Airspan AirSpeed 1000A User manual

AirSpeed 1000A Installation Guide
Part Number: DUG01289
Revision: A12
Published: May 2023

© Copyright by Airspan Networks Ltd., 2023. All rights reserved worldwide.
Legal Notices
The information contained within this document is proprietary, privileged and intended only for the recipient. As
such, the information is subject to all relevant copyright, patent and other laws protecting intellectual property, as
well as any specific agreements protecting Airspan Networks Ltd. rights in the aforesaid information. Neither this
document nor the information contained herein may be published, reproduced, transmitted or disclosed to third
parties, in whole or in part, without the express, prior, written permission of Airspan Networks Ltd. In addition, any
use of this document or the information contained herein for the purposes other than those for which it is disclosed
is strictly forbidden.
Airspan Networks Ltd. reserves the right, without prior notice or liability, to make changes in equipment design or
specifications.
Information supplied by Airspan Networks Ltd. is believed in good faith to be accurate and reliable, while every
care has been taken in preparing these documents. However, Airspan Networks Ltd. does not make any
representations and gives no warranties of whatever nature in respect of these documents, including without
limitation, the accuracy or completeness of any information, facts and/or opinions contained therein. No
responsibility is assumed by Airspan Networks Ltd. for the use of the documents nor for the rights of third parties
which may be effected in any way by the use thereof. The provision of these documents (and the documents
themselves) does not constitute professional advice of any kind. Any representation(s) in these documents
concerning performance of Airspan Networks Ltd. product(s) are for informational purposes only and are not
warranties of future performance, either expressed or implied. Airspan Networks Ltd., its affiliates, directors,
employees and agents shall not be held liable for any damages or losses, of any nature whatsoever, arising from
any use of and/or reliance on the documents.
These documents may contain flaws, omissions or typesetting errors; no warranty is granted nor liability assumed
in relation thereto unless specifically undertaken in Airspan Networks Ltd. sales contract or order confirmation.
Information contained herein is periodically updated and changes will be incorporated into subsequent editions. If
you have encountered an error, please notify Airspan Networks Ltd.
Product performance figures quoted within this document are indicative and for information purposes only.
Acknowledgements
© Intel Corporation http://www.intel.com/
© Microsoft Corporation http://www.microsoft.com

DUG01289 Airspan Commercial and Internal Use i
Table of Contents
Document Information..............................................................................2
Abstract.................................................................................................................. 2
Revision History ..................................................................................................... 2
Warnings and Cautions............................................................................3
Human Exposure to Radio Frequencies ................................................................ 3
Avertissement et Precautions d’Utilisation...............................................3
Exposition des personnes aux fréquences radioélectriques .................................. 3
Radio Interference ................................................................................................. 3
Modifications .......................................................................................................... 3
General .................................................................................................................. 3
Général .................................................................................................................. 3
Important Safety Instructions............................................................................ 4
Safety..................................................................................................................... 4
Securite.................................................................................................................. 4
Warning of Hazardous Voltages ............................................................................ 5
Attention aux Voltages Hasardeux......................................................................... 5
Adherence to European Directive 2014/53/EU ...................................................... 5
Warning Symbols................................................................................................... 5
Service Information ................................................................................................ 5
UL Information ....................................................................................................... 6
DECLARATION OF CONFORMITY ........................................................6
Maximum Output TX Power.....................................................................8
Product Variants .................................................................................................... 8
Power Consumption............................................................................................... 8
External Antennas.................................................................................................. 9
About This Document.............................................................................10
Purpose................................................................................................................ 10
Intended Audience ............................................................................................... 10
Document Conventions........................................................................................ 10

