Aiwa HS-RX693 User manual

SERVICE MANUAL
HS-RX693
HS-RX695
STEREO RADIO CASSETTE PLAYER BASIC TAPE MECHANISM: 6ZM-2 P10NF
S/M Code No. 09-997-413-8R1
REVISION
[YU,YZ]
[YH,YZ]

SPECIFICATIONS
 Design and specifications are subject to change without notice.
Frequncy range: Reception Area EU:
AM 531 kHz - 1602 kHz (9 kHz step)
FM1, FM2 87.5 MHz - 108 MHz (50 kHz step)
Reception Area USA:
AM 530 kHz - 1710 kHz (10 kHz step)
FM1, FM2 87.5 MHz - 108.1 MHz (200 kHz)
Reception Area JPN: <YH, YU>
AM 531 kHz - 1629 kHz (9 kHz steps)
FM1, FM2 76 MHz - 108 MHz
(100 kHz step in 76 MHz - 90 MHz,
50 kHz step in 90 - 108 MHz)
Maximum output: 4 mW + 4 mW (EIAJ/16W) <YZ>
7 mW + 7 mW (EIAJ/32W) <YH, YU>
Power source: Battery DC 3V, size AA(R6) X 2
Domestic AC power (using optional AC adaptor AIWA AC-D302)
Maximum dimensions: 112.9 (W) X 81.2 (H) X 33.8 (D) mm (41/2 x 31/4x 13/8 in.)
Weight: Approx.154.5g (5.4 oz) (excluding batteries)
2

