Akerstroms SESAM 800 CONFIGURABLE User manual

954446-000 EN -A1
OPERATING MANUAL
SESAM 800
L15, M6, S6, S3, K3,
RX DIN1

2 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
Revision history
Version Date Reason
A0 2017-05-03 1st released manual
A1 2019-08-21 Type label position added, replacing battery
claried

3 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
Table of Contents
1 Introduction _________________________________________ 4
2 Scope _____________________________________________ 4
3 Service _____________________________________________ 4
4 Maintenance_________________________________________ 4
5 TechnicalSpecications_______________________________ 5
6 Description of the System _____________________________ 6
6.1 Receiver _________________________________________________6
6.2 Transmitters ______________________________________________6
7 Description of the Receiver ____________________________ 7
8 Installation of the Receiver_____________________________ 7
8.1 Placement of the Receiver ___________________________________8
8.2 Connections on the Receiver _________________________________8
9 Indicators on the Receiver _____________________________ 9
10 CongurationoftheReceiver __________________________ 9
10.1 BasicConguration _________________________________________9
10.2 AdvancedConguration ____________________________________10
10.3 ErasingAllTransmittersintheReceiver ________________________10
11 Description of the Transmitters ________________________ 11
11.1 Indicators on the Transmitter_________________________________ 11
12 ReplacingBatteriesintheTransmitters _________________ 13
12.1 ReplacingBatteriesinSesamK3 _____________________________13
12.2 ReplacingBatteriesintheSesam800S3/S6 ____________________14
12.3 ReplacingBatteriesinSesam800M6 _________________________15
12.4 ReplacingBatteriesintheSesam800L15 ______________________16
13 Error Codes for Receiver _____________________________ 17
14 Measure for the Receiver _____________________________ 17

Introduction 4 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
1 Introduction
This manual only covers the installation of the Sesam radio remote door opening
system. The Sesam System is not a complete door opening system: it provides
only the set of outputs that are driven according to the actions performed by the
operator of the transmitter. The way the set of outputs is used for controlling the
doors depends on the specic installation and is outside the scope of the Sesam.
The complete remote control system, where the controlled object is one part, has
to be tested and approved according to the standards/norms that are applicable
and specic to the controlled object. This is not the responsibility of Åkerströms
Björbo.
2 Scope
The following guide must be used when installing Åkerströms Sesam door opening
system to ensure secure, safe operation. The installation must be carried out by
a certied electrician.
3 Service
Contact your Åkerströms Björbo AB dealer for service or support. Warranty
work must be performed by Åkerströms or authorized service center.
4 Maintenance
For cleaning use a dry cleaning cloth, if necessary use a wet cleaning cloth and a
soap solution. Never use an alcohol-based product for cleaning; it can seriously
damage the plastic.

Technical Specications 5 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
5 TechnicalSpecications
SystemSpecications
Operating frequency: 869,8 MHz
Channel separation: 25 kHz
Power output: < 5 mW
Functional sensitivity: <= -107 dBm BER 10-4
Transmission principle: GMSK, TDMA
Operating Temperature: -25°C - +55°C
Storage Temperature: -40°C - +85°C
SpecicationsDIN1
Power Supply 12-24 V AC/DC
Max switching capacity of relays: 2A/250VACwithcosφ=1
Fuse on current loop: 2,5AT/250 V AC (IEC 60127-2/V)
Dimensions: 92 x72,5 x 30 mm
Weight: 84g
SpecicationsK3
IP- class: IP65
Dimensions: 67x44x13 mm
Weight: 30g
Battery type: 2*CR 2025 Lithium cells
Screw Size PH00
SpecicationsS3/S6
IP- class: IP67
Dimensions: 75 x 46 x 22 mm
Weight: 80g
Battery type: 2*AAA/LR03 Alkaline
Screw Size PH00
SpecicationsM6
IP- class: IP67
Dimensions: 100 x 60 x 25 mm
Weight: 130g
Battery type: 2*AA/LR06 Alkaline
Screw Size PH2
SpecicationsL15
IP- class: IP67
Dimensions: 120x75x30
Weight: 200g
Battery type: 2*AA/LR06 Alkaline
Screw Size PH2
Table 1. TechnicalSpecications,Sesam800