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use ii
Related Reading .................................................................................................. 11
Customer Care Help Desk .....................................................................12
Airspan Encourages Comments .......................................................................... 12
1Introduction.........................................................................................13
1.1 AirSpeed 1000A ............................................................................................ 13
2Getting Started ...................................................................................14
2.1 Workflow of Installation ................................................................................. 14
2.2 AirSpeed 1000A Installation Checklist........................................................... 14
3Verifying Prerequisites .......................................................................15
3.1 Verifying Site Requirements.......................................................................... 15
3.2 Verify Installation Requirements.................................................................... 15
3.2.1 Verify the Tools.............................................................................................. 15
3.2.2 Verify the Parts and Kits ................................................................................ 16
3.2.3 Power Supply................................................................................................. 17
3.2.4 Connections................................................................................................... 17
3.2.5 Physical Dimensions...................................................................................... 18
3.2.6 Environmental................................................................................................ 18
4AirSpeed 1000A Installation ...............................................................20
4.1 Connecting the GPS Antenna ....................................................................... 20
4.2 Pole Mounting Assembly............................................................................... 21
4.2.1 Pole Mounting (Larger Poles) ........................................................................ 21
4.3 Wall Mount Assembly.................................................................................... 23
4.4 LED Display .................................................................................................. 24
5Connect and Manage Cables.............................................................25
5.1 Grounding ..................................................................................................... 25
5.2 Remote Antenna Assembly........................................................................... 25
5.3 Weather-proofing Antenna Connections ....................................................... 25
5.4 Ethernet Cable Installation ............................................................................ 26
5.5 Connecting the DC Power Cable .................................................................. 26
AJob Sheet ...........................................................................................28
BChecklist.............................................................................................29

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use iii
CAbbreviations......................................................................................30
Figures
Figure 1: AirSpeed 1000A.......................................................................................................................9
Figure 2: AirSpeed 1000A Front View ..................................................................................................13
Figure 3: Workflow ................................................................................................................................14
Figure 4: AirSpeed 1000A Top Ports ....................................................................................................17
Figure 5: AirSpeed 1000A Bottom Ports...............................................................................................18
Figure 6: Attaching GPS Antenna.........................................................................................................20
Figure 7: Pole Mounting Assembly .......................................................................................................22
Figure 8: Mounted on Pole....................................................................................................................22
Figure 9: AirSpeed on Wall...................................................................................................................23
Figure 10: Connecting Antenna RF Cable............................................................................................25
Figure 11: Weather-proof the Connection.............................................................................................25
Figure 12: Gland Connected.................................................................................................................26
Figure 13: Ethernet Cable through Connector......................................................................................26
Figure 14: Power Cable Attached .........................................................................................................27
Tables
Table 1: AirSpeed 1000A ETSI Maximum Output TX Power .................................................................8
Table 2: AirSpeed 1000A FCC Maximum Output TX Power..................................................................8
Table 3: Supported Frequency Bands ....................................................................................................8
Table 4: Power Consumption..................................................................................................................8
Table 5: Typographic Conventions .......................................................................................................10
Table 6. Minimum Hardware Requirements .........................................................................................15
Table 7. Parts & Kits .............................................................................................................................16
Table 8. AirSpeed 1000A Physical Dimensions....................................................................................18
Table 9. AirSpeed 1000A Environment Compliance ............................................................................19
Table 10. AirSpeed 1000A LED Behavior “During Startup”..................................................................24
Table 11. Wiring Table..........................................................................................................................26
Table 12: ABBREVIATIONS & DEFINITIONS......................................................................................30

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 2
Document Information
Abstract
This document details procedures for installing the Airspan’s AirSpeed 1000A Pico-class LTE eNodeB
variant.
Revision History
Revision Details Date Summary of Changes
Rev 0.1 – 0.2
August 2017
•Initial document – draft(s)
•
comments
Rev A
August 2017
•comments
•Published
Rev A1
January 2019
•Updates
Rev A2
February 2019
•Corrections
•Updates
Rev A3
March 2019
•Update EU Directive
Rev A4
March 2019
•Added power cable
Rev A5
March 2019
•Relabeled antenna ports
Rev A6
June 2019
•Update product antenna port pictures
Rev A7
December 2019
•Update power cable data
Rev A8
May 2020
•Added LED display table
Rev A9
September 2020
•
EiRP update
Rev A10
January 2021
•WEEE reference - removal
Rev A11
April 2023
•Safety distance update
•Antenna Gain correction
Rev A12
May 2023
•Product name change

