation, the accuracy or completeness of any
information, facts and/or opinions contained therein. No responsibility is assumed by Airspan Networks Ltd. for the use of the
documents nor for the rights of third parties which may be effected in any way by the use thereof. The provision of these
documents (and the documents themselves) does not constitute professional advice of any kind. Any representation(s) in these
documents concerning performance of Airspan Networks Ltd. product(s) are for informational purposes only and are not
warranties of future performance, either expressed or implied. Airspan Networks Ltd., its affiliates, directors, employees and
agents shall not be held liable for any damages or losses, of any nature whatsoever, arising from any use of and/or reliance on
the documents.
These documents may contain flaws, omissions or typesetting errors; no warranty is granted nor liability assumed in relation
thereto unless specifically undertaken in Airspan Networks Ltd. sales contract or order confirmation. Information contained
herein is periodically updated and changes will be incorporated into subsequent editions. If you have encountered an error,
please notify Airspan Networks Ltd.
Product performance figures quoted within this document are indicative and for information purposes only.

DUG01593 Airspan Commercial and Internal Use i
Table of Contents
Document Information.............................................................................1
Document Approvals..............................................................................................1
Revision History.....................................................................................................1
Warnings and Cautions...........................................................................2
Human Exposure to Radio Frequencies ................................................................2
Avertissement et Precautions d’Utilisation ..............................................2
Radio Interference .................................................................................................2
Modifications..........................................................................................................2
General..................................................................................................................2
Général..................................................................................................................3
Important Safety Instructions............................................................................3
Safety.....................................................................................................................3
Securite..................................................................................................................4
Warning of Hazardous Voltages ............................................................................4
Attention aux Voltages Hasardeux.........................................................................5
Adherence to European Directive 2014/53/EU ......................................................5
Warning Symbols...................................................................................................5
Service Information................................................................................................5
UL Information .......................................................................................................6
Lightning Protection ...............................................................................................6
Outdoor Cabling.....................................................................................................7
DECLARATION OF CONFORMITY.......................................................................7
GPS Compliance ...................................................................................................9
Maximum Output TX Total Power.........................................................10
Power Consumption.............................................................................................10
Product Variants ..................................................................................................10
Antenna System...................................................................................................11
About This Document ...........................................................................12
Purpose................................................................................................................12

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use ii
Intended Audience...............................................................................................12
Related Reading ..................................................................................................12
Customer Care Help Desk....................................................................13
Airspan Encourages Comments ..........................................................................13
1Introduction.......................................................................................14
1.1 AirSpeed 1050 B3.........................................................................................14
1.1.1 Deployment..................................................................................................14
2Verifying Prerequisites ......................................................................16
2.1 Verify the Tools .............................................................................................16
2.2 Verify the Parts and Kits................................................................................16
3Physical Description..........................................................................18
3.1 AirSpeed 1050 B3 Physical Dimensions.......................................................18
3.2 Bottom View..................................................................................................19
3.3 Power…........................................................................................................19
3.3.1 Environmental..............................................................................................19
3.4 LEDs Display.................................................................................................20
4Installation of AirSpeed 1050 B3.......................................................21
4.1 Mounting Adaptor Assembly .........................................................................22
4.2 Mounting .......................................................................................................22
4.2.1 Securing the Unit to the Pole Mounting Arm.................................................22
Connect and Manage Cables................................................................24
4.3 Connecting the Ground Cable.......................................................................24
4.4 TX Power Monitoring Port.............................................................................24
4.5 Cable Connection..........................................................................................24
4.5.1 AC Cable Preparation ..................................................................................25
4.5.2 Fiber Ethernet (SFP) Cable Preparation.......................................................30
4.5.3 Copper Ethernet Cable Preparation .............................................................34
5Removal of AirSpeed 1050 B3..........................................................38
5.1 Tool Requirements........................................................................................38
5.2 AC Cable Disconnection ...............................................................................38
5.3 Fiber Ethernet (SFP) Cable Disconnection ...................................................38