DESCRIPTIONREF.NO. KANRI
NO.
PARTNO. KANRI
NO.
REF.NO. DESCRIPTIONPARTNO.
ELECTRICAL MAIN PARTS LIST
IC
87-002-677-080 IC,TA2002F
87-A21-215-040 C-IC,TA2104AFN
87-A20-904-080 C-IC,TK11823MTL
87-A20-532-040 IC,LB1977M
87-A21-214-010 C-IC,TC9318FB-049
87-A20-638-080 C-IC,PST9120
TRANSISTOR
87-026-604-080 C-TR,IMH9
87-026-352-080 CHIP-TR,DTC144TU
89-113-625-080 TR,2SA1362GR(120MHZ,0.
87-026-585-080 C-TR,IMX1 HQQ
89-327-143-080 TR,2SC2714 (0.1W)
87-026-295-080 C-TR,DTC144TK
89-342-153-080 TR,2SC4215
89-508-804-080 CHIP FET 2SK880Y
89-327-125-080 CHIP TR,2SC2712GR
89-342-132-080 TR,2SC4213
89-341-165-080 CHIP TRANSISTOR 2SC4116GR
87-026-210-080 CHIP-TR,DTC144EK
DIODE
87-A40-462-040 C-VARI-CAP,SVC347(S)
87-A40-655-040 C-VARI-CAP,HVU200A
87-A40-360-080 C-DIODE,MA786
87-A40-630-040 C-DIODE,RB411D
87-017-883-010 LED,SLC22 VR3F
87-017-779-080 C-DIODE,1SS355
MAIN C.B
BPF201 87-A90-601-010 FLTR,BPF GFWB7
C101 87-012-272-080 C-CAP,U 680P-50 B
C102 87-012-272-080 C-CAP,U 680P-50 B
C103 87-012-272-080 C-CAP,U 680P-50 B
C104 87-012-272-080 C-CAP,U 680P-50 B
C105 87-A10-031-080 C-CAP,U 0.01-25 KB
C106 87-A10-031-080 C-CAP,U 0.01-25 KB
C107 87-016-296-080 C-CAP,TN 22-4SV(A)
C108 87-016-296-080 C-CAP,TN 22-4SV(A)
C109 87-010-787-080 CAP, U 0.022-25
C110 87-010-787-080 CAP, U 0.022-25
C113 87-012-278-080 C-CAP,U 2200P-50 B
C114 87-012-278-080 C-CAP,U 2200P-50 B
C115 87-A10-263-080 C-CAP,U 0.1-16ZF
C116 87-A10-263-080 C-CAP,U 0.1-16ZF
C117 87-010-502-010 CAP GAS 100-4
C118 87-010-502-040 CAP ELECT GAS 100/4
C119 87-016-296-080 C-CAP,TN 22-4SV(A)
C120 87-010-424-080 CAPACTOR,TANTAL 4.7-4
C121 87-A10-262-080 C-CAP,U 1-10 ZF
C122 87-016-396-080 C-CAP,U 0.22-16F
C123 87-A10-262-080 C-CAP,U 1-10 ZF
C124 87-010-503-040 CAP,E 220-4 GAS
C151 87-A10-262-080 C-CAP,U 1-10 ZF
C152 87-A10-262-080 C-CAP,U 1-10 ZF
C153 87-A10-706-080 C-CAP,U 0.33U-16 F Z
C154 87-A10-706-080 C-CAP,U 0.33U-16 F Z
C155 87-010-805-080 CAP, S 1-16
C156 87-010-805-080 CAP, S 1-16
C157 87-A10-262-080 C-CAP,U 1-10 ZF
C158 87-A10-262-080 C-CAP,U 1-10 ZF
C159 87-A10-263-080 C-CAP,U 0.1-16ZF
C201 87-012-195-080 C-CAP,U 100P-50CH
C202 87-010-829-080 CAP, U 0.047-16
C203 87-A10-262-080 C-CAP,U 1-10 ZF
C204 87-010-497-040 CAP,E 4.7-35 GAS
C206 87-010-785-080 C-CAP,U0.015-25BK
C207 87-010-785-080 C-CAP,U0.015-25BK
C208 87-A10-263-080 C-CAP,U 0.1-16ZF
C209 87-A10-262-080 C-CAP,U 1-10 ZF
C210 87-A10-263-080 C-CAP,U 0.1-16ZF
C211 87-A10-025-080 C-CAP,U 0.22-16Z F
C212 87-012-278-080 C-CAP,U 2200P-50 B
C213 87-A10-031-080 C-CAP,U 0.01-25 KB
C214 87-012-172-080 CAPACITOR CHIP U 10P CH
C215 87-010-336-080 C-CAP,S 18P-50 UJ
C217 87-A10-031-080 C-CAP,U 0.01-25 KB
C219 87-012-162-080 C-CAP,U 1P-50 CK
C220 87-A10-031-080 C-CAP,U 0.01-25 KB
C221 87-012-170-080 C-CAP,U 8P-50 CH
C222 87-012-270-080 CAP, U 470P-50
C223 87-A10-031-080 C-CAP,U 0.01-25 KB
C224 87-012-172-080 CAPACITOR CHIP U 10P CH
C225 87-012-274-080 CHIP CAP,U 1000P-50B
C226 87-012-140-080 CAP 470P
C227 87-012-191-080 CHIP CAP 68 PF
C228 87-A10-263-080 C-CAP,U 0.1-16ZF
C229 87-A10-262-080 C-CAP,U 1-10 ZF
C230 87-A10-031-080 C-CAP,U 0.01-25 KB
C231 87-010-787-080 CAP, U 0.022-25
C232 87-012-164-080 C-CAP,U 2P-50 CK
C233 87-A10-031-080 C-CAP,U 0.01-25 KB
C234 87-012-182-080 C-CAP,U 27P-50 CH
C401 87-A10-828-080 C-CAP,U 0.33-6.3 K B
C402 87-A10-263-080 C-CAP,U 0.1-16ZF
C403 87-A10-827-080 C-CAP,U 0.47-6.3 K B
C404 87-A10-504-080 C-CAP,U 0.047-16 K B
C405 87-A10-504-080 C-CAP,U 0.047-16 K B
C406 87-A10-504-080 C-CAP,U 0.047-16 K B
C407 87-A10-504-080 C-CAP,U 0.047-16 K B
C408 87-A10-263-080 C-CAP,U 0.1-16ZF
C409 87-A10-263-080 C-CAP,U 0.1-16ZF
C503 87-010-502-040 CAP ELECT GAS 100/4
CF201 87-A90-991-010 FLTR,SFE10.7 MS239-A
CF202 87-A90-991-010 FLTR,SFE10.7 MS239-A
CF203 87-A91-162-010 FLTR,PFS450A7
IFT201 87-A91-366-010 IFT,MW 5PLG
J101 87-A60-438-010 JACK,3.5 BLK<693>
J101 87-A60-437-010 JACK,3.5 BLK 4P<695>
J501 87-A60-849-010 JACK,DC DIA 2.75 BLK
L101 87-A50-322-080 C-COIL,S BK2125 LM252
L102 87-A50-322-080 C-COIL,S BK2125 LM252
L103 87-A50-322-080 C-COIL,S BK2125 LM252
L104 87-A50-322-080 C-COIL,S BK2125 LM252<695>
L201 87-HRA-603-010 BAR-ANT,MW
L202 8Z-HR8-612-010 COIL,FM RF
L203 8Z-HR8-613-010 COIL,FM OSC
L204 87-003-226-080 MICRO INDUCTOR 100UJ
L205 87-005-906-080 C-COIL,S 10.0UHK
PS651 87-A90-440-010 SNSR,PHOTO GP2S24N2-
S101 87-A90-050-010 SW, SL 2-2-2 NS (BLK)
S151 87-A90-050-010 SW, SL 2-2-2 NS (BLK)
S701 87-A91-421-010 SW,LEAF 6ZM-2(H)
S702 87-A90-361-010 SW,PUSH SPPB51-H11.3
SFR401 87-A90-734-080 C-SFR,33K B RH03AXAN4X
TC201 87-011-252-080 TRIMMMER 10P LAR
TH401 87-A90-477-080 C-THMS,157-502-53002-TP
VR101 87-A90-479-010 VR,RTRY 20KAX2
X201 87-A91-094-010 FLTR,CDA10.7 MG80A
CONT C.B
C301 87-012-191-080 CHIP CAP 68 PF
C302 87-012-167-080 C-CAP,U 5P-50 CH
C303 87-012-170-080 C-CAP,U 8P-50 CH
C304 87-A10-263-080 C-CAP,U 0.1-16ZF
3

