Akerstroms Jupiter Era 4B User manual

954045-000 EN -B0
INSTALLATION MANUAL
REMOTUS JUPITER
Era 4/6/8B, 10BD
RX161, AQ80, TX50
(FSK16)

Revision history
Version Date Reason
A0 2016-12-13 1st released version
A1 2017-01-31 4/6 buttons added, new pictures front page
B0 2017-04-05 TX50 10BD transmitter added
Reference
RX16X conguration tool, manual 952576-000.

3 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
Table of Contents
1 Introduction _____________________________________________________________ 5
2 Scope _________________________________________________________________ 5
3 Use of warnings and notes in this manual ____________________________________ 6
4 Warnings regarding installation and maintenance work_________________________ 6
  ___________________________________________________________ 7
5.1 Design ________________________________________________________________________ 7
5.2 Functional description _____________________________________________________________ 8
6 Installation ______________________________________________________________ 9
6.1 Mechanical installation ____________________________________________________________ 9
6.2 Connections and switches on the MAIN board _________________________________________ 10
6.3 Cable installation________________________________________________________________ 11
6.3.1 Functional diagram ______________________________________________________________________ 12
6.3.2 Principle connection of the Main contactors ___________________________________________________ 12
6.3.3 AC supply______________________________________________________________________________ 13
6.3.4 DC supply _____________________________________________________________________________ 13
6.3.5 Digital inputs ___________________________________________________________________________ 13
6.3.6 Analogue input __________________________________________________________________________ 13
6.3.7 RS422/485 _____________________________________________________________________________ 13
6.3.8 Connection cable ________________________________________________________________________ 13
6.4 Antenna placement ______________________________________________________________ 14
6.4.1 In case of external antenna placement _______________________________________________________ 14
7 Commissioning _________________________________________________________ 15
7.1 Frequency setting _______________________________________________________________ 15
7.1.1 Indication of radio channel quality in Receiver RX161____________________________________________ 15
7.2 Transmittercongurationmode_____________________________________________________ 16
7.2.1 Shutdown Time of the Transmitter ___________________________________________________________ 16
7.2.2 PIN-codeCongurationoftheTransmitter_____________________________________________________ 17
7.2.3 Radio Frequency Setting in the Transmitter____________________________________________________ 18
7.2.4 433 MHz_______________________________________________________________________________ 18
7.2.5 Adjustment of the Push Buttons Remaining and Momentary Functions ______________________________ 20
7.2.6 Radio communication power _______________________________________________________________ 20
7.2.7 Remote type (only Era 8B & 10BD) __________________________________________________________ 21
7.2.8 Heavy weight PIN-code ___________________________________________________________________ 22
7.2.9 System info ____________________________________________________________________________ 22
7.3 Pairing of transmitter and receiver __________________________________________________ 23
7.3.1 Pairing indications _______________________________________________________________________ 23
7.4 Micro (slow speed) Operation ______________________________________________________ 24
7.5 Tandem and Multi-operator Operation _______________________________________________ 24
7.5.1 Multi-operator operation___________________________________________________________________ 25
7.5.2 Tandem operation _______________________________________________________________________ 25
7.5.3 Tandem operator operation & Multi-operator operation __________________________________________ 26
7.5.4 Tandem operator operation & Multi-operator operation (Primary/Secondary) __________________________ 27
7.6 CIM Card______________________________________________________________________ 28
7.6.1 Removing/Mounting CIM Card Era 4/6/8B_____________________________________________________ 28
7.6.2 Removing/Mounting CIM Card 10BD_________________________________________________________ 28
8 Function tests __________________________________________________________ 29
9 Indications _____________________________________________________________ 30
9.1 Receiver indications _____________________________________________________________ 30
9.2 Transmitter indications ___________________________________________________________ 31
9.2.1 Status indicator _________________________________________________________________________ 31
9.2.2 Display indications _______________________________________________________________________ 31