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use iii
5.4 Copper Ethernet (RJ45) Cable Disconnection ..............................................38
5.5 Ground Cable Disconnection ........................................................................38
5.6 AirSpeed Removal from the Pole Mounting Arm...........................................39
AJob Sheet..........................................................................................40
BAbbreviations ....................................................................................41
Figures
Figure 1: AirSpeed 1050 B3..................................................................................................................11
Figure 2: AirSpeed 1050 B3..................................................................................................................15
Figure 3: AirSpeed 1050 B3 Overall Dimensions .................................................................................18
Figure 4: AirSpeed 1050 B3 Bottom .....................................................................................................19
Figure 5: Positioning Overview .............................................................................................................21
Figure 6: Mounting Adaptor Assembly..................................................................................................22
Figure 7: Securing on Mounting Bracket...............................................................................................23
Figure 8: AirSpeed 1050 B3 on Pole Mounting Arm (example)............................................................23
Figure 9: Ground Connection................................................................................................................24
Figure 10: Stripping Dimensions (AC Cable)........................................................................................25
Figure 11: Open Housing Lock .............................................................................................................25
Figure 12: Seperate into Sections.........................................................................................................26
Figure 13: Insert Gland Nut...................................................................................................................26
Figure 14: Pass Cable Through............................................................................................................26
Figure 15: Insert Wire to Housing .........................................................................................................27
Figure 16: AC Wire Placement .............................................................................................................27
Figure 17: Tighten Three (3) Set Screws..............................................................................................27
Figure 18: Cable Click in Place.............................................................................................................28
Figure 19: Place Split Rubber Gland ....................................................................................................28
Figure 20: Gland Size on Edge.............................................................................................................28
Figure 21: Place Tightening Cone on Split Gland.................................................................................29
Figure 22: Tighten Gland Nut................................................................................................................29
Figure 23: Close the Lever....................................................................................................................29
Figure 24: Secure Lock.........................................................................................................................29
Figure 25: AC Housing Lock Secured...................................................................................................30
Figure 26: Stripping Dimensions (SFP Cable)......................................................................................30
Figure 27: Pre-assembled LC Duplex Cable ........................................................................................30
Figure 28: Open Housing Lock .............................................................................................................31
Figure 29: Gland Nut on Cable .............................................................................................................31

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use iv
Figure 30: Insert Tightening Cone on Cable.........................................................................................31
Figure 31: Insert Rubber Gland on Cable.............................................................................................31
Figure 32: Pass Cable thru Housing.....................................................................................................32
Figure 33: Insert Cable into Transceiver...............................................................................................32
Figure 34: Insert Holder over theTransceiver .......................................................................................32
Figure 35: Holder into Housing Base....................................................................................................32
Figure 36: Holder into Transceiver........................................................................................................33
Figure 37: Lift Lever ..............................................................................................................................33
Figure 38: Insert Gland .........................................................................................................................33
Figure 39: Insert Cone ..........................................................................................................................33
Figure 40: Tighten Gland Nut................................................................................................................34
Figure 41: Secure Housing Lock...........................................................................................................34
Figure 42: Pre-assembled RJ45 Cable.................................................................................................34
Figure 43: Gland Nut on Cable .............................................................................................................34
Figure 44: Insert Tightening Cone on Cable.........................................................................................35
Figure 45: Insert Rubber Gland on Cable.............................................................................................35
Figure 46: Insert Housing onto Cable ...................................................................................................35
Figure 47: Insert Holder onto RJ45.......................................................................................................35
Figure 48: Holder into Housing Base....................................................................................................36
Figure 49: Align RJ45 into Holder.........................................................................................................36
Figure 50: Lift Lever ..............................................................................................................................36
Figure 51: Insert Gland .........................................................................................................................36
Figure 52: Tighten Gland Nut................................................................................................................37
Figure 53: Secure Housing Lock...........................................................................................................37
Figure 54: Removal from the Mounting Arm.........................................................................................39
Tables
Table 1: AirSpeed 1050 B3 FCC Maximum Output Total Power..........................................................10
Table 2: Power Consumption................................................................................................................10
Table 3: Variants...................................................................................................................................10
Table 4. Tool Requirements - Mounting................................................................................................16
Table 5: AirSpeed 1050 B3 Components .............................................................................................16
Table 6. AirSpeed 1050 B3 Physical Dimensions ................................................................................18
Table 7. AirSpeed 1050 B3 Material & Color........................................................................................18
Table 8. AirSpeed 1050 B3 Environment Compliance .........................................................................20
Table 9: LED Display ............................................................................................................................20
Table 10: Outdoor Power Cable Requirements....................................................................................24
Table 11: Wire Pinout............................................................................................................................27
Table 12: Recommended Gland Sizes.................................................................................................28