DESCRIPTIONREF.NO. KANRI
NO.
PARTNO. KANRI
NO.
REF.NO. DESCRIPTIONPARTNO.
4
C305 87-A10-262-080 C-CAP,U 1-10 ZF
C306 87-010-787-080 CAP, U 0.022-25
C307 87-A11-282-080 C-CAP,S 1-16 K B
C308 87-A10-263-080 C-CAP,U 0.1-16ZF
C310 87-012-274-080 CHIP CAP,U 1000P-50B
C601 87-012-274-080 CHIP CAP,U 1000P-50B
C602 87-A10-262-080 C-CAP,U 1-10 ZF
C603 87-A10-262-080 C-CAP,U 1-10 ZF
C604 87-012-174-080 CAP CHIP CERA SS 12P CHJ
C605 87-012-176-080 CAP 15P
C606 87-A10-706-080 C-CAP,U 0.33U-16 F Z
C607 87-A10-263-080 C-CAP,U 0.1-16ZF
C608 87-A10-263-080 C-CAP,U 0.1-16ZF
C609 87-A10-263-080 C-CAP,U 0.1-16ZF
C610 87-A10-263-080 C-CAP,U 0.1-16ZF
C611 87-A10-262-080 C-CAP,U 1-10 ZF
C612 87-A10-262-080 C-CAP,U 1-10 ZF
C613 87-A10-262-080 C-CAP,U 1-10 ZF
C614 87-012-274-080 CHIP CAP,U 1000P-50B
C615 87-012-270-080 CAP, U 470P-50
L301 87-A50-230-080 C-COIL,D-D(CP4LBM)
LCD601 8Z-HR8-606-010 LCD,AIW4184
R606 87-022-245-080 C-RES U 18K-1/16WF
S601 87-A90-665-080 C-SW,TACT LS7A2M
S602 87-A90-665-080 C-SW,TACT LS7A2M
S603 87-A90-665-080 C-SW,TACT LS7A2M
S604 87-A90-665-080 C-SW,TACT LS7A2M
S605 87-A90-665-080 C-SW,TACT LS7A2M
S606 87-A90-665-080 C-SW,TACT LS7A2M
S607 87-A90-665-080 C-SW,TACT LS7A2M
S608 87-A90-665-080 C-SW,TACT LS7A2M
S609 87-A90-665-080 C-SW,TACT LS7A2M
S610 87-A90-330-080 C-SW,SL 1-1-2 SSSS81
X601 87-030-431-010 VIB,XTAL 75K(KF-26)
SW C.B
S611 87-A91-365-080 C-SW,PUSH 1-1-1 SPVG21
FLEX C.B
PH1 8Z-HKE-619-010 HEAD,ASSY 6ZM-2(P10)