Description of the System 6 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
6 Description of the System
6.1 Receiver
Sesam 800 RX DIN1:
1
• 1 Single Pole Double Throw relay.
• Memory capacity: up to 100 transmitters.
• Designed for DIN rail.
6.2 Transmitters
This document covers ve transmitter models:
Keyring K3:
1
• Miniature size 3 button transmitter.
• Controls up to 3 functions on 1-3 receivers.
• Suitable for short transmissions.
Small S3:
• Small size 3 button transmitter.
• Controls up to 3 functions on 1-3 receivers.
Small S6:
1
• Small size 6 button transmitter.
• Controls up to 6 functions on 1-6 receivers.
Medium M6: 1
• Medium size 6 button transmitter.
• Controls up to 6 functions on 1-6 receivers.
Large L15:
• Large 15 button transmitter.
1
• Controls up to 15 functions on 1-15 receivers.
1Type label position

Description of the Receiver 7 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
7 Description of the Receiver
+
-
D4
REL1
B1
TP0
IC3
LED6
LED7
LED5
P2 P3P1 P4 P5
ANT1
P12
12 3 4 5
1. LED indications
LED 7 Learn
LED 6 Status
LED 5 Squelch
2. External antenna
3. Learn/Erase button
4. Power connection
P1, P2
5. Connection to relay 1,
P3, P4, P5
Figure1. Sesam800RXDIN1modelconnectionsandbutton
8 Installation of the Receiver
The permanent installation of the receiver must include fuses that protect the
equipment and wiring from over current and short-circuit. In detail the power
supply of the receiver and all relay contacts must be fused.
All fuses are used as disconnecting devices. The fuses shall be easily accessible,
must submit a contact gap of at least 3.0 mm and have to be placed in the line
pole. Note that the fuse must be compatible with IEC 60127-2/V.
After the installation of the equipment, the installed cables must be bound
together in pairs (i.e. by using a cable binder) very close to the terminal blocks.
Note that there might be hazardous voltage in the receiver; therefore only certi-
ed electricians are allowed to open the lid.

Installation of the Receiver 8 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
8.1 Placement of the Receiver
Select a location that is within the environmental limitations of the receiver and
where it is dicult for unauthorized persons to obtain access to the receiver. If
possible, mount the receiver with the cable glands facing downwards.
SESAM RX DIN is to be mounted on a DIN rail. On
the back there is a recess that the rail ts in (see 1 in
Figure 2). When the recess is pressed against the rail the
snap t (see 2 in Figure 2) will lock the receiver to the
rail automatically. Make sure that the snap. To remove,
withdraw the snap t and lift the receiver o the rail.
Figure2. DINreceiver,thelockfortherail.
8.2 Connections on the Receiver
Power Connection Relay Connection
P1 P2 P3 P4 P5
Line (L) Neutral (N) Common terminal (C) Normally opened (NO) Normally closed (NC)
L N
(C) (NO) (NC)
R1
P1 P2 P3 P4 P5
Figure4. Power connection and Relay connection

Indicators on the Receiver 9 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
9 Indicators on the Receiver
The Sesam 800 RX DIN1 model has three LED indicators that are displaying
system information.
The indications on the LEDs are as follows:
LED6
LED7
LED5
LED7 - Learn Indicates if the transmitter is in Learn Mode.
LED6 - Status Indicates that information from a transmitter
associated with the receiver has been received.
LED5 - Squelch Indicates a detected signal on the operating
frequency band.
10 CongurationoftheReceiver
10.1 BasicConguration
Note! If the receiver relay function shall be altered this has to be done before
pairing the rst transmitter, see section 10.2. By default the relay function is set
to momentary.
+
-
D4
REL1
B1
TP0
IC3
LED6
LED7
LED5
P2 P3P1 P4 P5
ANT1
P12
Learn/Erase button
LED7
1. Press and hold down the Learn/Erase button (≈ 1 s) on the receiver until
LED7 is ON. The Learn Mode will be active for 10 seconds (as long as
LED7 is ON).
Press the button on the transmitter that shall activate the relay, in this
receiver.
2. LED7 on the receiver ashes 3 times if the Learn procedure is successful.