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 3
Warnings and Cautions
Human Exposure to Radio Frequencies
To comply with FCC RF exposure compliance requirements, the device should be located at a distance
of at least 20 cm (7.87 in.) from all persons during normal operation. The antennas used for this product
must not be co-located or operated in conjunction with any other antenna or transmitter.
Avertissement et Precautions d’Utilisation
Exposition des personnes aux fréquences radioélectriques
Les AirSpeed 1000A doivent être installée et utilisée de façon à garantir la distance minimale de
sécurité de 20 cm (7.87 in.).
Radio Interference
This AirSpeed 1000A generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio, television reception or WiFi AP, which can be
determined by turning the equipment on and off, the technician is encouraged to try to correct the
interference by performing one or more of the following measures:
Re-orientate or relocate the unit
Increase separation between the units and/or End Devices
Connect the equipment to an outlet on a circuit different from that to which the power source is
connected
Modifications
Any changes and modifications to this device that are not expressly approved by Airspan Networks
may void the user's authority to operate the equipment.
General
Only qualified personnel should be allowed to install, replace, and service the equipment.
The device cannot be sold retail, to the general public or by mail order. It must be sold to
operators.
Installation must be controlled.
Installation must be performed by licensed professionals.
Installation requires special training. The AirSpeed 1000A should be installed ONLY by
experienced installation professionals who are familiar with local building and safety codes
and, wherever applicable, are licensed by the appropriate government regulatory authorities.
Failure to do so may void Airspan's product warranty and may expose the end user or the
service provider to legal and financial liabilities.
Airspan and its resellers or distributors are not liable for injury, damage or violation of
regulations associated with the installation of units or antennas.
Général
Seul le personnel qualifié peut être autorisé pour installer ou remplacer l’équipement ainsi
qu’effectuer les opérations de maintenance pour cet équipement.
L’équipement ne peut pas être vendu en grande distribution ou par commande via email à
destination du public. Il doit être vendu aux opérateurs de télécommunications.
Son installation doit être contrôlée
Son Installation doit être effectuée par des professionnels autorises.

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 4
Son installation requiert une formation spécifique du personnel. L’AirSpeed 1000A, radio et
antenne doit être installe UNIQUEMENT par des installateurs professionnels expérimentés et
ayant une connaissance des constructions locales et règles de sécurité, ainsi que, dès que
nécessaire, disposant d’un agreement des autorités gouvernementales de régulation. Toute
enfreinte a ces obligations peut annuler la garantie délivrée par Airspan pour ces produits et
peut exposer l’utilisateur final ou le fournisseur de services a des dommages légaux et
financiers.
Airspan et ses revendeurs ou ses distributeurs ne sont pas responsables des blessures,
dommages ou violations de la régulation en vigueur lies a l’installation du système ou des
antennes.
Important Safety Instructions
Read and Save these instructions
This Installation Guide contains instructions and warnings that should be followed during
installation, and operation.
Failure to follow these instructions could cause bodily injury and/or product failure
Safety
1. Read this guide and follow all operating and safety instructions.
2. No user serviceable parts inside.
3. Position the power cord to avoid possible damage; do not overload circuits.
4. Do not place this product on or near a direct heat source and avoid placing objects on the
terminal.
5. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect the
power before cleaning.
6. The units should not be located near power lines or other electrical power circuits.
7. It is the user’s responsibility to install this device in accordance with the local electrical
codes.
8. Installation of the AirSpeed 1000A must be contracted to a professional installer.
9. The circuit breaker should be easily accessible in case you have to disconnect the
device.
10. When installed in the final configuration, the product must comply with the applicable
Safety Standards and regulatory requirements of the country in which it is installed. If
necessary, consult with the appropriate regulatory agencies and inspection authorities to
ensure compliance.
Securite
1. Lire attentivement ce guide et suivre les instructions d’utilisation et de sécurité.
2. Aucune pièce a l’intérieur est d’utilité pour l’utilisateur.
3. Positionner le cordon d’alimentation de façon à éviter des dommages potentiels. Ne pas
surcharger les circuits.
4. Ne pas placer ce produit sur ou à proximité d’une source directe de chaleur et éviter de
placer des objets sur le terminal.
5. Utiliser uniquement chiffon de coton pour nettoyage. Ne pas utiliser de produits liquides
ou d’aérosols. Déconnecter le produit de la source d’alimentation avant nettoyage.
6. L’unité ne doit pas être située trop près de lignes électriques ou autres circuits de
puissance, avec lesquels il pourrait entrer en contact.
7. L’utilisateur est tenu responsable de l’installation du produit conformément aux règles
électrique en vigueur localement.