BE
C
TRANSISTOR ILLUSTRATION
S
D
G
E1
C1
B1 C2
E2
B2
2SA1362
2SC2712
2SC2714
2SC4116
2SC4213
2SC4215
DTC144EK
DTC144TK
DTC144TU
2SK880Y IMH9
IMX1 HQQ
88
A
Resistor Code
Chip Resistor Part Coding
Figure
Value of resistor
Chip resistor
Wattage Type Tolerance
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
CJ
CJ
CJ
Form LW t
1.6 0.8 0.45
2 1.25 0.45
3.2 1.6
108
118
128
: A
: A
CHIP RESISTOR PART CODE
0.55
Resistor Code
Dimensions (mm)
Symbol
1/16W 1005 5% CJ
1.0 0.5 0.35 104
Lt
W
56
LCD DIAGRAM
LCDAIW 4184

7 8
WIRING-1 (MAIN)

SCHEMATIC DIAGRAM-1 (MAIN)
910

WIRING-2 (CONT 1/2)
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
11 12

WIRING-3 (CONT 2/2)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
1413

IC BLOCK DIAGRAM
1615
IC, TA2104AFN
IC, PST9120
IC, TK11823MTL
IC, LB1977M
IC,TA2002F

SCHEMATIC DIAGRAM-2 (CONT)
17 18

Pin No. Pin Name I/O Description
1 ~ 3 COM1 ~ COM3 O LCDcommon output.
4 ~ 22 SEG1 ~ SEG19 O LCDsegment output.
23 SEG20 (KR3) O LCD segment/ key matrix timing output.
24~26 KR2~KR0 O Key matrix timing output.
27~30 K0~K3 I Key matrix input.
31 MOT ON O Motor drive control terminal. H : ON, L : OFF.
32 MOT HI O Motor speed control terminal. H : HI, L : LO.
33 MOT DIR O Motor rotate direction control terminal. H : Counterclockwise, L : Clockwise.
34 BRAKE O Motor brake control terminal. H : ON, L : OFF.
35 LOAD CTL O Battery remain voltage check signal output terminal. H : ON.
36 AM OUT O FM/ AM control terminal. H : AM, L : FM.
37 F/R CTL O FWD/ REV control terminal.H : FWD, L : REV.
38 MOT CH I Motor rotate detection terminal (Connected to ground).
39 TIMING SW I Mecha status detection switch input terminal.
40 P-SNSR I Photosensor signal input terminal.
41 C-SW I Cassette tape detection switch input terminal. L : Exist cassette tape.
42 L.V. STOP I Reduction voltage detect signal input terminal. L : Reduce.
43 REMOTE I Remotecontrollerkey inputterminal.
44 EJECT SW I Cassette tape eject SW input terminal. L : Eject.
45 HOLD I Key hold switch input terminal (main unit side). H : Hold.
46 BUZR O Buzzeroutputterminal.
47 POWER MUTE O Mute signal output terminal. H : ON, L : OFF.
48 TEST I Test mode control input terminal (Connected to ground).
49 WAKE I Backupdetection signalinputterminal.
50 IF IN I IF counter input terminal.
51 TU OUT O TU operation control terminal. H : TU OFF, L : TU ON.
52 PLL OUT O Phase Comparator output terminal.
53 GND - Connected to ground.
54 FM IN I FM programmable counter input terminal.
55 AM IN I AM programmble counter input terminal.
56 VDD - Voltage supply.
57 RESET I System reset signal input terminal.
58 X OUT I/O Connected tocrystaloscillator.
59 X IN I/O Connectedtocrystal oscillator.
60 VXT - Power supply for crystal oscillator.
61 VLCD - Reference voltage for LCD driver.
62,63 C1,C2 - Double boost up voltage for LCD driver.
64 VEE - Constant 1.5V for LCD driver.
IC, TC9318FB-049
IC DESCRIPTION ADJUSTMENT <TUNER/DECK>
VR101
TC201
TP1 (VT)
L202
SFR 401
IFT201
L201 BAR ANT
J101
6
3
8
5 6
2
2
4
1
7
L203
7
8
MAIN C.B
A
19 20