4 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH

Figure 1. Receiver functional safety description _____________________________________________ 8
Figure 2. Mount RX161 ________________________________________________________________ 9
Figure 3. Connections and switches on the MAIN board______________________________________ 10
Figure 4. Installation of cables __________________________________________________________ 11
Figure 5. Relay symbol explanation______________________________________________________ 11
Figure 6. Connection with the two main contactors in parallel, category 3________________________ 12
Figure 7. Connection with the two main contactors in series, category 1_________________________ 12
Figure 8. Internal antenna _____________________________________________________________ 14
Figure 9. Recommended and wrong placement of the antenna ________________________________ 14
Figure 10. Micro operation setting, switch 3 ________________________________________________ 24
Figure 11. Dipswitch SW3, position in the receiver ___________________________________________ 24
Figure 12. Indications on the MAIN board __________________________________________________ 30
Figure 13. LED indicators indicating active outputs___________________________________________ 33
10 Trouble shooting ________________________________________________________ 32
10.1 First check_____________________________________________________________________ 32
10.2 It is impossible to activate the main contactor__________________________________________ 32
10.3 Some output functions do not work__________________________________________________ 33
11 Program Selection ______________________________________________________ 33
11.1 Program Selection list ____________________________________________________________ 33
12 Overview transmitter ____________________________________________________ 42
12.1 Place symbol label ______________________________________________________________ 42
12.2 Symbol explanation______________________________________________________________ 45
List of tables
Table1. Technicalspecications ________________________________________________________ 7
Table 2. Fixed frequency list___________________________________________________________ 19
Table 3. Receiver pairing indication _____________________________________________________ 23
Table 4. Transmitter pairing indication ___________________________________________________ 23
Table 5. Transmitter display pairing indication _____________________________________________ 23
Table 6. Mode, event and indications on the MAIN board ____________________________________ 30
Table 7. Symbol placement for Era 4B and 6B_____________________________________________ 43
Table8. SymbolplacementforthedierenttypesofEra8B __________________________________ 43
Table 9. Symbol placement for 10BD____________________________________________________ 44

Introduction 5 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
1 Introduction
Remotus is Åkerströms product family for radio remote control of safety critical industrial and mobile ap-
plications. Remotus Jupiter is Åkerströms’ standardized industrial remote control product line.
The manual must be used when installing Åkerströms Remotus system to ensure a secure and safe operation.
This manual only covers the installation of the Remotus radio remote control system. Remotus does not
include a complete system for remote control: it has only a set of outputs that is controlled by the operator
with the transmitter switches and joysticks. How the outputs are used to control the object (for example, a
machine’s movements and brakes) depend on the specic installation and is outside the scope of the Re-
motus system.
It is the responsibility of the Systems Integrator or Machine builder to safely incorporate the Remotus radio
remote control into the complete system or machine. The System Integration has to be made by qualied
personnel applying the appropriate standards for the system or machine including making the necessary
safety investigations and risk analysis.
It should be noted that the information obtained from the controlled object is not processed by the Remotus
receiver, but is used for informational purposes.
For the reasons stated above, the safety of Remotus covers mainly the status of the relay outputs, regardless
of the object that is controlled by the relays.
The interface between Remotus and the controlled object should be a special interface that is not included
in Remotus system and therefore is not included in this installation manual.
The approvals for Remotus refer only to the Remotus system not the complete system.
The complete radio control system must be tested and approved in accordance with applicable standards. It
is not part of Åkerströms Björbos responsibility.
2 Scope
The Remotus Jupiter system described in this manual consists of one receiver and one transmitter.
Type Model Symbols
Receiver RX161 J-RX161
Button transmitter AQ80 Jupiter Era 4B
Jupiter Era 6B
Jupiter Era 8B
Nordic, DIN, CS
or numbers
TX50 Jupiter 10BD