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 5
8. L’installation de AirSpeed 1000A doit être contractualisée avec un installateur
professionnel.
9. L’interrupteur de circuit électrique doit être facilement accessible afin de pouvoir
déconnecter l’équipement.
10. Lors de l’installation de la configuration finale, le produit doit être conforme aux Standards
de Sécurité en vigueur ainsi qu’aux exigences réglementaires du pays dans lequel il est
installé. Si nécessaire, consulter les agences règlementaires appropriées, ainsi que les
autorités chargées de l’inspection afin de garantir la conformité.
Warning of Hazardous Voltages
On AC installations, hazardous voltages exist. Use caution when verifying or working with AC power.
Remove metal jewellery that could come into contact with AC power.
On DC sections, short-circuiting the low voltage, low impedance circuits can cause severe arcing that
may result in burns or eye damage. Remove rings, watches etc. to avoid shorting DC circuits.
Note: Airspan products do not contain hazardous substances (as defined in UK Control of
Substances Hazardous to Health Regulations 1989 and the Dangerous Substances Regulations
1990). At the end of any Airspan products life cycle, the customer should consult with Airspan to
ensure that the product is disposed of in conformance with the relevant regulatory requirements.
Attention aux Voltages Hasardeux
Sur les installations de réseau électrique de type courant alternatif (CA), des voltages hasardeux
peuvent survenir. Garder une Attention particulière lors d’une vérification ou de travaux sur réseau
électrique CA. Retirer tous bijoux en métal qui pourraient entrer en contact avec l’alimentation ou le
réseau CA.
Sur les portions de réseau électrique de type courant continu (CC), un circuit basse impédance peut
causer de sérieux arcs électriques qui pourraient bruler ou endommager les yeux. Retirer bagues,
anneaux, montres etc… afin d’éviter les court-circuit sur le réseau CC.
Adherence to European Directive 2014/53/EU
European Council Recommendation 2014/53/EU details basic restrictions and reference levels on
human exposure to electromagnetic fields as advised by the ICNIRP. Adherence to these
recommended restrictions and reference levels should provide a high level of protection as regards
the established health effects that may result from exposure to electromagnetic fields.
Warning Symbols
The following symbols may be encountered during installation or troubleshooting. These warning
symbols mean danger. Bodily injury may result if you are not aware of the safety hazards involved in
working with electrical equipment and radio transmitters. Familiarize yourself with standard safety
practices before continuing.
Caution, hot surface Caution Electro-Magnetic
Radiation
DC
Service Information
Refer all repairs to qualified service personnel. Do not modify any part of this device, as this will void
the warranty.
Disconnect the power to this product and return it for service if the following conditions apply:
a. The terminal does not function after following the operating instructions outlined in this
manual.