21
ADJUSTMENT
<TUNER>
1. MW IF Adjustment
IFT 201.............................................................. 450kHz
2. MW Tracking Adjustment
L201................................................................... 630kHz
TC201................................................................ 1440kHz
3. MW VT Check
Settings :  Test point : TP1 (VT)
Method : Set to MW 530kHz and check that the test
point voltage is 1.2V ± 0.2V. Then set to
MW 1602kHz and check that the test point
voltage is less than 8.0V. Next, set to MW
1710kHz and check that the test point voltage
is less than 9.0V.
4. FM Tracking Adjustment <Except YU>
L202................................................................... 87.5MHz
Method : Set to 108.0MHz and make sure to obtain
amplitude of 76.0MHz or more on tracking
scope.
5. FM Tracking Adjustment <YU>
L202................................................................... 87.5MHz
Method : Set to 108.1MHz and make sure to obtain
amplitude of 87.5MHz or more on tracking
scope.
6. FM VT Adjustment <Except YU>
Settings :  Test point : TP1 (VT)
 Adjustment Location : L203
Method : Set to FM 87.5MHz and adjust L203 so that
the test point voltage becomes 2.8V ± 0.1V. Then
set to FM 108.1MHz and check that the test
point voltage is less than 7.0V.
7. FM VT Adjustment <YU>
Settings :  Test point : TP1 (VT)
 Adjustment Location : L203
Method : Set to FM 87.5MHz and adjust L203 so that the
test point voltage becomes 2.8V ± 0.1V. Then
set to FM 108.0MHz and check that the test
point voltage is less than 7.0V.
<DECK>
8. Tape Speed Adjustment
Settings :  Test tape : TTA100(TAPE CENTER)
 Test point : PHONES JACK (J101)
 Adjustment location : SFR401
Method : Play back the test tape and adjust SFR401 so that
the frequency becomes 3015Hz ± 10Hz(FWD)
and 3015 ± 40Hz (REV).
PRACTICAL SERVICE FIGURE
<TUNER SECTION>
Sensitivity :
(S/N 10dB) A M Less than 57dB
[at 630kHz]
Less than 55dB
[at 999/1000kHz
Less than 53dB
[at 1440kHz]
(IHF,THD 3%) F M Less than 17dB
[at 87.5MHz]
Less than 17dB
[at 98.5MHz]
Less than 18dB
[at 108.0/108.1MHz]
Intermediate frequency :
FM 10.7MHz ± 0.1MHz
A M 450kHz ± 3kHz
<TAPE SECTION>
Tape speed : 3015Hz ± 50Hz
Wow : Less than 0.55% (RMS)
Take-up torque : 20 ~ 30g-cm (FWD,REV)
F.F/REW torque : 70 ~ 150g-cm
Back tension : 1.0 ~ 3.0g-cm (FWD,REV)
S/N ratio : More than 43dB (PB, DC)
Distortion : Less than 2.5% (PB, DC)
Noise level : Less than 3.5mV
(Vol MAX, PB, DC)
Less than 0.3mV
(Vol MIN, PB, DC)
Frequency response : 63Hz + 0/  8dB ~ 8kHz ± 4dB
(NORMAL)
63Hz + 0/  8dB ~ 10kHz ± 4dB
(CrO2)
Test tape : TTA  100
TTA  210
TTA  320 (NORMAL)
TTA  310 (CrO2)

MECHANICAL EXPLODED VIEW 1/1
22
14
15
3
17 18
6ZM-2
P10NF
16
10
BAR ANT
19
20
MAIN C.B
21
22
24
23
13 12
CONT C.B
PWB
FLEX 27P
11
LCD 9
5
2
1
8
7
6
4
B
A
E
B
G
F
AD
D
C
G