Use of warnings and notes in this manual 6 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
3 Use of warnings and notes in this manual
Read all safety instructions throughout this manual and on safety signs attached to this equipment.
Failure to follow all safety instructions could result in death or serious injury.
The safety alert symbol is used to alert about potential personal injury hazards. To avoid hazards, obey all
safety messages that follow this symbol. Inform all personnel that are working with the product.
The following safety alert symbols and signal words are used in this manual to inform the user of hazards.
Indicates a potentially risk of high voltage which, if not avoided,
could result in death or serious injury or property damage.
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury or property damage.
!Indicates a condition which, if not avoided, could result in damage
to or poor functionality of the product.
Electrostatic sensitive devices warning tells you about the risk of
electrostatic discharge which can cause damage to the product.
4 Warnings regarding installation and maintenance work
This manual must be read and understood before installing and starting the radio remote
control system to ensure safe and secure operation.

person in accordance with country installation rules and regulations. Only a correct instal-
lation can ensure the necessary level of safety during use.
󰀨
power supply of the equipment!
Before starting ANY maintenance work ensure by using the external separators / fuses of the
permanent installation, that ALL terminal blocks are free from dangerous voltage!
CAUTION DOUBLE POLE/NEUTRAL FUSING
Risk of high noise level, hearing protection required
If a siren is mounted on the receiver unplug it before any maintenance action.
Put it back when the maintenance is done.

Specications 7 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
5 
General:
Operating frequency: 433-434 MHz
Power output: < 10 mW
Baud rate: 9600 b/s
Transmission principle: GFSK, TDMA
Channel Separation: 25 kHz
Functional sensitivity: ≤-107 dBm BER 10-3
The radio full-lls: R&TTE Directive 99/5EC
Reaction time on STOP function: Maximum 550 ms
Safety category for the Stop function ISO 13849-1 Category 3 PL d
Receiver RX161:
16 Relay outputs:
• 6 safety relays (NO) for movements
• 4 change-over relays (NO/NC)
• 6 normally open relays (NO)
2 Separate main contactor change over safety relays
1 Digital output for horn (siren) 12V
1 Analogue input: 0 (4) -20 mA or 0(2)-10 V
2 Digital inputs: 24/48 V AC/DC (Opto-isolated) or 115/230 V AC (Opto-isolated)
1 Serial port: RS422/RS485
Input voltage: 24/48/115/230 V AC, power consumption less than 14 VA
or 24 V DC 0.5 A. Shall be connected to SELV circuits.
Dimensions: 277x217x115 mm
Weight: Approximately 1.6 kg
Degree of protection (plastic encolsure): IP67
Operating temperature: -25 °C – +55 °C
Storage temperature: -40 °C – +85 °C
Transmitter AQ80: TX50:
Dimensions: 181 x 65 x 43 mm 243x77x41 (49 mm incl. quick stop)
Weight: 265 g 450 g
Degree of protection: IP67 IP65
Display, Graphic LCD: 128x64 pixels 102*64 pixels
Operating Temperature for battery: -20 °C – +55 °C
Storage Temperature for battery: -20 °C – +35 °C
Charging Temperature for battery: +10 °C – +45 °C
NOTE! For charging see charger documentation
Table 1. Technicalspecications
5.1 Design
The RX161 receiver consists of a MAIN board, antenna board (default, otherwise external antenna) and a
radio module. The radio module is located on top of the MAIN board.
The MAIN board holds all logic components, relays, power supply and the connectors.
The enclosure is made of re resistant UL 94-5V plastic.

Specications 8 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
5.2 Functional description
The Remotus RX161 receiver uses a dual channel architecture combined with eight (8) safety re-
lays whereof two safety relays are intended for the safety stop. The other 6 safety relays are used
for crane movement and provides protection against unintended movement due to welded relay
contacts (UMFS Category 3 PL d ISO 13849-1:2006).
The dual channel architecture and extensive use of safety relays in the receiver will signicantly
increase the safety of the crane system providing that the installation is carried out correctly. To
achieve category 3 Pl d for the STOP function according to ISO 13849-1:2006 both safety stop
outputs from the receiver shall be connected to two independent stop inputs on the crane (two
safety stop channels).
signals
+5V
+5V
RADIO Channel A (CPU-A)
Channel B (CPU-B)
Supervising
Power supply and voltage monitoring circuits feeding
power
Main contactor
Safety relays
Figure 1. Receiver functional safety description