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use v
Table 13. Tool Requirements - Removal..............................................................................................38

AirSpeed 1050 B3 Installation guide
DUG01593 Airspan Commercial and Internal Use 1
Document Information
This document details procedures for installing the Airspan’s AirSpeed 1050 B3 Pico-class LTE
eNodeB variant.
Document Approvals
Department
Name
Role
Approval date
Product Management
YSH
Product Line Manager
R&D
EPI
Digital HW Group Manager
Revision History
Document owner: Yoav Shilo, PLM
Revision
Date
Summary of Changes
Created by
0.1 + 0.2
June 2019
Initial document & comments
MSF
0.3
July 2019
Modified from comments
MSF
A
August 2019
Publish
MSF
A1
August 2019
Added to recommended gland sizes
MSF
A2
September 2019
Added LED table, AC pinout & updated bracket
MSF
A3
December 2019
Added Removal instructions
MSF
A4
December 2020-
Updates
YSL

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 2
Warnings and Cautions
Human Exposure to Radio Frequencies
The AirSpeed 1050 B3 when operational should be operated from a minimum safe distance of 2.09ft
(64cm).
Avertissement et Precautions d’Utilisation
Exposition des personnes aux fréquences radioélectriques
Les antennes d’AirSpeed 1050 B3 quand opérationnel doivent être installée et utilisée de façon à
garantir la distance minimale de sécurité de 2.09ft. (64cm).
Radio Interference
This AirSpeed 1050 B3 generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment on and off, the technician is encouraged to try to correct the interference by
performing one or more of the following measures:
Re-orientate or relocate the unit
Increase separation between the units and/or End Device
Connect the equipment to a circuit different from that to which the power source is connected
Modifications
Any changes and modifications to this device that are not expressly approved by Airspan Networks
may void the user's authority to operate the equipment.
General
Only qualified personnel should be allowed to install, replace, and service the equipment.
The device cannot be sold retail, to the general public or by mail order. It must be sold to
operators.
Installation must be controlled.
Installation must be performed by licensed professionals.
Installation requires special training. The AirSpeed 1050 B3 radio and antenna should be
installed ONLY by experienced installation professionals who are familiar with local building
and safety codes and, wherever applicable, are licensed by the appropriate government
regulatory authorities. Failure to do so may void Airspan's product warranty and may expose
the end user or the service provider to legal and financial liabilities. Airspan and its resellers
or distributors are not liable for injury, damage or violation of regulations associated with the
installation of outdoor units or antennas.
The device is to be installed in a Restricted Access Location.