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 6
b. Liquid has been spilled, a foreign object is inside, or the terminal has been exposed to
rain.
c. The product has been dropped or the housing is damaged.
Locate the serial number of the terminal and record this on your registration card for future reference.
Also record the MAC address, located on the product sticker.
UL Information
- The electrical source must be properly grounded according with NEC and other local safety code
requirements.
- AirSpeed 1000A is designed to operate in environmental conditions complying with IP40 and
relevant standards.
DECLARATION OF CONFORMITY
Declaration of Conformity with Regard to the R&TTE Directive 2014/53/EU
Czech:
Airspan tímto prohlašuje, že tento přístroj je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 2014/53 / EU.
Danish:
Undertegnede, Airspan erklærer hermed, at følgende udstyrsenhed opfylder de væsentlige krav og
andre relevante krav i direktiv 2014/53 / EF.
Deutsch:
Hiermit erklärt Airspan, dass die Produkteinheit die grundlegenden Anforderungen und anderen
relevanten Bestimmungen der Richtlinie 2014/53 / EU erfüllt.
Estonian:
Käesolevaga kinnitab Airspan, et seadme seade vastab direktiivi 2014/53 / EL olulistele nõuetele ja
muudele kõnealuse direktiivi asjakohastele sätetele.
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU.
Español:
Por medio de este Airspan, declara que la unidad cumple con los requisitos esenciales y cualquier otra
disposición aplicable o exigible de la Directiva 2014/53 / UE.
Greek:
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ΠΡΟΔΙΑΓΡΑΦΗ, η Airspan ΔΗΛΩΝΕΤΑΙ ότι η μονάδα συμμορφώνεται με τις
ουσιώδεις απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 2014/53 / ΕE.
Français:
Airspan déclare par la présente que l'appareil est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 2014/53 / UE.
Italiano:
Con la presente Airspan dichiara che questa unità è conforme ai requisiti essenziali e alle altre
disposizioni pertinenti stabilite dalla direttiva 2014/53 / UE.
Latvian:
Ar šo Airspan paziņo, ka vienība atbilst Direktīvas 2014/53 / ES būtiskajām prasībām un citiem
attiecīgajiem noteikumiem;
Lithuanian:

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 7
Šis „Airspan“ pareiškia, kad šis įrenginys atitinka esminius Direktyvos 2014/53 / ES reikalavimus ir kitas
nuostatas.
Nederlands:
Airspan verklaart hierbij dat de apparaateenheid voldoet aan de essentiële vereisten en andere
relevante bepalingen van richtlijn 2014/53 / EU.
Maltese:
Hawnhekk, Airspan, tiddikjara li din l-unità tikkonforma mar-rekwiżiti essenzjali u dispożizzjonijiet
rilevanti oħra li jinsabu fid-Direttiva 2014/53 / UE.
Hungarian:
Alulírott, az Airspan kijelenti, hogy az egység megfelel a 2014/53 / EU irányelv vonatkozó alapvető
követelményeinek és egyéb követelményeinek.
Polish:
Niniejszym Airspan oświadcza, że urządzenie jest zgodne z zasadniczymi wymaganiami i innymi
odpowiednimi postanowieniami dyrektywy 2014/53 / UE.
Português:
Airspan declara que esta unidade está em conformidade com os requisitos essenciais e outras
disposições da Diretiva 2014/53 / UE.
Slovenian:
Airspan izjavlja, da je ta enota skladna z bistvenimi zahtevami in drugimi ustreznimi določbami Direktive
2014/53 / EU.
Slovak:
Airspan týmto vyhlasuje, že tento prístroj spĺňa základné požiadavky a všetky príslušné ustanovenia
Smernice 2014/53 / EÚ.
Suomalainen:
Airspan vakuuttaa täten, että laitteen tyyppi on direktiivin 2014/53 / EU olennaisten vaatimusten ja
muiden asiaankuuluvien säännösten mukainen.
Swedish:
Därmed intygar Airspan att denna enhet överensstämmer med de väsentliga egenskapskraven och
andra relevanta bestämmelser som anges i direktiv 2014/53 / EU.
Íslenska:
Airspan lýsir hér með yfir að þessi eining uppfylli grunnkröfur og aðrar kröfur tilskipunar 2014/53 / ESB.
Norsk:
Airspan erklærer herved at utstyrsenheten oppfyller grunnleggende krav og andre relevante krav i
direktiv 2014/53 / EU.
Român:
Airspan declarăm pe propria răspundere că produsul produsului respectă cerințele esențiale și alte
prevederi aplicabile din Directiva 2014/53 / UE.
The Declaration of Conformity related to this product can be obtained from [email protected].