Installation 9 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
6 Installation
The permanent installation of the receiver must include fuses to protect the equipment and wiring from over
current and short circuit. In detail the power supply of the receiver and all relay contacts must be fused.
All fuses are used as disconnecting devices. The fuses shall be easily accessible, must submit a contact-gap
of at least 3.0 mm and have to be placed in the line pole (L). NOTE! The neutral line fuse on the PCBA
is NOT sucient as a disconnecting device. After removal of the fuse, parts of the equipment will remain
energized and might represent a hazard during servicing.
6.1 Mechanical installation
Note! Make sure to install any optional accessories inside and/or on the receiver enclosure before mount-
ing the receiver on the crane. Refer to each accessory kit for assembly instructions.
196 mm
229 mm
Ø 6mm
Assembly Instruction - plastic spacer
(optional)
Press the plastic spacers rmly to the bottom
enclosure. Make sure to align the spacers
frame opening with the condensation lter
ventilation on the bottom enclosure lower,
right side.
4 black plastic spacer art. no: 947504-000.
Mount the receiver upright with the cable
glands facing down. The receiver shall be
mounted on a at surface with screws suit-
able for the surrounding environment.
Note! If the plastic spacer is mounted the
screws needs to be 20 mm longer.
Cable diameter
10-16 mm
Cable diameter
3-6.5 mm
Figure 2. Mount RX161
When drilling the hole for the cable gland, make sure
not to damage the printed circuit board or the trans-
former inside. Place some protection inside the enclo-
sure to stop the drill from damaging the interior.

Installation 10 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
6.2 Connections and switches on the MAIN board
MC2
MC1
Pairing
Connection for
radio module
P7
H3
H13
H1 H2
REL9
LED6
YM1
REL6
REL10
P20
REL8
P13
SW2
LED28 LED27
LED25
SW1
ON
1 2 3 4
SW3
LED23
LED19
LED7
LED20 LED22
LED21 LED24
LED17
LED8
B1
YM3
LED2
LED3
LED4
LED1
LED5
P2
48V
55V
230V
24V
0V
115V
TR1
LED26
IC7
REL7
IC9
P5
LED16
P38
YM2
LED18
H5
471-2
PCB1
TP0
P3
P1
P34
REL15REL13
REL12REL11
P33
FUSE1
REL16
REL14
P19
P22
P28
P17
P23
P25
C19
P21
P24
REL18
REL17
P18
P27
P26
H12
H9
H4
H10
H7
YH8
H6
YH9
YH7
YH6
YH5
H11
H8
P30
P38
P31
P29
C66
DIST1
LED12
C65
R298
REL4
LED15
C63
C57
P32
IC17
C64
LED9
950896-000
REL1
P8
R300R264
DIST2
REL3
LED13 LED11
R262
IC16
DIST3
R99
REL5
P12
P16
REL2
SH1
C51
LED10
FUSE1
P15
LED14
P11
YWWPB-Free
Horn (siren)
Analogue in
AC supply
DC supply
24 V DC
Rotary switch
SW1
Rotary switch
SW2
Dipswitch
SW3
Digital input 0 Digital input 1
RS422/485
Support for cabling
Support for cabling
Figure 3. Connections and switches on the MAIN board

Installation 11 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
6.3 Cable installation
If the receiver and/or receiver terminals are connected to more than one line phase the
voltage between any connector must NOT exceed 250 V.
If voltage of one phase is 230 V AC the corresponding three phase voltage is 380 V AC
and thus NOT allowed.
Max loading by relay may not be over 2 A.
Current loops containing relay contacts SHALL therefore have a protection fuse not
higher rated than 6 A.
A protection fuse for the receiver main supply shall be rated 6 A.
Do not mix SELV and NON SELV signals in the same cable.
After the installation of the equipment, the installed cables
must be bound together in pairs (e.g. by using a cable tie)
very close to the terminal blocks (see Figure 4). This is im-
portant if a cable become loose. The cable should not be
able to end up in an unsuitable location of the receiver.
Fasten with a torque of 0.4-0.5 Nm. Figure 4. Installation of cables
Cabling
1
Cable ties
23
Note! The position of di󰀨erent cable glands can vary depending on combination of accessories.
1Relay/digital in and hole mounted siren cabling. Note! Relay cabling, use cable ties not only as in Figure 4 but also to hold
them together in the middle. Hole mounted siren cabling to the left.
2DC supply cabling. Note! The connection from this supply shall be routed through its own cable gland.
3External siren
RS 422/485 and Analogue in. M12 cable gland at suitable placement. Note! Cabling shall be routed to the left or right.
Pigtail for external antenna. BNC chassis connector in the rightmost hole. Note! Cabling shall be routed as shown in 2/ 3
For relay terminal and connector number see Figure 3 on page 10.
NO
NC
Common
NO
Common
Figure 5. Relay symbol explanation