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 3
Général
Seul le personnel qualifié peut être autorisé pour installer ou remplacer l’équipement ainsi
qu’effectuer les opérations de maintenance pour cet équipement.
L’équipement ne peut pas être vendu en grande distribution ou par commande via email à
destination du public. Il doit être vendu aux opérateurs de télécommunications.
Son installation doit être contrôlée
Son Installation doit être effectuée par des professionnels autorises.
Son installation requiert une formation spécifique du personnel. L’AirSpeed 1050 B3, radio et
antenne doit être installe UNIQUEMENT par des installateurs professionnels expérimentés et
ayant une connaissance des constructions locales et règles de sécurité, ainsi que, dès que
nécessaire, disposant d’un agreement des autorités gouvernementales de régulation. Toute
enfreinte a ces obligations peut annuler la garantie délivrée par Airspan pour ces produits et
peut exposer l’utilisateur final ou le fournisseur de services a des dommages légaux et
financiers.
Airspan et ses revendeurs ou ses distributeurs ne sont pas responsables des blessures,
dommages ou violations de la régulation en vigueur lies a l’installation du système extérieur
ou des antennes.
L’Equipment doit être installe dans une zone a accès réduit et contrôle.
Important Safety Instructions
Read and Save these instructions
This Installation Guide contains instructions and warnings that should be followed during
installation, and operation.
Failure to follow these instructions could cause bodily injury and/or product failure.
Safety
1. Read this guide and follow all operating and safety instructions.
2. Supply cord is not shipped with the unit and is to be provided by user. Installation is to be
performed by a qualified electrician according to local codes. Installation to be done in
accordance with the National Electrical Code (NEC), ANSI/NFPA 70, the Canadian
Electrical Code (CEC), Part I, CAN/CSA C22.1, and when applicable, the National
Electrical Safety Code, IEEE C2.
3. Static sensitive components inside - do not remove the lid or base: No user serviceable
parts inside.
4. The ground connection should be made before connecting to supply connections.
5. Position the power cord to avoid possible damage; do not overload circuits.
6. Do not place this product on or near a direct heat source, and avoid placing objects on
the terminal.
7. To avoid electrical shock do not install this device during adverse conditions such as rain
or inclement weather.
8. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the
power before cleaning.
9. The units should not be located too near power lines or other electrical power circuits,
where it can come into contact with such power lines or circuits.
10. The unit must be properly grounded to protect against power surges and accumulated
static electricity. It is the user’s responsibility to install this device in accordance with the
local electrical codes.
11. Installation of the unit must be contracted to a professional installer.

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 4
12. The circuit breaker should be easily accessible in case you have to disconnect the
device.
13. When installed in the final configuration, the product must comply with the applicable
Safety Standards and regulatory requirements of the country in which it is installed. If
necessary, consult with the appropriate regulatory agencies and inspection authorities to
ensure compliance.
Securite
1. Lire attentivement ce guide et suivre les instructions d’utilisation et de sécurité.
2. Le cordon d’alimentation n’est pas livré avec l'appareil et doit être fourni par l'utilisateur.
L’installation doit être effectuée par un électricien qualifié conformément aux règles et
standards locaux. L’installation doit être effectuée en conformité avec le Code national de
l'électricité ( NEC ), ANSI / NFPA 70, le Code canadien de l'électricité (CCE ), Partie I,
CAN / CSA C22.1, et le cas échéant, le Code national de sécurité électrique, IEEE C2.
3. Des composants sensibles a électricité statique sont utilisés à l’intérieur. Ne pas retirer le
coffre ou la base. Aucune pièce a l’intérieur est d’utilité pour l’utilisateur.
4. La connexion "terre" doit être effectuée en priorité et avant d'effectuer les connexions à la
source d'alimentation (phase et neutre).
5. Positionner le cordon d’alimentation de façon à éviter des dommages potentiels. Ne pas
surcharger les circuits.
6. Ne pas placer ce produit sur ou à proximité d’une source directe de chaleur et éviter de
placer des objets sur le terminal.
7. Afin d’éviter des problèmes électriques, ne pas installer cet équipement au cours
d’évènements climatiques difficiles comme averses ou météo non clémente.
8. Utiliser uniquement chiffon de coton pour nettoyage. Ne pas utiliser de produits liquides
ou d’aérosols. Déconnecter le produit de la source d’alimentation avant nettoyage.
9. L’unité ne doit pas être située trop près de lignes électriques ou autres circuits de
puissance, avec lesquels il pourrait entrer en contact.
10. L’émetteur radio doit être correctement relie a la terre afin de le protéger contre les
surtensions ou accumulation d’électricité statique. L’utilisateur est tenu responsable de
l’installation du produit conformément aux règles électrique en vigueur localement.
11. L’installation de unité doit être contractualisée avec un installateur professionnel.
12. L’interrupteur de circuit électrique doit être facilement accessible afin de pouvoir
déconnecter l’équipement.
13. Lors de l’installation de la configuration finale, le produit doit être conforme aux Standards
de Sécurité en vigueur ainsi qu’aux exigences réglementaires du pays dans lequel il est
installé. Si nécessaire, consulter les agences règlementaires appropriées, ainsi que les
autorités chargées de l’inspection afin de garantir la conformité.
Warning of Hazardous Voltages
On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power.
Remove metal jewellery that could come into contact with AC power.
On DC sections, short-circuiting the low voltage, low impedance circuits can cause severe arcing that
may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits.
Note: Airspan products do not contain hazardous substances (as defined in UK Control of
Substances Hazardous to Health Regulations 1989 and the Dangerous Substances Regulations
1990). At the end of any Airspan products life cycle, the customer should consult with Airspan to
ensure that the product is disposed of in conformance with the relevant regulatory requirements.