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 8
Maximum Output TX Power
Table 1: AirSpeed 1000A ETSI Maximum Output TX Power
Frequency Band
(MHz)
ETSI
TX (dBm) EIRP (dBm)
Antenna Gain
(dBi)
Variant
3550-3700
25
48
9
1000
Table 2: AirSpeed 1000A FCC Maximum Output TX Power
Frequency Band
(MHz)
FCC
TX (dBm) EIRP (dBm)
Antenna Gain
(dBi)
Variant
3550-3700
23.08
48
9
1000
Note:The AirSpeed 1000A requires operation using an Airspan FCC-specific version of Netspan
acting as a CBRS Domain Proxy.
Caution:Do not set maximum output TX total power to higher than local regulations.
Product Variants
AirSpeed supports the following frequency bands with the specific performance values:
Table 3: Supported Frequency Bands
LTE Band Variant Downlink
Freq.
(MHz)
Uplink
Freq.
(MHz)
Duplex Tx / Rx
Conf.
Tx Power
per Port
(dBm)
Power
Source
48, 42H,
43L AS10-U48-B02D 3550-3700 3550-3700 TDD 2 x 2 25 DC
Power Consumption
Table 4: Power Consumption
Power Source Nominal Power Consumption
(W)
Max Nominal Power
Consumption (W)
DC 40 65
Note:Nominal Power Consumption (W) - refers to average power consumption over time.

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 9
External Antennas
AirSpeed 1000A connects to the external antennas via four (4) N-Type female connectors located at
the top panel. The antenna should be mounted to its appropriate mounting facility.
The supported antennas must be dual slant, cross polar, DC grounded antennas.
Note:For a list of compatible external antennas, please contact your nearest Airspan Sales
representative.
Figure 1: AirSpeed 1000A

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 10
About This Document
Purpose
This guide provides the workflow and step-by-step procedures for installing the Airspan’s AirSpeed
1000A, Pico-class LTE eNodeB variant. These procedures include:
Verify prerequisites
Install Mounting bracket
Install the AirSpeed 1000A
Connect and manage cables
Intended Audience
This guide is intended for persons who are responsible for installing the AirSpeed 1000A equipment.
Document Conventions
This document uses the following typographic conventions.
Table 5: Typographic Conventions
Convention Element
Blue underlined text Cross-reference links.
Bold text Keyboard buttons and GUI elements.
Command Command names or phrases.
Computer output Text displayed by the computer.
Hyperlinks Website and e-mail addresses.
Danger
Signifies a hazardous situation—if not avoided—will
cause death or serious injury. Describes how to avoid
it.
Warning
Signifies a hazardous situation—if not avoided—can
cause death or serious personal injury. Describes
how to avoid it.
Caution
Signifies a hazardous situation—if not avoided—can
void the product warranty, and cause property
damage. Describes how to avoid it.
Important Provides necessary information to explain a task.
Note Provides additional information.
Tip Provides helpful hints.

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 11
Related Reading
The following documents contain related information:
•AirSpeed 1000A Product Datasheet
•Airspan LTE Commissioning Manual

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 12
Customer Care Help Desk
Airspan’s Customer Care Help Desk offers prompt and efficient customer support services.
Note:To avail Airspan’s Customer Care Help Desk support, you must be a registered user and must
have a valid support contract. To register, click here and fill the Registration form.
To create and update issue logs, send e-mails to Customer Care Help Desk. Once you submit your
issue, the system generates a new issue and sends an issue number for your reference. The system
uses this issue number to categorize and store e-mails under the appropriate issue.
To help Customer Care Help Desk identify your issue, include the issue number and your Customer
Care Helpdesk account details in all further communications.
Main Operations
Airspan Communications Ltd.
Capital Point
33 Bath Road
Slough, Berkshire
SL1 3UF, United Kingdom
Tel: [phone]
Worldwide Headquarters
Airspan Networks Inc.
777, Yamato Road, Suite 105
Boca Raton, FL 3341-4408, USA
Tel: [phone]
Airspan Encourages Comments
Airspan welcomes any feedback and suggestions that help to improve the quality of the documentation.
Send your feedback to documentfeedbac[email protected].