Conguration of the Receiver 10 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
10.2 AdvancedConguration
This conguration allows the user to determine the function of the relay; mo-
mentary or remaining function. Note that this setting is possible only with the
rst transmitter, the transmitter will be learned to the receiver at the same time.
Alternative after all transmitters has been erased, see section 10.3.
Momentary function: Hold in the transmitter button in order to activate the relay.
Remainingfunction: One press on the transmitter button to activate the relay,
nextpressonthebuttonwillde-activatetherelay(on/o󰀨).
+
-
D4
REL1
B1
TP0
IC3
LED6
LED7
LED5
P2 P3P1 P4 P5
ANT1
P12
Learn/Erase button
LED7
LED6
1. Press and hold down the Learn/Erase button (≈ 1 s) until LED7 is ON. The
Learn Mode will be active for 10 seconds. Press the Learn/Erase button
repeatedly until LED6 is indicating the desired function.
Momentary function: LED6 (status) is OFF.
Remaining function: LED6 (status) is ON.
2. Press the button on the transmitter that shall activate the relay in this
receiver. If the conguration is accepted by the receiver, LED7 ashes 3
times. Learn procedure is successful.
10.3 ErasingAllTransmittersintheReceiver
1. Press and hold down the Learn/Erase button until LED7 is ON. The Learn
Mode will be active for 10 seconds.
2. Press and hold down the Learn/Erase button for about 5 seconds (until
LED7 is OFF). All transmitters are now erased from the receiver memory.

Description of the Transmitters 11 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
11 Description of the Transmitters
11.1 Indicators on the Transmitter
Normal operation
Quick ashing RED = sending message.
Continuous GREEN = Relay activated in the receiver (Feedback information from receiver).
Fault indications
3 long RED ashes = Battery depleted, transmitter can not send commands.
Continuous RED after activating command = Low battery.
Very quick ashing RED = Hardware error.
After battery insertion:
Yellow LED ON for 1 second followed by one GREEN ash.
TheSesam800K33buttonkeyringtransmitter
1
21. Status LED
2. Buttons 1-3
Figure5. TheSesam800K3transmitterindicatorandbuttons
The Sesam 800 S6 6 button transmitter
1
2
1. Status LED
2. Buttons 1-6
Figure6. TheSesam800S6transmitterindicatorsandbuttons

Description of the Transmitters 12 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
The Sesam 800 M6 6 button transmitter
1
2
1. Status LED
2. Buttons 1-6
Figure8. TheSesam800M6transmitterindicatorsandbuttons
The Sesam 800 L15 15 button transmitter
1
2
1. Status LED
2. Buttons 1-15
Figure10. TheSesam800L15transmitterindicatorsandbuttons

Replacing Batteries in the Transmitters 13 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
12 ReplacingBatteriesintheTransmitters
12.1 ReplacingBatteriesinSesamK3
If the Status LED on the transmitter indicates low battery, replace the batteries
promptly. Before changing the batteries note that changing of batteries must
take place in a clean environment free from static electricity.
The batteries are changed as follows:
1. Unscrew the 3 screws holding the enclosure together ( 1) with screwdriver
PH00.
2. Carefully remove the back enclosure.
3. Remove the plastic holder and the batteries ( 2).
4. Insert the new batteries ( 3and 2). Make sure the batteries are
inserted in the correct polarity.
5. Close the enclosure
6. Tighten the 3 screws with torque 0.14 Nm.
1 2 32xCR2025
Figure11. BatterylocationinSESAM800K3