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 5
Attention aux Voltages Hasardeux
Sur les installations de réseau électrique de type courant alternatif (CA) , des voltages hasardeux
peuvent survenir. Garder une Attention particulière lors d’une vérification ou de travaux sur réseau
électrique CA. Retirer tous bijoux en métal qui pourraient entrer en contact avec l’alimentation ou le
réseau CA.
Sur les portions de réseau électrique de type courant continu (CC), un circuit basse impédance peut
causer de sérieux arcs électriques qui pourraient bruler ou endommager les yeux. Retirer bagues,
anneaux, montres etc… afin d’éviter les court-circuit sur le réseau CC.
Adherence to European Directive 2014/53/EU
European Council Recommendation 2014/53/EU details basic restrictions and reference levels on
human exposure to electromagnetic fields as advised by the ICNIRP. Adherence to these
recommended restrictions and reference levels should provide a high level of protection as regards the
established health effects that may result from exposure to electromagnetic fields.
Airspan equipment is compliant with CE and R&TTE regulations and can be operated in all EU
(European Union) locations listed below:
Country Code
BE
EL
LT
PT
BG
ES
LU
RO
CZ
FR
HU
SI
DK
HR
MT
SK
DE
IT
NL
FI
EE
CY
AT
SE
IE
LV
PL
UK
Warning Symbols
The following symbols may be encountered during installation or troubleshooting. These warning
symbols mean danger. Bodily injury may result if you are not aware of the safety hazards involved in
working with electrical equipment and radio transmitters. Familiarize yourself with standard safety
practices before continuing.
Caution, hot
surface
Caution
Electro-Magnetic
Radiation
High Voltage (AC)
DC
Service Information
Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void
the warranty.
Disconnect the power to this product and return it for service if the following conditions apply:
a. The terminal does not function after following the operating instructions outlined in this
manual.

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 6
b. The product has been dropped or the housing is damaged.
Locate the serial number of the terminal and record this on your registration card for future reference.
Also record the MAC address, located on the product sticker.
UL Information
- The equipment must be properly grounded according with NEC and other local safety code
requirements.
- Reminder to system installers: Attention to Section 820-40 of the NEC which provides guidelines for
proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as is practical.
- AirSpeed 1050 B3 is designed to operate in environmental conditions complying with IP66 and
relevant standards.
Lightning Protection
WARNING: The following notes are general recommendations for the system. The wireless equipment
should be installed by a qualified professional installer and must follow local and national codes for
electrical grounding and safety. Failure to meet safety requirements and/or use of non-standard
practices and procedures could result in personal injury and damage to equipment. A direct lightning
strike may cause serious damage even if these guidelines are followed.
All outdoor wireless equipment is susceptible to lightning damage from a direct hit or induced current
from a near strike. Lightning protection and grounding practices in local and national electrical codes
serve to minimize equipment damage, service outages, and serious injury. The antennas are to be DC
grounded, so surge protection may not be required. Reasons for lightning damage are summarized as:
- Poorly grounded tower/antenna sites that can conduct high lightning strike energy into equipment.
- Lack of properly installed lightning protection equipment that can cause equipment failures from
lightning induced currents.
A lighting protection system provides a means by which the energy may enter earth without passing
through and damaging parts of a structure. A lightning protection system does not prevent lightning
from striking; it provides a means for controlling it and preventing damage by providing a low resistance
path for the discharge of energy to travel safely to ground. Improperly grounded connections are also a
source of noise that can cause sensitive equipment to malfunction.
A good tower grounding system disperses most of the surge energy from a tower strike away from the
building and equipment.
To limit the equipment damage due to a lightning strike, the following practices are recommended for
the wireless system:
- Provide direct grounding from the antenna mounting bracket, the radio and antenna and the
lightning/surge protectors to the same ground point at the base of the tower or a ground bus on the
building. Use the grounding screws on the antenna bracket and the radio and antenna for terminating
the ground wires.
- The circuit ground must be connected to the same grounding system as the unit.

