AJAX Systems MotionProtect Outdoor User manual
MotionProtect Outdoor User Manual
MotionProtect Outdoor
is a wireless outdoor motion detector for the Ajax security
system. The detector communicates with the hub via protected
radio
protocol at a distance up to 1,700 meters in the line of sight. MotionProtect
Outdoor features protection against blocking the detector view (anti-masking
system) and triggering by pets (pet immunity). The motion detection distance is
adjustable: from 3 up to 15 meters.
MotionProtect Outdoor can operate both on pre-installed batteries or use an
external power supply. Depending on the detector settings, the batteries’ life is up
to 5 years.
Jeweller
ocBridge Plus
uartBridge
Windows. The security system noti�es users of all events through push
noti�cations, SMS, and calls (if activated).
The Ajax security system can be connected to a central monitoring station of a
security company.
Functional Elements
Buy outdoor motion detector MotionProtect Outdoor
1.
Main light indicator
2.
Upper light indicator and masking sensor
3.
Upper motion sensor lens
4.
Masking sensor
5.
Lower light indicator and masking sensor
6.
Lower motion sensor lens
7.
SmartBracket attachment panel (perforated part is required for actuating the
tamper button in case of any attempt to dismantle the detector)
8.
The hole for attaching SmartBracket panel with a screw
Operating Principle
When the system is armed, the detector continuously receives signals from two
PIR sensors. If both sensors detect identical motion, MotionProtect Outdoor
instantly transmits an alarm signal to the hub and blinks with a green LED.
MotionProtect Outdoor ignores animals, birds, insects, as well as swaying plants
and trees.
10.
Tamper button
11.
QR Code
12.
Connector for external power supply cable outlet
13.
Scrollbar for adjusting the motion detection range
If a motion is detected before the system is armed, the detector will be armed not
immediately, but during the next polling by the hub.
Anti-masking system
Masking
is an attempt to block in any way the view of the detector’s lens.
MotionProtect Outdoor detects the following types of masking:
If one or more types of masking are detected, the detector generates a masking
alarm and lights up a green LED for 1 second.
MotionProtect Outdoor detects masking regardless of the security state: armed or
disarmed.
Response time to masking
Learn more about the algorithm of the detector operation
An obstacle in front of both lenses (an object on the height of the detector and
at a distance of up to 20 cm in front of it)
An obstacle in front of any of the lenses (an object at a distance of up to 10 cm
in front of one of the lenses)
Painting or pasting any of the lenses with an opaque substance
Pasting the detector front side with an opaque substance
Applying an aerosol or painting the detector front side with paint
Connecting
Before starting connection:
How to connect the device to the hub:
1.
Following the hub user guide, install the
. Create the account, add the
hub, and create at least one room.
Ajax app
2.
Switch on the hub and check the internet connection (via Ethernet cable and/or
GSM network).
3.
Make sure that the hub is disarmed and does not update by checking its status
in the Ajax app.
1.
Select the
Add Device
option in the Ajax application.
For the detection and interfacing to occur, the detector should be located within the
coverage area of the wireless network of the hub (at a single protected object).
Request for connection to the hub is transmitted for a short time at the time of
switching on the device.
3.
Select
Add
— the countdown will begin.
4.
Switch on the device by pressing the on/off button for 3 seconds.
MotionProtect Outdoor, and then follow the standard addition procedure.
If the connection to the hub failed, repeat the connection attempt after 30 seconds.
The device connected to the hub will appear in the list of devices of the hub in the
app. The update of the detector statuses in the list depends on the device ping
interval set in the hub settings (the default value is 36 seconds).
States
Parameter
Value
1.
2.
How battery charge is displayed in
Ajax apps
Settings
No
Lid only
Entirely
By number of alarms
added to the system
How to �nd the �rmware version or
the ID of the detector or device?
sirens
�rmware
version 3.50 and later
Indication
Deactivate entirely
Deactivate lid noti�cations
Learn more about temporary
deactivation of devices
Learn more about auto deactivation of
devices
Turned-on detector indication
Event
Indication
Note
Functionality Testing
The Ajax security system allows conducting tests for checking the functionality of
connected devices.