Replacing Batteries in the Transmitters 14 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
12.2 ReplacingBatteriesintheSesam800S3/S6
If the Status LED on the transmitter indicates low battery, replace the batteries
promptly. Before changing the batteries note that changing of batteries must
take place in a clean environment free from static electricity.
The batteries are changed as follows:
1. Open the battery cover by unscrewing the six screws on the backside of the
transmitter enclosure with screwdriver PH00.
2. Carefully remove the cover by lifting up the front of the cover.
3. Remove the used batteries.
4. Insert the new batteries. Make sure the batteries are inserted in the correct
polarity.
5. Close the cover by rst inserting the backside of the cover in the transmit-
ter, and then press the front down.
6. Tighten the six screws with torque 0.14 Nm.
+
+-
-
2xAAA
Figure12.
Battery cover and
thescrewsholding
the cover
Figure13. Batteries in the
transmitter
Figure14. Backsideofthe
cover inserted in its
position

Replacing Batteries in the Transmitters 15 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
12.3 ReplacingBatteriesinSesam800M6
If the status indicator on the transmitter indicates low battery, replace the batter-
ies promptly. Before changing the batteries note that changing of batteries must
take place in a clean environment free from static electricity.
The batteries are changed as follows:
1. Open the battery cover by unscrewing the 6 screws on the backside of the
transmitter cover with screwdriver PH2.
2. Carefully remove the cover by lifting up the front of the cover.
3. Remove the used batteries
4. Insert new batteries. Make sure the batteries are inserted in the correct
polarity.
5. Close the cover by rst inserting the backside of the cover in the transmit-
ter, and then pushing the front down.
6. Tighten the 6 screws with torque 1.0 Nm.
2xAA
+
+-
-
Figure15.
Battery cover and
thescrewsholding
the cover
Figure16. Batteries
inserted in the
transmitter.
Figure17. Backsideofthe
cover inserted in its
position

Replacing Batteries in the Transmitters 16 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
12.4 ReplacingBatteriesintheSesam800L15
If the Status LED on the transmitter indicates low battery, replace the batteries
promptly. Before changing the batteries note that changing of batteries must
take place in a clean environment free from static electricity.
The batteries are changed as follows:
1. Open the battery cover by unscrewing the 6 screws on the backside of the
transmitter housing with screwdriver PH2.
2. Carefully remove the cover by lifting up the front of the cover.
3. Remove the batteries.
4. Insert the new batteries. Make sure the batteries are inserted in the correct
polarity.
5. Close the cover by rst inserting the backside of the cover in the transmit-
ter, and then press the front down.
6. Tighten the 6 screws with torque 1 Nm.
2xAA
+
+-
-
Figure18.
Battery cover
and the screws
holdingthe
cover
Figure19.
Batteries in the transmitter
Figure20.
Backsideofthecoverinsertedinits
position

Error Codes for Receiver 17 (20)
S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
13 Error Codes for Receiver
Any of the error states below is displayed with ten quick ashes on the Status
LED (LED6) regardless of fault.
• Id already programmed
• Memory full
• Memory card mismatch during power- up
• Memory card write error. Possible memory card removal during operation
• Memory card copy to verify error
• Internal errors, the unit needs service
• Line power unstable
14 Measure for the Receiver
92
63
Figure21. TheSesam800RXDIN1receivermeasure

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
18 (20)

S800 DIN1 Operating Manual (original instructions) Document-ID: 954446-000 EN
Version: A1 Author: SH
19 (20)

ÅkerströmsBjörboAB
Box 7, SE-785 21 Gagnef, Sweden
street Björbovägen 143
SE-786 97 Björbo, Sweden
Phone [phone]
Fax [phone]
E-mail [email protected]
www.akerstroms.com
©ÅkerströmsBjörboAB,2013