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 7
Outdoor Cabling
- Connected cables should be outdoor grade with UV protection.
- Use shielded out CAT6 cabled terminated with metallic RJ45 connectors.
- Surge protection circuit must use a minimum 14AWG grounding cable.
DECLARATION OF CONFORMITY
Declaration of Conformity with Regard to the R&TTE Directive 2014/53/EU
Czech:
Airspan tímto prohlašuje, že tento přístroj je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 2014/53 / EU.
Danish:
Undertegnede, Airspan erklærer hermed, at følgende udstyrsenhed opfylder de væsentlige krav og
andre relevante krav i direktiv 2014/53 / EF.
Deutsch:
Hiermit erklärt Airspan, dass die Produkteinheit die grundlegenden Anforderungen und anderen
relevanten Bestimmungen der Richtlinie 2014/53 / EU erfüllt.
Estonian:
Käesolevaga kinnitab Airspan, et seadme seade vastab direktiivi 2014/53 / EL olulistele nõuetele ja
muudele kõnealuse direktiivi asjakohastele sätetele.
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU.
Español:
Por medio de este Airspan, declara que la unidad cumple con los requisitos esenciales y cualquier otra
disposición aplicable o exigible de la Directiva 2014/53 / UE.
Greek:
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ΠΡΟΔΙΑΓΡΑΦΗ, η Airspan ΔΗΛΩΝΕΤΑΙ ότι η μονάδα συμμορφώνεται με τις
ουσιώδεις απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 2014/53 / ΕE.
Français:
Airspan déclare par la présente que l'appareil est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 2014/53 / UE.
Italiano:
Con la presente Airspan dichiara che questa unità è conforme ai requisiti essenziali e alle altre
disposizioni pertinenti stabilite dalla direttiva 2014/53 / UE.
Latvian:
Ar šo Airspan paziņo, ka vienība atbilst Direktīvas 2014/53 / ES būtiskajām prasībām un citiem
attiecīgajiem noteikumiem;
Lithuanian:
Šis „Airspan“ pareiškia, kad šis įrenginys atitinka esminius Direktyvos 2014/53 / ES reikalavimus ir kitas
nuostatas.
Nederlands:
Airspan verklaart hierbij dat de apparaateenheid voldoet aan de essentiële vereisten en andere
relevante bepalingen van richtlijn 2014/53 / EU.

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 8
Maltese:
Hawnhekk, Airspan, tiddikjara li din l-unità tikkonforma mar-rekwiżiti essenzjali u dispożizzjonijiet
rilevanti oħra li jinsabu fid-Direttiva 2014/53 / UE.
Hungarian:
Alulírott, az Airspan kijelenti, hogy az egység megfelel a 2014/53 / EU irányelv vonatkozó alapvető
követelményeinek és egyéb követelményeinek.
Polish:
Niniejszym Airspan oświadcza, że urządzenie jest zgodne z zasadniczymi wymaganiami i innymi
odpowiednimi postanowieniami dyrektywy 2014/53 / UE.
Português:
Airspan declara que esta unidade está em conformidade com os requisitos essenciais e outras
disposições da Diretiva 2014/53 / UE.
Slovenian:
Airspan izjavlja, da je ta enota skladna z bistvenimi zahtevami in drugimi ustreznimi določbami Direktive
2014/53 / EU.
Slovak:
Airspan týmto vyhlasuje, že tento prístroj spĺňa základné požiadavky a všetky príslušné ustanovenia
Smernice 2014/53 / EÚ.
Suomalainen:
Airspan vakuuttaa täten, että laitteen tyyppi on direktiivin 2014/53 / EU olennaisten vaatimusten ja
muiden asiaankuuluvien säännösten mukainen.
Swedish:
Därmed intygar Airspan att denna enhet överensstämmer med de väsentliga egenskapskraven och
andra relevanta bestämmelser som anges i direktiv 2014/53 / EU.
Íslenska:
Airspan lýsir hér með yfir að þessi eining uppfylli grunnkröfur og aðrar kröfur tilskipunar 2014/53 / ESB.
Norsk:
Airspan erklærer herved at utstyrsenheten oppfyller grunnleggende krav og andre relevante krav i
direktiv 2014/53 / EU.
Român:
Airspan declarăm pe propria răspundere că produsul produsului respectă cerințele esențiale și alte
prevederi aplicabile din Directiva 2014/53 / UE.
The Declaration of Conformity related to this product can be obtained from [email protected].