MECHANICAL PARTS LIST 1/1
1 8Z-HR8-008-010 KNOB,SL HOLD
2 8Z-HR8-009-010 KEY,TUNING
3 8Z-HR8-001-010 LID,CASS<693YU>
3 8Z-HR8-019-010 LID,CASS 693 Z<693YZ>
3 8Z-HR8-015-010 LID,CASS 695<695YH>
3 8Z-HR8-020-010 LID,CASS 695 Z<695YZ>
4 8Z-HR8-207-010 PLATE,STOPPER
5 8Z-HR8-204-010 SPR-T,OPEN
6 8Z-HR8-005-010 WINDOW,LCD
7 8Z-HR8-007-010 KEY,CONT
8 8Z-HR8-006-010 PANEL,BASE
9 8Z-HR8-010-010 KEY,ENTER
10 8Z-HR8-213-010 HLDR,LCD
11 8Z-HR8-214-010 CONN, RUBBER1.3-30.5
12 8Z-HR8-210-010 COVER, PWB
13 8Z-HR8-208-010 SPR-P,POP UP
14 87-HG6-204-010 SPR-P,CASS
15 8Z-HR8-003-010 FRAME,CENTER
16 8Z-HR8-215-010 SPR-E,OPEN
17 8Z-HR8-012-010 KNOB,SL OPEN
18 8Z-HR8-203-010 PLATE,LOCK
19 8Z-HR8-201-010 HLDR,ANTENNA
20 8Z-HR8-206-010 TERMINAL,BAT-
21 8Z-HR8-205-010 TERMINAL,BAT+
22 8Z-HR8-202-010 HLDR,SW
23 8Z-HR8-004-010 LID,BATT
24 8Z-HR8-002-010 CABI,REAR<693YU,695YH>
24 8Z-HR8-021-010 CABI,REAR Z<695YZ,693YZ>
A 8Z-HR8-212-010 S-SCREW,+1.4-4.5 CR HL
B 87-067-430-010 VT1.4-5 BLK
C 87-HK5-235-010 S-SCREW,1.4-0.6-2.5
D 8Z-HR8-211-010 S-SCREW,+1.4-8 BLK HL
E 87-067-384-010 SCREWVT1.4-3.5HL
F 8Z-HR8-209-010 S-SCREW,+1.7-3.5 BLK HL (0.3)
G 88-HJ3-219-010 S-SCREW,+1.4-2.5 B HL(0.3)
DESCRIPTIONREF.NO. KANRI
NO.
PARTNO.
Basic color Color Basic color Color Basic color Color
symbol symbol symbol
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange
COLOR NAME TABLE
23

TAPE MECHANISM EXPLODED VIEW
2
3
4
5
6
6
1
7
8
9
10
11
43
41
42
20
21
22
25
26
22
23
44
18
39
38
a
b
c
d
e
a
b
c
d
e
f
HEAD FLEX C.B
43
32
40
SH,1.2-2.9-0.25SL
SH,1.2-2.9-0.25SL
13
15
24
27
28
30
31
34
35
36
37
17
17
29
16
F
49
49
19
45
46
47
33
12
f
D
A
50
50
C
B
B
20
C
Gg
g
51
14
E
54
54
48
24