The tests do not start immediately but within a period of 36 seconds when using
Support
Service
Battery replacement
According to the requirements of EN50131, the level of the radio signal sent by
wireless devices is reduced during the test mode.
Choosing an installation place
Install MotionProtect Outdoor at the height of 0.8 – 1.3 m, ensuring the upper lens
axis to be parallel to the ground, and the supposed intrusion path is perpendicular
to the lens axis.
When choosing the installation place, consider the maximum device detection
range. It depends on the sensitivity level and the position of the regulator for
adjusting the motion detection range.
Regulator position
Sensitivity level
Motion detection range
The detection range was tested at an ambient temperature of +23°C and clear
seconds.
Check the detector functioning at the alleged installation place. When choosing the
location of MotionProtect Outdoor, take into account the radio signal
communication range.
If the signal level is low (one bar), we cannot guarantee the stable operation of the
detector. Take all possible measures to improve the quality of the signal. At least,
move the detector: even a 20 cm shift can signi�cantly improve the quality of
signal reception.
If the detector has low or unstable signal strength even after moving, use a
.
Do not install the detector:
ReX
radio signal range extender
Without Hood for MotionProtect Outdoor in a place without a covering.
Opposite the trees whose leaves can be in the detection zone of the upper and
lower PIR sensors of the detector.
Opposite the bushes higher than 80 cm.
Install detector at a height 0.8 to 1.3 meters so that its upper lens looks parallel to
the ground. If the site is uneven, the installation height is considered from the
highest point of the territory controlled by the detector.
Detector installation procedure
Why motion detectors react to animals and how to avoid it
1.
Fix the SmartBracket attachment panel on the surface temporarily using
bundled screws or double-sided adhesive tape. Consider the installation height:
0.8 – 1.3 meters.
2.
Select the motion detection distance (3 to 15 m) using the adjustment scroll
bar.
4.
Conduct the Detection Zone Test for upper and lower sensors separately, both
sensors simultaneously, and anti-masking test in the
. If the detector
does not react to motion, select the appropriate sensitivity level, detection
range, and check the detector slope angle.
Ajax app
5.
If all tests have been appropriately passed, �x the SmartBracket to the surface
with screws permanently, put MotionProtect Outdoor on the attachment panel,
and wait until the end of calibration. Fix the detector on the attachment panel
with the bundled screw.
Connecting External Power Supply
MotionProtect Outdoor can use external power supply 5-28 V DC, 200 mA. If the
external power supply is connected, there is no need to remove the pre-installed
batteries. Batteries provide the detector with the backup power source.
To connect the external power supply:
1.
Disassemble the detector body: remove the screws and open the lid.
2.
Break off special caps on the SmartBracket attachment panel:
3. Terminal strips on the detector board
4. The clamp on the back of the detector body
5.
Switch on the power supply. The value of the
External Power Supply
�eld in the
detector settings will change to
Connected
.
6.
Fix the rear of the body with screws, install the detector and wait until the end
break is detected or the tamper is triggered.
Hood Installation
Hood for MotionProtect Outdoor is a cover protecting masking sensors of the
detector from rain and snow. Install it when the detector cannot be placed under
the covering.
To install Hood for MotionProtect Outdoor:
How long Ajax devices operate on batteries, and what affects this
Battery replacement
Buy Hood for MotionProtect Outdoor
1.
Remove the protective �lm from the Dual Lock tape, which is glued to the inner
surface of the hood.
Why motion detectors react to
animals and how to avoid it >
hubs
range
extenders
Table of contents
Other AJAX Systems Security Sensor manuals
AJAX Systems
AJAX Systems DoorProtect Plus User manual
AJAX Systems
AJAX Systems DoorProtect User manual
AJAX Systems
AJAX Systems StreetSiren User manual
AJAX Systems
AJAX Systems Hub Plus User manual
AJAX Systems
AJAX Systems GlassProtect User manual
AJAX Systems
AJAX Systems MotionCam User manual
AJAX Systems
AJAX Systems MotionCam User manual
AJAX Systems
AJAX Systems DoorProtect User manual