Installation 12 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
6.3.1 Functional diagram
The receiver functional diagram shows how to connect the equipment, in this manual the functional dia-
gram is written as dierent program options, see chapter 11.
6.3.2 Principle connection of the Main contactors
The radio remote control system is, for the safety stop function, designed for category 3 Pl d according to
ISO 13849-1:2006. To achieve this safety level for the object (crane) both safety stop outputs MC1 and
MC2 shall be used as two separate independent outputs (two safety channels). This means that there must
be two main contactors on the machine. See the connection example below.
MC1
MC2
Line
Main contactors
Neutral
Main contactor control
from receiver
fuse 6A
External
Figure 6. Connection with the two main contactors in parallel, category 3
If category 3 is not desired, the two safety stop outputs MC1 and MC2 shall be used connected in series.
See the connection example below. The maximum level of safety for the safety stop function in this case
will be category 1.
MC1 MC2
Line
Main contactor
Neutral
Main contactor control
from receiver
fuse 6A
External
Figure 7. Connection with the two main contactors in series, category 1

Installation 13 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
6.3.3 AC supply
Carefully check the power supply voltage level. 230
115
48
24
N
6.3.4 DC supply
The connection cable for the DC supply shall be routed through
its own cable gland.
Do not mix with NON SELV signals.
24VDC
0
6.3.5 Digital inputs
Carefully check the signal voltage level.
These two signals appear as symbols on the transmitter display.
Dig in 1
24/48V Common
Dig in 0
24/48V Common 115/230V 115/230V
6.3.6 Analogue input
This signal may be used for weight information from a scale,
shown on the transmitter’s display. See section 9.2.2.
Do not mix with NON SELV signals.
6.3.7 RS422/485
This signal may be used for weight information from a scale,
shown on the transmitter’s display. See section 9.2.2.
Do not mix with NON SELV signals.
6.3.8 Connection cable
The cable cross-sectional area shall be at least 0.75 mm²
and with an outer insulation diameter of 10-16 mm.

Installation 14 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
6.4 Antenna placement
The antenna is by default placed internally in Jupiter RX161, see gure below.
Antenna board
Antenna connector
Figure 8. Internal antenna
6.4.1 In case of external antenna placement
When mounting the antenna separately it must be placed as open (in free air) as possible preferably below
the crane beam.
A covered antenna contributes to a considerably less eective radio reception. An antenna can not be
mounted in a cabinet.
Recommended placement
Crane/Hoist
Antenna cable
50 ohm
Wrong placement
Antenna
45˚45˚
Crane
beam
Figure 9. Recommended and wrong placement of the antenna
!The antenna must never come into contact with metal parts.
If the antenna is installed outdoors, there is a risk of dangerous voltages entering the antenna cable.
To minimize this risk a DC block shall be used. DC blocks are coaxial components that prevent the
󰀨
Suitable models have capacitors in series with both the inner and outer conductors.
Åkerströms can provide one suitable DC block 944498-000.