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 13
1 Introduction
This section provides a descriptive overview of the Airspan’s AirSpeed 1000A Pico-class eNodeB
variant and its place in the Airspan product suite.
1.1 AirSpeed 1000A
AirSpeed 1000A is part of Airspan’s carrier-class LTE Advanced outdoor small cell eNodeB family.
AirSpeed 1000A is a Pico-class LTE eNodeB product, providing high-speed data, mobility, Voice over
LTE, and broadcast/multicast services.
AirSpeed 1000A is a super compact, easy to install Pico-class eNodeB. Allowing an operator to
deploy LTE broadband services on any Street Furniture, rooftop or building front.
AirSpeed 1000A is a dual sector / carrier 2x2 MIMO product.
Note:For management, please refer to the Airspan LTE Commissioning Manual as well as the
Netspan User Manual.
Note:The AirSpeed 1000A requires operation using an Airspan FCC-specific version of Netspan
acting as a CBRS Domain Proxy.
The AirSpeed 1000A unit is displayed below.
Figure 2: AirSpeed 1000A Front View

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 14
2 Getting Started
2.1 Workflow of Installation
The Workflow to install the AirSpeed 1000A is displayed in the following diagram:
Figure 3: Workflow
2.2 AirSpeed 1000A Installation Checklist
Plan the installation of the AirSpeed 1000A by using the Installation Checklist, which you can find as a
removable job aid in Appendix Bfor this guide.

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 15
3 Verifying Prerequisites
Prior to installing the AirSpeed 1000A, verify the required safety, power, tools, parts and components.
This chapter includes the hardware, software, and client requirements for installation.
Important:Set up requirements for the installation is detailed in the Job Sheet, see Appendix A.
3.1 Verifying Site Requirements
To set up the AirSpeed 1000A, an IP connection to a Netspan server is required.
3.2 Verify Installation Requirements
3.2.1 Verify the Tools
Table 6. Minimum Hardware Requirements
Tool Use
Large flat bladed screwdriver
securing the pole straps (bands)
13 mm wrench
for securing M8 nuts
10 mm or 13/32 inch wrench
for securing M6 nuts
Large pliers
Tightening cable glands - To fit 15 mm
Note:Airspan does not provide screws and wall anchors for mounting the unit to the wall. The screw
size depends on the structure of the building to which the unit is to be attached. When selecting
screw sizes, consideration must be given to the weight of the unit and load that may be induced in
windy conditions.

AirSpeed 1000A Installation Guide
DUG01289 Airspan Commercial and Internal Use 16
3.2.2 Verify the Parts and Kits
Note:Verify order and requirements to ensure the correct unit type is being installed.
Table 7. Parts & Kits
Installation Kit
/ Part
Product
Code Airspan No. Consisting of: Images
AirSpeed 1000A,
3.550-3.700 GHz
(B48)
AS10-U48-
B02D
998-73-483
AirSpeed 1000A Copper
Backhaul, DC Unit
AirSpeed 1000A
Acc. Mounting Kit
TBD
903-03-803
AirSpeed 1000A mounting kit
including:
1 - CPE Pole mount
Bracket Base
2 – U-bolt M8 x2
for 1” (33.7mm) to 1.5”
(48.3mm) pole
4 - M8 Hex Nut
4 – Washer Spring
4 – Washer M8
4 – M6 x 20 Hex head
bolt with 2 washers
2- Maxi Clamps, band
9/16” wide + quick
adjustment lock – for
1.8” (45 mm) to 8”
(210 mm) pole
GPS antenna
Power Cable
Assembly
PWR-10-
INST-2
454-0010-225
CBL assy, 48V,10m, EXT,
UNTERM, SCRT – 10 meters
Note:Additional power cable lengths are available, please contact your Airspan sales representative.