DESCRIPTIONREF.NO. KANRI
NO.
PARTNO. KANRI
NO.
REF.NO. DESCRIPTIONPARTNO.
TAPE MECHANISM PARTS LIST 1/1
25
1 86-ZM2-255-010 SPR-T,PIN BACK L
2 86-ZM2-252-610 GUIDE,TAPE
3 86-ZM2-220-210 SPR-T,HEAD
4 86-ZM2-219-510 LEVER,HEAD
5 86-ZM2-347-010 LEVER,MS EJECT
6 86-ZM2-226-110 ROLLER ASSY,PINCH
7 86-ZM2-254-010 SPR-T,PIN BACK
8 86-ZM2-230-110 SPR-T,PINCH L
9 86-ZM2-229-110 SPR-T,PINCH R
10 86-ZM2-240-110 CAP,REEL
11 86-ZM2-234-110 SHAFT,REEL R
12 86-ZM2-251-310 SHAFT,GEAR B
13 86-ZM2-361-110 CHAS ASSY,OUT-SERT P10
14 86-ZM2-349-010 SPR-E,EJECT
15 86-ZM2-232-310 LEVER,REEL R
16 86-ZM2-268-310 SHAFT,PULLEY BELT 2
17 86-ZM2-243-310 SPR-C,BT
18 86-ZM2-329-210 BELT,P5
19 86-ZM2-209-310 GEAR,B
20 86-ZM2-238-710 GEAR,FF
21 86-ZM2-245-410 SPR-C,SLIP L
22 86-ZM2-237-010 GEAR,PLAY
23 86-ZM2-241-310 SPR-C,SLIP R
24 86-ZM2-272-010 LEVER,SW P 8.4
25 86-ZM2-236-510 CAP,SLIP
26 86-ZM2-235-210 SHAFT,REEL L
27 86-ZM2-223-310 LEVER,PIN UP L
28 86-ZM2-233-310 LEVER,REEL L
29 86-ZM2-208-310 GEAR,A
30 86-ZM2-217-210 SPR-E,CAM L
31 86-ZM2-216-510 LEVER,CAM L
32 86-ZM2-276-010 PULLEY,COUPLER
33 86-ZM2-212-310 SHAFT,FR
34 86-ZM2-214-510 LEVER,CAM R
35 86-ZM2-215-210 SPR-E,CAM R
36 86-ZM2-222-410 LEVER,PIN UP R
37 86-ZM2-218-310 LEVER,HEAD UP
38 86-ZM2-205-410 FLY-WHL,L
39 86-ZM2-330-010 FLY-WHL,R2
40 86-ZM2-282-010 SH,AUTO 2
41 86-ZM2-225-310 ARM,PINCH L
42 86-ZM2-224-210 ARM,PINCH R
43 86-ZM2-283-210 CAP,SHAFT
44 86-ZM2-275-310 CAP,SLIP R
45 86-ZM2-210-710 LEVER,FR
46 86-ZM2-211-210 GEAR,FR
47 86-ZM2-213-210 SPR-C,FR
48 M8-6ZS-393-000 ABL-63 D
49 86-ZM2-221-010 CLR,BRG N
50 86-ZM2-239-010 FELT,
51 86-ZM2-342-010 LEVER ASSY,EJECT
A 86-ZM2-278-010 W-P,1.36-4-0.2 SLT
B 86-ZM2-319-010 W-L,0.95-3-0.35
C 87-067-860-010 PW,3-0.95-0.4
D 87-067-516-010 PW,3-1.58-0.25,SLIT
E 88-HK5-228-010 S-SCREW,+1.4-2 CR
F 86-ZM2-348-010 S-SCREW,+1.4-4.6
G 87-261-500-310 SCREW V+1.4-1.4 (BK)

SPRING APPLICATION POSITION
C0.3
86-ZM2-243-310
SPR-C,BT
86-ZM2-243-310
SPR-C,BT
86-ZM2-241-310
SPR-C,SLIP R
86-ZM2-245-410
SPR-C,SLIP L
86-ZM2-220-210
SPR-T,HEAD
86-ZM2-255-010
SPR-T,PIN BACK L
86-ZM2-215-210
SPR-E,CAM R
86-ZM2-229-110
SPR-T,PINCH R
86-ZM2-217-210
SPR-E,CAM L
86-ZM2-230-110
SPR-T,PINCH L
86-ZM2-254-010
SPR-T,PIN BACK
86-ZM2-213-210
SPR-C,FR
26

ACCESSORIES / PACKAGE LIST
DESCRIPTION
REF.NO. KANRI
NO.
PARTNO.
1 8Z-HR8-951-010 RC UNIT,RC695 <695>
2 8Z-HR8-905-010 IB,YH(ECK)S 695<YH(695)>
2 8Z-HR8-903-010 IB,YU(3L)S 693<YU(693)>
2 8Z-HR8-917-010 IB,YZ(EGF)S 693<YZ(693)>
2 8Z-HR8-907-010 IB,YZ(EGF)S 695<YZ(695)>
2 8Z-HR8-919-010 IB,YZ(PHNCZ)S 693<YZ(693)>
2 8Z-HR8-909-010 IB,YZ(PHNCZ)S 695<YZ(695)>
2 8Z-HR8-918-010 IB,YZ(SID)S 693<YZ(693)>
2 8Z-HR8-908-010 IB,YZ(SID)S 695<YZ(695)>
3 84-447-019-310 CLIP,BELT
4 87-B30-123-210 HEADPHONE,M006(T)<YZ(693)>
4 87-B30-080-010 HEADPHONE,M009(F)<YU(693)>
4 87-B30-251-010 HEADPHONE,HP-M042(F)<695>
27

211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:[phone]
L
Printed in Singapore
A4
9920588 931261