Commissioning 15 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
7 Commissioning
7.1 Frequency setting
Fixed frequency channel set by the user. It´s only in the transmitter the frequency need to be set, see sec-
tion 7.2.3 on page 18.
Note that for 433MHz region “EU” or “Other” is set in both the transmitter and the receiver. For the
receiver refer to Conguration Tool (manual 952576-000) and for the transmitter see 7.2.4 on page 18.
Default setting is “EU”.
7.1.1 Indication of radio channel quality in Receiver RX161
By watching the indications “Squelch” (LED 4) and “Message received” (LED 3) it is possible to diag-
nose the quality of the radio channel (see section 9.1 on page 30).
• Every time a message is received the indication “Squelch” lit. The messages are sent at a constant
rate. The indication “Squelch” shall lit at this rate. If this isn’t the case some of the channels can be
occupied or some of the used frequencies (1 of 15) are not working.
• If the message is accepted by the receiver, indication “Message received” will lit.
If the indication “Message received” does not lit at the same rate as the indication “Squelch” the messages
on one or more frequencies are disturbed or distorted.

Commissioning 16 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
7.2 Transmitter conguration mode

Press the button on the bottom right (2nd step) while
pulling up the safety stop button. Hold down the
button 3 seconds until the status indicator glows yel-
low showing that the transmitter is in conguration
mode.
Submenu
Browse submenu with the top buttons. Choose sub-
menu with the button on the bottom right. To return
to the main menu while you are in a submenu, press
the button on the bottom left.
Submenus:
• “Shutdown”
• “PIN-code”
• “Frequency”
• “433 MHz”
• “Button function”
• “Radio comm power”
• “Remote type”
• “Heavy weight PIN-code”
• “System info”
Exit/Save
Finish by turning the transmitter o by pushing the
safety stop button down. This also saves the changes
that have been made.
Enter cong menu
Browse
Choose
/OK
Browse
Conguration menu
Choose
/OK
BrowseBrowse
7.2.1 Shutdown Time of the Transmitter
The transmitter shuts down automatically if not used for a certain amount
of time. This time can be adjusted in the transmitter conguration menu.
1. Enter the conguration menu.
2. Then select “Shutdown”; with bottom right button (browse with top buttons).
3. Then browse the desired shutdown time with top buttons:
• “2 minutes”
• “5 minutes”
• “15 minutes”
• “no shutdown”
Already selected shutdown time is indicated by top left button LED.
4. Select shutdown time by press down bottom right button.
5. Automatic return to the main menu or restart the transmitter.
Browse
Choose
/OK
Browse
Back
Shutdown time
Choose
/OK
BrowseBrowse
Back

Commissioning 17 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
7.2.2 PIN-code Conguration of the Transmitter
The transmitter is equipped with a user congurable PIN-lock to prevent unauthorized access to the system.
The PIN-lock is disabled by default.
1. Enter the conguration menu.
2. Then select “PIN-code”; with bottom right button (browse with top buttons).
3. Enter PIN:
For enable enter the factory setting 3333 and
for disable enter the old PIN-code.
Press top left button repeatedly to select number and bottom right
button to choose the number. Delete a number with top right.
4. Enter new PIN:
Enter the new 4-digit PIN.
For enable enter the new PIN (not 3333) and
for disable enter the factory setting 3333.
5. Repeat PIN:
Repeat the PIN code.
6. Automatic return to the main menu or restart the transmitter.
Delete
number
Select number
(Press B1
repeatedly)
Choose
number
PIN code Enable/Disable
Choose
number
Select number
(Press B1
repeatedly)
Delete
number
7.2.2.1 Entering PIN-code at start-up
When PIN is enabled the transmitter will not start to transmit before the correct PIN-code is entered. If
the transmitter is PIN locked at startup status indicator shows red continuous light. Display will show
“Enter PIN”.
Enter the 4-digit PIN-code by pressing top left button repeatedly to select number and bottom right
button to choose the number. Delete a number with top right button. When all 4-digit are selected, press
bottom right button once again to select the PIN code.
At successful login the status indicator shows green ashing. Display shows “PIN OK!”. The unit is now in
operating mode.