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 9
GPS Compliance
The GPS is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC."
The GPS complies with the following EMC Common Regulatory Testing standards:
EN55022: Radiated and Conducted Emissions
CISPR 22: Class B
EN 50081-1: Generic Emissions Class B
EN 50082-1: Generic Immunity Class B
EN 61000-4-2: Electrostatic Discharge Immunity
EN 61000-4-3: Radiated RF EM Field Immunity Test
EN 61000-4-4: Electrical Fast Transient/Burst Test
EN 61000-4-6: Conducted Immunity
EN 61000-4-8: Magnetic Field Immunity
Note: A GPS is recommended for synchronizing the unit (included in the system).
Note: An optional GPS Lightning/Surge protector is available from Airspan when installing the GPS
antenna in a remote location for lightning prone deployments.

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 10
Maximum Output TX Total Power
Table 1: AirSpeed 1050 B3 FCC Maximum Output Total Power
Frequency Band
(MHz)
TX (dBm)
(per sector)
EIRP (dBm)
(per sector)
Antenna Gain (dBi)
Variant
1825 - 1845
2x32
46
11
1050
Caution: Do not set maximum output TX power to higher than local regulations.
Power Consumption
AirSpeed 1050 B3 power consumption is described in the following table:
Table 2: Power Consumption
Duplex
Tx Power at RF Port
(dBm)
Nominal Power Consumption
(W)
Max Power Consumption
(W)
FDD
4x 32
60
90
FDD
4x 34
75
105
Product Variants
Table 3: Variants
Product Name
Product Code
Description
AirSpeed 1050 B3-M1
Fiber BH, AC power
AS105-U03M1-B08A
AirSpeed 1050, 1825 - 1845 MHz (B3-M1),
Fiber Backhaul, AC

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 11
Antenna System
The AirSpeed 1050 B3 includes embedded antennas: 2x SBA. Each SBA includes two antenna
elements which can be switch on/off.
Figure 1: AirSpeed 1050 B3

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 12
About This Document
Purpose
This guide provides the workflow and step-by-step procedures for Installing the AirSpeed 1050 B3.
These procedures include:
Verify prerequisites
Install the AirSpeed 1050 B3
Connect and manage cables
Intended Audience
This guide is intended for persons who are responsible for installing the AirSpeed 1050 B3 equipment.
These persons should have a working knowledge of the equipment.
Related Reading
The following documents contain related information:
AirSpeed 1050 B3 Product Datasheet
Airspan LTE Commissioning Manual

AirSpeed 1050 B3 Installation Guide
DUG01593 Airspan Commercial and Internal Use 13
Customer Care Help Desk
Airspan’s Customer Care Help Desk offers prompt and efficient customer support services.
Note: To avail Airspan’s Customer Care Help Desk support, you must be a registered user and must
have a valid support contract. To register, click here and fill the Registration form.
To create and update issue logs, send e-mails to Customer Care Help Desk. Once you submit your
issue, the system generates a new issue and sends an issue number for your reference. The system
uses this issue number to categorize and store e-mails under the appropriate issue.
To help Customer Care Help Desk identify your issue, include the issue number and your Customer
Care Helpdesk account details in all further communications.
Main Operations
Airspan Communications Ltd.
Capital Point
33 Bath Road
Slough, Berkshire
SL1 3UF, United Kingdom
Tel: [phone]
Worldwide Headquarters
Airspan Networks Inc.
777, Yamato Road, Suite 105
Boca Raton, FL 3341-4408, USA
Tel: [phone]
Airspan Encourages Comments
Airspan welcomes any feedback and suggestions that help to improve the quality of the documentation.
Send your feedback to docum[email protected]om.