Commissioning 18 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
7.2.3 Radio Frequency Setting in the Transmitter
!If there is a change be-
tween “EU” or “Other” in the settings, the frequency channel has to be set again!
To change the settings do the following:
1. Enter the conguration menu.
2. Then select “Frequency”; with bottom right button (browse with top buttons).
3. Then browse to the desired setting with top buttons:
• “Channel 0-XX”
Already selected setting is shown when entering the frequency
setting menu.
4. Select setting by press down bottom right button.
5. Automatic return to the main menu or restart the transmitter.
Browse
Choose
/OK
Browse
Back
Choose
/OK
BrowseBrowse
Back
Channel: Sets a specic channel. See “7.2.4.1 Fixed frequency” on page 19.
7.2.4 433 MHz
In frequency band 400 there is an opportunity to select region.
1. Enter the conguration menu.
2. Then select “433 MHz”; with bottom right button (browse with top buttons).
3. Then browse to the desired setting with top buttons:
• “EU” - 30 channel
• “Other” - 60 channel
Already selected setting is indicated by top left button LED.
4. Select setting by press down bottom right button.
5. Automatic return to the main menu or restart the transmitter.
!Note. If the equipment is being operated in EU-region the 433MHz setting

See “Appendix 1 - European Radio Regulation” on page 46.
!
any applicable local, state, or federal governing laws.
!Make sure that correct choice of “EU” or “Other” is set in both the transmit-

952576-000). Default setting is “EU”.
Browse
Choose
/OK
Browse
Back
Choose
/OK
BrowseBrowse
Back

Commissioning 19 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
7.2.4.1 Fixed frequency
Channel no 434MHz EU 433-434MHz Other
0 434,05 433,3
1 434,075 433,325
2 434,1 433,35
3 434,125 433,375
4 434,15 433,4
5 434,175 433,425
6 434,2 433,45
7 434,225 433,475
8 434,25 433,5
9 434,275 433,525
10 434,3 433,55
11 434,325 433,575
12 434,35 433,6
13 434,375 433,625
14 434,4 433,65
15 434,425 433,675
16 434,45 433,7
17 434,475 433,725
18 434,5 433,75
19 434,525 433,775
20 434,55 433,8
21 434,575 433,825
22 434,6 433,85
23 434,625 433,875
24 434,65 433,9
25 434,675 433,925
26 434,7 433,95
27 434,725 433,975
28 434,75 434
29 434,775 434,025
30 434,05
31 434,075
32 434,1
33 434,125
34 434,15
35 434,175
36 434,2
37 434,225
38 434,25
39 434,275
40 434,3
41 434,325
42 434,35
43 434,375
44 434,4
45 434,425
46 434,45
47 434,475
48 434,5
49 434,525
50 434,55
51 434,575
52 434,6
53 434,625
54 434,65
55 434,675
56 434,7
57 434,725
58 434,75
59 434,775 Table 2. Fixed frequency list

Commissioning 20 (48)
Installation manual Remotus Jupiter 10BD, Era 4/6/8B FSK16 Version: B0 Document-ID: 954045-000 EN Author: SH
7.2.5 Adjustment of the Push Buttons Remaining and Momentary Functions
The buttons either have momentary functions, which give a signal for only as long as you keep pressing,
or remaining functions.
Note that this function needs support from the receiver PLC. Before changing these parameters,

1. Enter the conguration menu.
2. Then select “Button function” with bottom right button (browse with top buttons).
3. Press down the buttons for which you want to have a remaining/momentary function. Lighted but-
ton LED indicates remaining function. Note: The three pair of buttons 1-2, 3-4 and 5-6 must have
the same settings within the pair. For 10BD must also buttons 7-8 have the same settings within
the pair. Otherwise the momentary function is disabled on the button that is not remaining.
4. Restart the transmitter.
7.2.6 Radio communication power
To change the settings do the following:
1. Enter the conguration menu.
2. Then select “Radio comm power”; with bottom right button (browse with top buttons).
3. Then browse to the desired setting with top buttons:
• “100 % power”
• “25 % power”
Already selected setting is indicated by top left button LED.
4. Select setting by press down bottom right button.
5. Automatic return to the main menu or restart the transmitter.
Browse
Choose
/OK
Browse
Back
Choose
/OK
BrowseBrowse
Back